When Falcon Mode is enabled, SPL needs to check the value of
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR. Unfortunately, it was using the
CONFIG_VAL(SYS_MMCSD_RAW_MODE_ARGS_SECTOR) which converts it into
CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR when CONFIG_SPL_BUILD is
enabled. CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR does not exist in
common/spl/Kconfig. Replaced with
defined(CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR).
Signed-off-by: Elena Popa <elena.popa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MT7988 has a t-phy and an x-phy controller. There is already a driver for
t-phy so we can add USB support for this phy type.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Ethernet on Bananapi-r3 is broken after
commit bd70f3cea3 ("net: mediatek: add support for SGMII 1Gbps auto-negotiation mode")
because changes from this commit were not applied to bpi-r3 devicetree too:
commit aef54ea16c ("arm: dts: medaitek: convert gmac link mode to 2500base-x")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Builds for Raspberry Pi targets fail when CONFIG_DISPLAY_CPUINFO is
enabled and following error can be seen -
common/board_f.o:(.rodata.init_sequence_f+0x90):
undefined reference to `print_cpuinfo'
Added implementation of function "print_cpuinfo"
Signed-off-by: Naveen Kumar Chaudhary <naveenchaudhary2010@hotmail.com>
When PIE is enabled in start.S, u-boot/-spl use __rel_dyn_start
and _rel_dyn_end symbol to be loaded to and executed at a
different address than it was linked at.
u-boot-spl.lds is used in SPL build, but relocation information
section(.rela*) were discarded.
In line number 80 in arch/arm/cpu/armv8/u-boot-spl.lds
/DISCARD/ : { *(.rela*) }
If PIE enabled in SPL, __rel_dyn_start which is defined as
.rel_dyn_start in sections.c will be apended to the end of
.bss section.
In our ASPEED case, size of .bss section would let .rel_dyn_start
without 8-byte alignment, leading to alignment fault when
executing ldp instuction in pie_fix_loop.
Signed-off-by: Kevin Chen <kevin_chen@aspeedtech.com>
Since ARMv5, the clz instruction allows for efficient implementation of
ffs/fls with builtins. Until ARMv7 (with Thumb-2), this instruction is
only available in ARM mode. LTO makes it difficult to force specific
functions to be in ARM mode, as it is effectively a form of very
aggressive inlining. To work around this, fls/ffs are implemented in
assembly for ARMv5 and ARMv6 when compiling U-Boot in Thumb mode.
Overall, this saves around 75 bytes per call.
This code is synced with v5.15 of the Linux kernel.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.
- drop timer1 in favor of main_timer0 in am64-main.dtsi.
Need to delete clock & power domain properties of
main_timer1 in -r5.dts else won't boot. This is because
timer_init is done during rproc_start to start System Firmware,
but we can't do any clock/power-domain operations before
System Firmware starts.
- same constraint applies to main_uart0
- drop cpsw3g custom DT property 'mac_efuse' and custom
DT node cpsw-phy-sel as driver picks these from standard
property/node.
- include board dts file in -r5 dts file to avoid duplication
of nodes. Include -u-boot.dtsi on top.
- drop duplicate nodes in -r5 dts and -u-boot.dtsi
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This reverts commit 28a4c31134.
This node should be in the board DT file and should come from upstream.
Moreover, this PMIC is no present on all variants of am642-sk
and will need a separate board DT file.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com> #SK-AM64B
AM64-HSEVM is AM64-GPEVM with High Security Device.
Gets rid of "Unidentified board claims AM64-HSEVM in eeprom header".
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com> #SK-AM64B
To quote the author:
This series adds support for SGMII mode to the CPSW driver to enable the
functionality on TI's J7200 SoC.
Supporting SGMII mode also requires changes to the WIZ driver which acts
as a wrapper for the SerDes used by the CPSW MAC to transmit data to the
Ethernet PHY daughtercard mounted on the I2C GPIO Expander 2 connector
on the J7200 EVM.
Powering on and resetting the Ethernet PHY requires MDIO support which
is added to the CPSW driver.
For supporting DMA transactions from the MAIN CPSW instance to the A72
Host on J7200 SoC, the corresponding PSI-L endpoint information is added
for the J721E SoC, which is applicable to J7200 SoC as well.
The SGMII daughtercard used for testing SGMII mode has TI's DP83869 PHY.
Thus, enable the config for DP83869 driver functionality. Also, enable
GPIO HOG config.
The MAIN CPSW0 instance of CPSW Ethernet Switch on TI's J7200 SoC
supports SGMII mode. To enable support for utilizing the SGMII
daughtercard with TI's DP83869 PHY, enable the corresponding config.
Also, since the SGMII daughtercard is connected to the I2C GPIO
Expander 2 connector on the J7200 EVM, powering on the Ethernet PHY and
resetting it requires GPIO Hogging capability. Enable it as well.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Select the same mac divider for SGMII too as the one being used for
QSGMII.
Enable full rate divider configuration support for J721E_WIZ_10G for
SGMII.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Enhance the AM65 CPSW NUSS driver to perform a MDIO reset using a GPIO
line. Logic is also added to perform a pre and post delay around reset
using the optional 'reset-delay-us' and 'reset-post-delay-us' properties.
This is similar to the reset being performed in the Linux kernel. The
reset is done once when the CPSW MDIO bus is being initialized.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The PSIL endpoint data for J721E currently covers only the MCU domain
CPSW0 instance. Add the data for the MAIN domain CPSW0 as well to allow
the MAIN domain Ethernet ports to be usable on any platform using J721E
SoC.
Additionally, since J721E's PSIL endpoint data is applicable to J7200
SoC as well, the MAIN CPSW0 instance on J7200 will also be usable now.
Signed-off-by: Suman Anna <s-anna@ti.com>
[s-vadapalli@ti.com: Update commit message indicating support for J7200]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
- Assorted PCI-related fixes, add Apple Type-C PHY support, semihosting
updates, fix a FAT corner-case, update the help on the pxe cmd and
clean up the gpio uclass slightly.
The current gpio-uclass design uses name field in struct gpio_dev_priv as
an indicator that GPIO is claimed by consumer. This overloads the function
of name field and does not work well for named pins not configured as GPIO
pins.
Introduce separate bitfield array as the claim indicator.
This unbreaks dual-purpose AF and GPIO operation on STM32MP since commit
2c38f7c318 ("pinctrl: pinctrl_stm32: Populate uc_priv->name[] with pinmux node's name")
where any pin which has already been configured as AF could no longer be
claimed as dual-purpose GPIO. This is important for pins like STM32 MMCI
st,cmd-gpios .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a unit test for semihosting testing reading and writing a file.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
We need a platform on which we can test our semihosting code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Currently the "help" displays pxe command help text like this:
=> help
...
printenv - print environment variables
pxe - commands to get and boot from pxe files
To use IPv6 add -ipv6 parameter
qfw - QEMU firmware interface
...
This does not read clearly. Remove the IPv6 stuff as it is in
the detailed help text so that it fits just a single line.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new DM driver supporting FTPCI100 IP used in SoC designs.
This implementation is not based on the old non-DM ftpci100 code
dropped from U-Boot.
Enable the driver in sandbox_defconfig to test compilability.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
The product of two 32 bit integers is a 32 bit integer. Hence
clustcount * bytesperclust may overflow on > 4 GiB devices.
Change the type of clustcount.
Fixes: cb8af8af5b ("fs: fat: support write with non-zero offset")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This function only ever returns 0, but may not assign the second
parameter. Same thing for device_find_next_child(). Do not assign
ret to stop proliferation of this misuse.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is merely a dummy driver that makes sure the DWC3 XHCI driver
finds its reset and PHY controllers. We rely on iBoot to set up
the PHY for us.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
The Apple hardware supports 64-bit prefetchable memory windows so
enable CONFIG_SYS_PCI_64BIT. This fixes BAR assignments for the
Broadcom Ethernet controller used in some of the desktop machines.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
To quote the author:
The commit 4fcba5d556 ("regulator: implement basic reference counter")
have made it more important to keep fixed/gpio regulators enable/disable
state in balance.
This series fixes an inbalance in the mmc_dw driver and changes to use
the more relaxed regulator_set_enable_if_allowed function for a few
other drivers.
The regulator_set_enable_if_allowed function is more relaxed and will
return ENOSYS if the provided regulator is NULL or when DM_REGULATOR
was disabled. Using the following call convention should be safe:
ret = regulator_set_enable_if_allowed(<supply>, <true|false>);
if (ret && ret != -ENOSYS)
return ret;
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Disable vqmmc-supply before signal voltage is changed to keep regulator
enable counter in balance.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # P895 Tegra 3;
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Support booting ChromiumOS on ARM devices using FIT. Add an entry into the
boot implementation which does not require a command line. This can be
expanded over time as the bootm code is refactored.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootflows (such as EFI and ChromiumOS) delay reading the kernel until
it is needed to boot. This saves time when scanning and avoids needing to
allocate memory for something that may never be used.
To permit reading of these files, add a new 'bootflow read' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide an option to dump this information if available.
Move the funciion prototype to the common x86 header. Allow the command
line to be left out since 'bootflow info' show this itself and it is
not in the correct place in memory until the kernel is actually booted.
Fix a badly aligned heading while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the two new functions to separate reading of the ChromiumOS info from
the partition from actually reading the kernel and booting it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code to read the ChromiumOS information from the partition is
currently all in one function.
Create a new function which reads the kernel, assuming that the metadata
has been parsed.
For now this function is not used. Future work will plumb it in.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code to read the ChromiumOS information from the partition is
currently all in one function. It reads the entire kernel, which is
unnecessary unless it is to be booted.
Create a new function which reads just the minimum required data from the
disk, then obtains what it needs from there.
For now this function is not used. Future work will plumb it in.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths need to store their own information related to the
bootflow, in addition to the generic information in struct bootflow.
Add a pointer for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a new private structure to hold information gleaned from the disk.
This will allow separation between reading of the bootflow information and
(later) reading the whole kernel.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to avoid using #ifdefs around header files and in the code. It
makes sense to collect the various functions used for loading images into
a single header which can be included by all architectures. The best place
for this is the arch-neutral bootm.h header, so use that.
Move some zimage functions into this bootm.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a common base from which the other parts are offset and make all
of the offsets related to that. This makes the code a little easier to
read.
Use X86_ prefixes for the two values which are x86-specific.
Drop OFFSET_BASE since it is available in a header field.
Drop the unnecessary 'start' variable too.
Signed-off-by: Simon Glass <sjg@chromium.org>
