QCS404 SoC supports two types of PHY, one supports high speed mode or
USB2 PHY and the other supports super speed mode or USB3 PHY. So add
corresponding PHY drivers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Remove the main_cpsw0_qsgmii_phyinit variable from the boot
command as there is no ethernet firmware in j721s2.
Fixes: 8886341aa6 ('configs: j721s2_evm_a72_defconfig: Add A72 specific defconfig')
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Re-sync again on some linux part, add some fixes for fsl_elbc from
Pali and switch
imx8mn bsh to use nand base ident
For nand subsystem tested on:
- imx8mn Macronix MX30LF4G18AC
- P2020 based board Turris 1.1 for fsl_elbc
- kirkwood: pogo_v4 & nsa310s: Add distro boot (Tony)
- kirkwood: add DM timer support and use it on lsxl boards (Michael)
- kirkwood: convert the Buffalo Linkstation LS-CHLv2 and XHL boards
to DM (Michael)
- mvebu: turris_mox/omnia: misc improments (Pali)
- mvebu: mbus: Fix mbus driver to work also after U-Boot relocation (Pali)
The board has only one network interface. The linux kernel will
gracefully skip a the ethernet interface if no connected PHY could be
probed. u-boot on the other hand will throw an error message. The kernel
device tree is about to be fixed. For now, just disable the ethernet
interface in our -u-boot.dtsi.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
DM_SERIAL needs early malloc. The on-chip RAM is pretty tight, it's only
2kiB, with DM_SERIAL enabled, this doesn't work anymore. Fortunately for
us, we don't need the on-chip RAM because the DRAM is already
initialized before u-boot starts. Just put the early malloc area there
and use the default early malloc size.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Just enabling the Kconfig option for DM_ETH and DM_MDIO is enough.
Additionally, we can remove the old hardcoded config.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
We still need to be able to boot legacy images. Esp. the debian
installer will have a kernel with an appended DTB.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the common kernel_addr_r, ramdisk_addr_r and fdt_addr_r variable
names.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
We can load the ramdisk as the last step. This way we don't have to set
the intermediate variable 'ramdisk_len' and can remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop our own CONFIG_FDTFILE handling in favor of the generic
CONFIG_DEFAULT_FDT_FILE one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The board code needs this to be set. Otherwise, the recovery mechanism
doesn't work. Therefore, select this option automatically with the
board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Cleanup the included header files in the board code. These are all
leftovers from earlier days.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This is not needed. The user can force setting the variables with
"setenv -f".
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The board only has a 4Mbit flash and two sectors are reserved for the
u-boot environment and the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The gpio-button driver depends on DM_GPIO, add it to Kconfig to avoid
build errors.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Add timer support for Kirkwood and MVEBU devices.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
If we switch to CONFIG_TIMER, we don't need the legacy timer macros and
functions anymore. Add the proper guards to exclude them from compiling.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_SYS_TIMER_RATE might be a dynamic value, i.e. a function call
instead of a static value, thus it has to be evaluated at runtime. If it
is a static value, the compiler should be able to optimize the unused
branches out.
This will be needed for kirkwoods dynamic CONFIG_SYS_TCLK setting.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Remove Gerald from maintainer list (email bounced)
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_UBIFS_SILENCE_MSG to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
mbus driver is initialized from arch_cpu_init() callback which is called
before relocation. This driver stores lot of functions and structure
pointers into global variables, so it is data position dependent.
Therefore after relocations all pointers are invalid and driver does not
work anymore as all pointers referes to the old memory, which overlaps with
CONFIG_SYS_LOAD_ADDR and ${loadaddr}.
For example U-Boot fuse command crashes if loadaddr memory is cleared or
rewritten by some image loaded by U-Boot load command.
mw.w ${loadaddr} 0x0 10000
fuse read 0 1 2
Fix this issue by removing of all mbus global variables in which are stored
pointers to structures or functions which changes during relocation. And
replace it by direct function calls (not via pointers). With this change
fuse command finally works.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
When Mox SFP module is connected after Topaz or Peridot module then port DT
node already contains "sfp" label. But Mox SFP module can be connected also
without Topaz or Peridot module in which case it is connected directly into
he eth1 DT node, which is without any label. So add "sfp" label into eth1
DT node in this case.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are already more MCU firmware versions for Turris Omnia in
production, so display git commit (version) of the MCU firmware during
U-Boot startup. It will help to identify what version of MCU firmware is
Turris Omnia using.
MCU firmware for Turris Omnia is open source and available at website:
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl
It can be updated from running system via i2c bus with this tool:
https://gitlab.nic.cz/turris/omnia-mcutool
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_LTO and CONFIG_UBIFS_SILENCE_MSG, and disable some
unused configs to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
Proper U-Boot removes this direct mapping. So it is available only in SPL.
This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on
32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris
Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
binman clean-up of compression and addition of utilities
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmMBd6MRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreau9wf/YQD9GsZh1HrgG5EGfaMN+NV4rGkSywZX
8AxKCscTiLVtCzUlYOEZ3mFRpli9RJ5H9eWvwcOx8GyyHkvsIdGlzdvG4PZSLd/T
bOqqtkAZxEDi0ZzQAd0bqKQ9D2ujPbatmElhBNMxyMap+Jkww7LDJvIpCKXSsGEN
881a+CafAQfYICw9TtlVLzn+WirLiIXtWMxmCuZH3hrxFVjU6T1vxoyMPIBIEzkt
SMAxRRvzjLwmYEajlDlAFwykcHJCdGbCyyoBQg1OYEIl/XZYyEN2IzdiiJFzAxn+
QA4ctAQk4gASnZfoSzTWgbeyLZqqYy8j0+z+wZaF/+dp/veZWQBLlg==
=Kn1x
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-20aug22' of https://source.denx.de/u-boot/custodians/u-boot-dm
binman fixes for various things
binman clean-up of compression and addition of utilities
- We now have a new enough sbsigntools in the distro, stop building.
- Use the 20220801 tag for Jammy.
- Move to pygit2 1.9.2 (current version) as the old one doesn't build on
"Jammy".
- Add the working directory to the list of safe directories for git.
- Move to pytest 6.2.5 to address other issues.
- This move exposed a number of minor issues in the existing scripts we
used within CI to perform the jobs themselves. The most notable changes
here involve using 'set +e / set -e' to enforce when we should or should
not make non-zero buildman status be a fatal error.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During compilation gcc throws warning:
drivers/mtd/nand/raw/fsl_elbc_nand.c: In function ‘fsl_elbc_nand_probe’:
drivers/mtd/nand/raw/fsl_elbc_nand.c:841:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return fsl_elbc_chip_init(0, (void *)dev_read_addr(dev), dev);
^
Fix it by using dev_read_addr_ptr() function which returns pointer instead
of dev_read_addr() which returns integer type.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Subpage write support for freescale eLBC NAND controller driver is
implemented in U-Boot and was fixes in the commit d3963721d9 ("nand: Sync
with Linux v4.1").
So remove NAND_NO_SUBPAGE_WRITE flag from the fsl_elbc_nand.c driver. This
partially revert commit cb04c77234 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE
to eLBC and IFC drivers"), only eLBC driver part.
With this change U-Boot with default settings can read from NAND UBIFS
image created on Linux with Linux default settings. Prior this change
U-Boot was unable to read from NAND UBIFS images created with Linux default
settings due to differnet UBI geometry.
Linux kernel fsl_elbc_nand.c driver also does not set NAND_NO_SUBPAGE_WRITE
flag and has implemented subpage write support.
Fixes: cb04c77234 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE to eLBC and IFC drivers")
Fixes: d3963721d9 ("nand: Sync with Linux v4.1")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-By: Michael Trimarchi<michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The board can mount different nand brand type. Try to use the full scan
detection and not the onfi one
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8fc82d456e40a0.
On some nand controllers with hw-ecc the controller code wants to know
the ecc strength and size and having these as 0, 0 is not accepted.
Specifying these in devicetree is possible but undesirable as the nand
may be different in different production runs of the same board, so it
is better to get this info from the nand id where possible.
This commit adds code to read the ecc strength and size from the nand
for Samsung extended-id nands. This code is based on the info for the 5th
id byte in the datasheets for the following Samsung nands: K9GAG08U0E,
K9GAG08U0F, K9GAG08X0D, K9GBG08U0A, K9GBG08U0B. These all use these bits
in the exact same way.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7bb427990ee364.
Rename the function to match this new behavior.
NOTE: fix nand_detect/nand_get_flash_type parameters in
mxs_nand_spl. This code seems never executed by any board
as alternative for nand detect
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 4722c0e958e636.
The returned "type" is never used in nand_scan_ident() and spl code
Make nand_get_flash_type() simply return an integer value in order
to avoid unnecessary ERR_PTR/PTR_ERR dance.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8cfb9ab68f9070.
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
At this point given the number of PowerPC platforms we have, a single
job to build them all fits within the time limit we have in Azure.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enforce requiring DM_ETH to be enabled for ethernet drivers, as the
migration deadline has well passed. To facilitate this, we remove some
non-migrated platforms and disable networking on a few others. Finally
we remove some of the now-useless non-DM_ETH code in some platforms as a
prerequisite for DM_ETH being set.
