Historically there have been various boot options, SPI flash,
NAND or NOR. The NOR flash is mutually exclusive with MMC, but
it isn't mutually exclusive with NAND or SPI Flash, so this patch
enables both NAND flash and SPI Flash when booting from NOR.
Signed-off-by: Adam Ford <aford173@gmail.com>
The configuration with NOR is mutually exclusive with MMC, and as
such, the filesystem commands were disabled. With the USB host
enabled, this patch enables the file system command which can
be executed on storage devices attached to the USB.
Signed-off-by: Adam Ford <aford173@gmail.com>
The current size allocated to U-Boot is 384k, but U-Boot has grown
to 436K which means that saving the environmental variables wipes
out part of the U-Boot source and the board ceases to function.
Due to the sector and erase size for the NOR part and a desire to
not have to change partition sizes often, this patch moves the
U-Boot environmental variables to an offset of 1M so saveenv
does not brick the board. This patch also sets up MTDIDS and
MTDPARTS to clearly show where U-Boot and U-Boot's environmental
variables are located.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable support for Intel E1000 based PCIe ethernet cards that
can be used to test PCIe RC functionality on AM65x EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.
The following build error is reported if DM watchdog support was
enabled in SPL:
CC spl/drivers/usb/gadget/rndis.o
LD spl/drivers/usb/gadget/built-in.o
LD spl/drivers/usb/musb-new/built-in.o
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.
Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds device tree and driver model watchdog support,
converts the legacy omap watchdog driver to driver model for
TI AM335x chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_HW_WATCHDOG is no more a default option for AM33XX devices
after DT/DM conversion, adjusted kconfig accordingly.
DM watchdog support is enabled by default in SPL. The SPL image
doesn't fit into SRAM because of size constraints and build breaks
with an overflow. For this reason DM watchdog support should be
disabled in SPL, driver code should be adjusted accordingly to serve
this purpose.
Built and tested on AM335x device (BeagleboneBlack), compile tested
for all other AM33xx based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Disable the PSCI_RESET reboot handler to permit handling the reboot
flag and calling the PSCI handler with the flag in parameter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SEI510 board is based on the Amlogic S905X2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905X2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
The board default behaviour is for booting Android and triggers
fastboot on recovery or reboot mode.
USB vendor ID (used by fastboot) is 0x18d1 (Google) for
default udev rules for existing android users work out of the box.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add Macronis SPI flash support - some Omnia routers are shipped with
this SPI flash chip.
Also add the memtest command to defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The mvgbe driver supports DM_ETH so switch these boards to using it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This board is unmaintained and can be removed. This also allows us to
remove kmp204x-common.h and integrate it in kmp204x.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove the PORTL2 board and all its dependencies as it is no longer
supported by the company.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To execute the conversion away from board specific header files, Kconfig
menus have been implemented for all KM boards and additionally for those
having an ARM architecture.
For the moment, the preprocessor definitions stay in the headers. The
boolean types, however, needed a modification (#define CONFIG_* 1).
The default configuration files of some boards required an update in order
to not change the currently defined values of the configurations.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use unified values for USB Product/Vendor numbers
when the config block is missing
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We never really added a sensible DFU configuration for platforms
based on eMMC. Most of the things one might want to do can also be done
with UMS or fastboot, so drop the DFU configuration.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add slimbootloader board to run U-boot as a Slim Bootloader payload
- Add new board/intel/slimbootloader directory with minimum codes
- Add slimbootloader configuration files
- Add doc/board/intel/slimbootloader.rst
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add slimbootloader board MAINTAINERS file]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Converts qemu x86 machines to boot using distro_config. The intent is to
allow u-boot in qemu to be maximally compatible with many boot methods
without having to change the config. Previously, u-boot would only boot
in a very limited set of circumstances where there was a /boot/vmlinuz
on scsi 0:3 with no ramdisk.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: convert doc updates to reST]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Enable SD slot on Intel Edison platform.
By default firmware doesn't put device on active state. Thus,
we have to do this explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
This patch will enable the MUSB driver to support mass storage
devices connected to the OTG port in host mode.
Signed-off-by: Adam Ford <aford173@gmail.com>
Until now, binary TPL by Rockchip has been required for booting
procedure. Starting from this commit we may use only u-boot to boot
the device.
Note, that using binary TPL instead of U-boot TPL is still working.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable driver options for TPL/SPL in evb-rk3328_defconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit df4f40acb4 with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP
- USB 3.0, 2.0
- USB Type C power and data
- 16MB SPI Flash
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since this is part of the autoboot functionality, it makes sense to name
it with an AUTOBOOT prefix. No mainline boards use it so this should be
safe, and downstream boards will need to adjust.
Since this option is just an integer value, it really needs another option
to control whether the feature is enabled or not. Add a new
CONFIG_USE_AUTOBOOT_MENUKEY for that. This fits better with how things are
done with Kconfig, avoiding the need to use a specific value to disable
the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
-----BEGIN PGP SIGNATURE-----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=Q5fc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190731' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
This patch adds SPI and SPI_FLASH DM support for verified boot on
TI AM335 chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Built and tested on AM335x device (BeagleboneBlack).
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
This patch adds BLK and DM support for verified boot on TI AM335x
chipsets. The following compile warnings are removed:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
BLK and DM_MMC are enabled by default in SPL as well, which is
making the build to break with an overflow(spl image doesn't
fit into SRAM because of size constraints).
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 116 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
For the above reason BLK and DM_MMC is disabled in SPL.
Built and tested on AM335x device (BeagleboneBlack).
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The K3 System Controller driver is used for loading and starting
the System Firmware, and is used only on R5 SPL. It need not be
enabled and built for the A72 U-Boot and SPL, so disable it from
the j721e_evm_a72 defconfig.
While at this, also remove the unneeded CONFIG_SPL_REMOTEPROC and
CONFIG_CMD_REMOTEPROC as no remoteprocs are now loaded from A72 SPL.
Signed-off-by: Suman Anna <s-anna@ti.com>
The K3 System Controller driver is used for loading and starting
the System Firmware, and is used only on R5 SPL. It need not be
enabled and built for the A53 U-Boot and SPL, so disable it from
both the GP and HS AM65x A53 defconfigs.
While at this, also remove the unneeded CONFIG_SPL_REMOTEPROC and
CONFIG_CMD_REMOTEPROC as no remoteprocs are now loaded from A53 SPL.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The MTDPARTS currently lists just u-boot.ais as 512k in size.
This works when loading the ais file via serial port, but if one
wanted to update just the u-boot portion, it's not really possible.
This patch splits the MTDPARTS into a 32k SPL partiion and a 480k
u-boot partition which allows u-boot.img to be burned to the u-boot
partition. The remaining partitions are left with the same sizes
and offsets to not break backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
