This adds basic support for the Tegra2 USB controller. Board files should
call board_usb_init() to set things up.
Configuration is performed through the FDT, with aliases used to set the
order of the ports, like this fragment:
aliases {
/* This defines the order of our USB ports */
usb0 = "/usb@0xc5008000";
usb1 = "/usb@0xc5000000";
};
drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A common requirement is to find the clock ID for a peripheral. This is the
second cell of the 'clocks' property (the first being the phandle itself).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the txfilltuning
field in the EHCI controller on reset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We set up two USB ports, one of which can be host or device.
For some reason the kernel version does enable both ports.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds clock references to the USB part of the device tree for U-Boot,
and marks USB1 as supporting legacy mode (which we disable in the driver).
The USB timing information may vary between boards sometimes, but for
now we hard-code it in C. This is because all current T2x boards use
the same values, we will deal with T3x later and we first need to agree
on the format for this timing information in the fdt and may in fact
decide that it has no place there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the definition of the oscillator clock frequency and the 32KHz clock.
The latter is provided by a PMIC on I2C which we don't actually use at
present, but we expect this definition to be used in the kernel and want
to keep our .dts the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds a basic binding for the oscillator and peripheral clocks. The
second cell is the clock number, defined as the bit number within the clock
enable register if the peripheral clock.
This uses the RFC clock bindings from Grant Likely so may change later:
https://lkml.org/lkml/2011/12/12/498
It is taken from Stephen Warren's patch here:
http://patchwork.ozlabs.org/patch/141359/
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds a property to indicate a port which can switch between host and device
mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a directory to hold device tree binding files, to permit easy review
of this material in U-Boot patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
config.mk is updated to provide this file to boards through the
built-in mechanism:
/include/ ARCH_CPU_DTS
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds some support into fdtdec for reading GPIO definitions from
the fdt. We permit up to FDT_GPIO_MAX GPIOs in the system. Each GPIO
is of the form:
gpio-function-name = <phandle gpio_num flags>;
where:
phandle is a pointer to the GPIO node
gpio_num is the number of the GPIO (0 to 223)
flags is a flag, as follows:
bit meaning
0 0=polarity normal, 1=active low (inverted)
An example is:
enable-propounder-gpios = <&gpio 43 0>;
which means that GPIO 43 is used to enable the propounder (setting the
GPIO high), or that you can detect that the propounder is enabled by
checking if the GPIO is high (the fdt does not indicate input/output).
Two main functions are provided:
fdtdec_decode_gpio() reads a GPIO property from an fdt node and decodes it
into a structure.
fdtdec_setup_gpio() sets up the GPIO by calling gpio_request for you.
Both functions can cope with the property being missing, which is taken to
mean that that GPIO function is not available or is not needed.
[For reference, from Stephen Warren <swarren@nvidia.com>. It may be that
we add this extra complexity later if needed:
The correct way to parse such a GPIO property in general is:
* Read the first cell.
* Find the node referenced by the phandle (the controller).
* Ensure property gpio-controller is present in the controller node.
* Read property #gpio-cells from the controller node.
* Extract #gpio-cells from the original property.
* Keep processing more cells from the original property; there may be
multiple GPIOs listed.
According to the binding documentation in the Linux kernel, Samsung
Exynos4 doesn't use this format, and while all other chips do have a
flags cell, about 50% of the controllers indicate the cell is unused.
]
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a function to look up a property which is a phandle in a node, and
another to read a fixed-length integer array from an fdt property.
Also add a function to read boolean properties, although there is no
actual boolean type in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This fixes five trivial issues in fdtdec.c:
1. fdtdec_get_is_enabled() doesn't really need a default value
2. The fdt must be word-aligned, since otherwise it will fail on ARM
3. The compat_names[] array is missing its first element. This is needed
only because the first fdt_compat_id is defined to be invalid.
4. Added a header prototype for fdtdec_next_compatible()
5. Change fdtdec_next_alias() to only increment its 'upto' parameter
on success, to make the display error messages in the caller easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The fdtdec_find_aliases_for_id() function is complicated enough that
it really should have some tests. This does not necessarily need to be
committed to U-Boot, but it might be useful.
(note there are a few minor inconsistencies with this patch which will be
cleaned up when the USB series is applied)
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren pointed out that we should use nodes whether or not they
have an alias in the /aliases section. The aliases section specifies the
order so far as it can, but is not essential. Operating without alisses
is useful when the enumerated order of nodes does not matter (admittedly
rare in U-Boot).
This is considerably more complex, and it is important to keep this
complexity out of driver code. This patch creates a function
fdtdec_find_aliases() which returns an ordered list of node offsets
for a particular compatible ID, taking account of alias nodes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The 4.2.2 gcc in the ELDK42 release doesn't like the direct SP
load using a constant in tegra2_start. Change it to use a load
thru another reg using mov sp, %0 : : "r"(CONST).
Tested on my Seaboard T20-A03, U-Boot loads and runs OK. Also
compiled all tegra2 builds with both gcc 4.2.2 and 4.4.1 OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Ensure that transmit and receive buffers are cache-line aligned.
Invalidate cache for each packet as received, update receive buffer
descriptors one cache line at a time, flush cache before transmitting.
Original patch by Marek:
http://lists.denx.de/pipermail/u-boot/2012-February/117695.html
Signed-off-by: Eric Nelson <eric.nelson at boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This will prevent the need for architectures whose DMA alignment
is greater than 32 to have bounce buffers.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
This utilizes the newly introduced bounce buffers in the MMC layer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
This implements generic bounce buffer at the end of MMC command submission
chain. Therefore if unaligned data are passed, they are copied. This stuff
should be pushed down into the MMC subsystem to squash all places generating
these unaligned data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Building for vpac270_ond_256 configuration fails:
arch/arm/lib/libarm.o: In function `icache_disable':
/home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:156: multiple
definition of `icache_disable'
board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:65:
first defined here
arch/arm/lib/libarm.o: In function `dcache_disable':
/home/ag/git/u-boot/arch/arm/lib/cache-cp15.c:188: multiple
definition of `dcache_disable'
board/vpac270/libvpac270.o:/home/ag/git/u-boot/board/vpac270/onenand.c:66:
first defined here
make[1]: *** [/home/ag/git/u-boot/spl/u-boot-spl] Error 1
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
commit 72fa467988 moved atmel_mci_init() into
include/atmel_mci.h. Some AT91 boards are also using this interface and need
to include atmel_mci.h now.
This patch fixes MAKEALL complaints like this:
---8<---
Configuring for ethernut5 - Board: ethernut5, Options: AT91SAM9XE
ethernut5.c: In function 'board_mmc_init':
ethernut5.c:235:2: warning: implicit declaration of function 'atmel_mci_init' [-Wimplicit-function-declaration]
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Reinhard Meyer <u-boot@emk-elektronik.de>
CC: egnite GmbH <info@egnite.de>
Add support to read the boot src register and set bootcmd env from the
selected bootcmdX env setting.
Based on Linkstation boot choice selection.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Update the highbank config to use env from NVRAM. Also remove extra env
settings as they are not used unless the default env is used.
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Implement reset for highbank platform. Reset is triggered via a wfi
instruction, so enabling armv7 for the compiler is necessary.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Make some space at the beginning of RAM so the FDT can be loaded to a
known fixed address at 0x1000.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
udelay calls were off due to failing to convert us to ns. Fix this and drop
the unnecessary shifts since NS_PER_TICK is only 7ns.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The get_tbclk function was missing and the recent commit "common: add
possibility for readline_into_buffer timeout" makes it required.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Add exynos4_dmc structure in dmc.h for exynos4 dram controllor(DMC).
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This properly configures the mux to enable all UARTs.
This also fixes things so that we don't configure balls XUCTSN_1 and
XURTSN_1 as UART1 configuration (RTS/CTS), since they aren't
connected.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Chander kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch fixes the s3c24x0 timer code to work with the ARM
relocation feature.
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- change CONFIG_ENV_RANGE to contain 2 nand erase blocks,
one for bad block reserve.
- remove from the envvariable "img_writeramdisk" the
ubifsmount command, as it is not needed.
- erase the hole mtd partition containing u-boot
- save environment variable "dvn_app_vers" and "dvn_boot_vers"
only after installing the new image.
changes requested from Marek Vasut:
- arm, davinci: fix eldk-4.2 warnings for cam_enc_4xx board
- get rid of run_command2 usage
needed since patch:
commit 009dde1955
Author: Simon Glass <sjg@chromium.org>
Date: Tue Feb 14 19:59:20 2012 +0000
Rename run_command2() to run_command()
is now in mainline.
- add CONFIG_SPL_LIBGENERIC_SUPPORT support
- remove CONFIG_CMD_PXE support
- fix warning:
cam_enc_4xx.c: In function 'menu_handle':
cam_enc_4xx.c:609: warning: dereferencing type-punned pointer
will break strict-aliasing rules
- fix error:
arm-linux-ld: u-boot-spl: Not enough room for program headers,
try linking with -N
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Fletzer Martin <Martin.Fletzer@ait.ac.at>
Cc: Wolfgang Denk <wd@denx.de>
Implementation of receive-transmit mode for
omap3 MCSPI.
Introduces full duplex communication, needed by
some spi devices (such as enc28j60).
Signed-off-by: jacopo mondi <mondi@cs.unibo.it> <j.mondi@voltaelectronics.com>
Drop direct access to SOC's registers and use
the function of the GPIO driver for da8xx.
[Tom: Remove gpio[68]_base as it's now unused]
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: dzu@denx.de
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
twl4030_pmrecv_vsel_cfg currently first sets up device group (effectively
enabling the supply), and only then sets vsel (selects voltage). This could
lead to wrong voltage for a short time, or even long time if second i2c
write fails.
Fix this by writing vsel first and device group after that. Also
introduce error checking to not enable the supply if we failed to set
the voltage, and start logging errors as power supply problems are
usually important.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
