Commit graph

219 commits

Author SHA1 Message Date
Stefano Babic
569fadcd74 MPC83xx, MPC85xx: compile stub cache function
An empty flush_dcache_range() was added into MPC83xx and MPC85xx to
work with drivers shared with other architecture.  However, it is
compiled only if USB is set, but it is required for other drivers
(FSL_ESDHC), too.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Andy Fleming <afleming@gmail.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Marek Vasut <marex@denx.de>
CC: Wolfgang Denk <wd@denx.de>

Added MPC83xx version.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-21 23:37:48 +02:00
York Sun
feae34243f powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
Fix SVR checking for commit acf3f8da.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
5e23ab0a31 powerpc/mpc85xx: Workaround for erratum CPU_A011
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
48f6a5c348 powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
1e9ea85f7d powerpc/P4080: Check SVR for CPU22 workaround
Workaround for erratum CPU22 applies to P4080 rev 1 and rev 2 only.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
Prabhakar Kushwaha
e87dc41fc1 powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
During NAND_SPL boot, base address and different register are programmed
default by corresponding NAND controllers(eLBC/IFC). These settings are
sufficient enough for NAND SPL.

Avoid updating these register.They will be programmed during NAND RAMBOOT.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:31 -05:00
Prabhakar Kushwaha
d16a37b864 powerpc/85xx:Fix NAND code base to support debugger
Update NAND code base to ovecome e500 and e500v2's second limitation i.e. IVPR
+ IVOR15 should be valid fetchable OP code address.

As NAND SPL does not compile vector table so making sure IVOR + IVOR15 points to
any fetchable valid data

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:30 -05:00
Prabhakar Kushwaha
689f00fc7e powerpc/85xx:Make debug exception vector accessible
Debugging of e500 and e500v1 processer requires debug exception vecter (IVPR +
IVOR15) to have valid and fetchable OP code.

1) While executing in translated space (AS=1), whenever a debug exception is
generated, the MSR[DS/IS] gets cleared i.e. AS=0 and the processor tries to
fetch an instruction from the debug exception vector (IVPR + IVOR15); since now
we are in AS=0, the application needs to ensure the proper TLB configuration to
have (IVOR + IVOR15) accessible from AS=0 also.
Create a temporary TLB in AS0 to make sure debug exception verctor is
accessible on debug exception.

2) Just after relocation in DDR, Make sure IVPR + IVOR15 points to valid opcode

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:30 -05:00
Prabhakar Kushwaha
5344f7a258 powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
Debugging of e500 and e500v1 processer requires MSR[DE] bit to be set always.
Where MSR = Machine State register

Make sure of MSR[DE] bit is set uniformaly across the different execution
address space i.e. AS0 and AS1.

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:30 -05:00
Prabhakar Kushwaha
19a8dbdc45 powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
- BSC9131 is integrated device that targets Femto base station market.
   It combines Power Architecture e500v2 and DSP StarCore SC3850 core
   technologies with MAPLE-B2F baseband acceleration processing elements.
 - BSC9130 is exactly same as BSC9131 except that the max e500v2
   core and DSP core frequencies are 800M(these are 1G in case of 9131).
 - BSC9231 is similar to BSC9131 except no MAPLE

The BSC9131 SoC includes the following function and features:
    . Power Architecture subsystem including a e500 processor with 256-Kbyte shared
      L2 cache
    . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
    . The Multi Accelerator Platform Engine for Femto BaseStation Baseband
      Processing (MAPLE-B2F)
    . A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
     Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
     and CRC algorithms
    . Consists of accelerators for Convolution, Filtering, Turbo Encoding,
     Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
     operations
    . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
     ECC, up to 400-MHz clock/800 MHz data rate
    . Dedicated security engine featuring trusted boot
    . DMA controller
    . OCNDMA with four bidirectional channels
    . Interfaces
    . Two triple-speed Gigabit Ethernet controllers featuring network acceleration
      including IEEE 1588. v2 hardware support and virtualization (eTSEC)
    . eTSEC 1 supports RGMII/RMII
    . eTSEC 2 supports RGMII
    . High-speed USB 2.0 host and device controller with ULPI interface
    . Enhanced secure digital (SD/MMC) host controller (eSDHC)
    . Antenna interface controller (AIC), supporting three industry standard
      JESD207/three custom ADI RF interfaces (two dual port and one single port)
      and three MAXIM's MaxPHY serial interfaces
    . ADI lanes support both full duplex FDD support and half duplex TDD support
    . Universal Subscriber Identity Module (USIM) interface that facilitates
      communication to SIM cards or Eurochip pre-paid phone cards
    . TDM with one TDM port
    . Two DUART, four eSPI, and two I2C controllers
    . Integrated Flash memory controller (IFC)
    . TDM with 256 channels
    . GPIO
    . Sixteen 32-bit timers

The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.

This patch takes care of code pertaining to power side functionality only.

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:03:25 -05:00
Marek Vasut
25315683fd MPC8xxx: Define cache ops for USB
This patch conditionally defines flush_dcache_range() and
invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
resulting in the following output:

$ ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ./MAKEALL MPC8572DS
Configuring for MPC8572DS board...
make: *** [u-boot] Error 1
powerpc-linux-gnu-size: './u-boot': No such file
e1000.c: In function ‘e1000_initialize’:
e1000.c:5264:13: warning: assignment from incompatible pointer type [enabled by default]
tsec.c: In function ‘tsec_initialize’:
tsec.c:638:12: warning: assignment from incompatible pointer type [enabled by default]
drivers/usb/host/libusb_host.o: In function `ehci_td_buffer':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:186: undefined reference to `flush_dcache_range'
drivers/usb/host/libusb_host.o: In function `ehci_submit_async':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:346: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:348: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:349: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:372: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:374: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:376: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:386: undefined reference to `invalidate_dcache_range'
make: *** [u-boot] Error 1

--------------------- SUMMARY ----------------------------
Boards compiled: 1
Boards with errors: 1 ( MPC8572DS )
----------------------------------------------------------

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
2012-06-07 23:29:19 +02:00
Joe Hershberger
412411cb2e arch/powerpc/cpu/mpc85xx/ether_fcc.c: Fix compile warning
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:453:15: warning: assignment from incompatible pointer type

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-22 13:41:46 -05:00
Scott Wood
d2a97daf62 powerpc/85xx: fix NAND boot linker scripts for -fpic
GOT is now handled the way the main u-boot.lds does it.  Without this,
the boot hangs when built with newer GCC (since 4.6).  Older toolchains
hid the issue by converting -fpic to -fPIC.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-05-18 17:34:39 -05:00
Timur Tabi
822ad60f1c powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but
that register does not exist on e500v1.

Signed-off-by: Timur Tabi <timur@freescale.com>
2012-04-24 23:58:34 -05:00
Liu Gang
5056c8e068 powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.

Master needs to:
	1. Set outbound SRIO windows in order to configure slave's registers
	   for the core's releasing.
	2. Check the SRIO port status when release slave core, if no errors,
	   will implement the process of the slave core's releasing.
Slave needs to:
	1. Set all the cores in holdoff by RCW.
	2. Be powered on before master's boot.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
5ffa88eca7 powerpc/corenet_ds: Master module for boot from SRIO
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.

The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image in master NOR flash.
	3. Normally boot from local NOR flash.
	4. Configure SRIO switch system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to SRIO1 or SRIO2 by RCW.
	3. RCW should configure the SerDes, SRIO interfaces correctly.
	4. Slave must be powered on after master's boot.

For the master module, need to finish these processes:
	1. Initialize the SRIO port and address space.
	2. Set inbound SRIO windows covered slave's u-boot image stored in
	   master's NOR flash.
	3. Master's u-boot image should be generated specifically by
	   make xxxx_SRIOBOOT_MASTER_config
	4. Master must boot first, and then slave can be powered on.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:32 -05:00
Prabhakar Kushwaha
5113ee706d powerpc/85xx:Fix lds for nand boot debug info
Currently "u-boot", the elf file generated via u-boot-nand.lds does not
contain required debug information i.e. .debug_{line, info, abbrev, aranges,
ranges} into their respective _global_ sections.

The original ld script line arch/powerpc/cpu/mpc85xx/start.o
KEEP(*(.bootpg)) is not entirely correct because the start.o file is already
processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will
not process start.o again for bootpg.

So Fix u-boot-nand.lds to generate these debug information.

Signed-off-by: Anmol Paralkar <b07584@freescale.com>
Signed-off-by: John Russo <John.Russo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:31 -05:00
Prabhakar Kushwaha
119a55f9cf powerpc/85xx:Avoid vector table compilation for nand_spl
NAND SPL code never compile the vector table.
So no need to setup interrupt vector table for NAND SPL.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:30 -05:00
Prabhakar Kushwaha
64829baf04 powerpc/85xx:Fix IVORs addr after vector table relocation
After relocation of vector table in SDRAM's lower address, IVORs value should
be updated with new handler addresses.

As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs
are updated with 0x100, 0x200,....f00  hard-coded values.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:30 -05:00
Prabhakar Kushwaha
a4107f8617 powerpc/85xx:Avoid hardcoded vector address for IVORs
For e500 and e500v2 architecturees processor IVPR address should be alinged on
64K boundary.

in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be
64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may
not point to an exception handler.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:30 -05:00
Ira W. Snyder
c18de0d7ae mpc85xx: support board-specific reset function
This is useful for boards which cannot be reset in the usual way for the
85xx CPU. An example is a board which can only be reset by a hardware
watchdog.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Timur Tabi
cc15df57b1 powerpc/85xx: verify the localbus device tree address before booting the OS
The localbus controller node in the device tree is typically a root node,
even though the controller is part of CCSR.  If we were to put the lbc
node under the SOC node, then the 'ranges' property in the lbc node would
translate through the 'ranges' property of the parent SOC node, and we
don't want that.

Since the lbc is a separate node, it's possible for the 'reg' property to
be wrong.  This happened with the original version of p1022ds.dts, which
used a 32-bit value in the 'reg' address, instead of a 36-bit address.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Timur Tabi
f2717b47ea powerpc/85xx: clean up and document the QE/FMAN microcode macros
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman.  Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both.  A given SOC will only have
a QE or an Fman, so this is safe.

Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND.  There's no way to know by looking at a variable how it's supposed
to be used.

In the future, the code which uploads QE firmware and Fman firmware will
be merged.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Timur Tabi
fbc20aab11 powerpc/85xx: always implement the work-around for Erratum SATA_A001
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented
only if U-Boot initializes SATA, but SATA is not initialized by default.  So
move the work-around to the CPU initialization function, so that it's always
executed on the SOCs that need it.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
York Sun
4108508a96 powerpc/85xx: Add workaround for erratum A-003474
Erratum A-003474: Internal DDR calibration circuit is not supported

Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.

Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf54

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Jia Hongtao
33c875366e powerpc/85xx: fixup flexcan device tree clock-frequency
Make the fixup matchable with dts and kernel.  Update the compatible from
"fsl,flexcan-v1.0" to "fsl,p1010-flexcan" and Change the "clock-freq"
property to "clock-frequency".  We also change flexcan frequency from
CCB-clock to CCB-clock/2 according to P1010 spec.

We now keep the old interfaces to make previous kernel work. They should
be removed in the future.

Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:05 -06:00
Kumar Gala
43f082bb7f powerpc/85xx: Add workaround for erratum CPU-A003999
Erratum A-003999: Running Floating Point instructions requires special
initialization.

Impact:
Floating point arithmetic operations may result in an incorrect value.

Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:05 -06:00
Kumar Gala
c1ee16b8e0 arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c: Fix GCC 4.6 build warning
Fix:

fsl_corenet_serdes.c: In function 'fsl_serdes_init':
fsl_corenet_serdes.c:511:8: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
fsl_corenet_serdes.c:498:18: warning: variable 'lane_prtcl' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11 07:49:01 -06:00
Kumar Gala
3d6d9c3116 arch/powerpc/cpu/mpc85xx/tlb.c: Fix GCC 4.6 build warning
Fix:

tlb.c: In function 'disable_tlb':
tlb.c:175:34: warning: variable '_mas7' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11 07:48:59 -06:00
Kumar Gala
e4c9a35d21 arch/powerpc/cpu/mpc85xx/cpu_init.c: Fix GCC 4.6 build warning
Fix:

cpu_init.c: In function 'cpu_init_r':
cpu_init.c:320:7: warning: variable 'l2srbar' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11 07:48:59 -06:00
Poonam Aggrwal
cfee584eea fsl_ifc: Fixed a bug in the erratum handling code for IFC_A003399
Wrong pointer was being used to copy code into L2SRAM.
Also removed the unreferenced variable l2srbar.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:37:25 -06:00
Kumar Gala
50cf3d17ce powerpc/85xx: Add support for Book-E MMU Arch v2.0
A few of the config registers changed definition between MMU v1.0 and
MMUv2.0.  The new e6500 core from Freescale implements v2.0 of the
architecture.

Specifically, how we determine the size of TLB entries we support in the
variable size (or TLBCAM/TLB1) array is specified in a new register
(TLBnPS - TLB n Page size) instead of via TLBnCFG.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:36:51 -06:00
Timur Tabi
72243c0194 powerpc/85xx: resize the boot page TLB before relocating CCSR
On some Freescale systems (e.g. those booted from the on-chip ROM), the
TLB that covers the boot page can also cover CCSR, which breaks the CCSR
relocation code.  To fix this, we resize the boot page TLB so that it only
covers the 4KB boot page.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:31:09 -06:00
Timur Tabi
19e4384124 powerpc/85xx: verify the current address of CCSR before relocating it
Verify that CCSR is actually located where it is supposed to be before
we relocate it.  This is useful in detecting U-Boot configurations that
are broken (e.g. an incorrect value for CONFIG_SYS_CCSRBAR_DEFAULT).
If the current value is wrong, we enter an infinite loop, which is handy
for debuggers.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:31:06 -06:00
Timur Tabi
452ad61c3f powerpc/85xx: add some missing sync instructions in the CCSR relocation code
Calls to tlbwe and tlbsx should be preceded with an isync/msync pair.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:31:02 -06:00
Timur Tabi
c2efa0aa1e powerpc/85xx: fix some comments in the CCSR relocation code
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:59 -06:00
chenhui zhao
aada81de70 powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.

Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:32 -06:00
Wolfgang Denk
cca4e4aec1 Reduce build times
U-Boot Makefiles contain a number of tests for compiler features etc.
which so far are executed again and again.  On some architectures
(especially ARM) this results in a large number of calls to gcc.

This patch makes sure to run such tests only once, thus largely
reducing the number of "execve" system calls.

Example: number of "execve" system calls for building the "P2020DS"
(Power Architecture) and "qong" (ARM) boards, measured as:
	-> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board>
	-> grep execve /tmp/foo | wc -l

	Before: After:	Reduction:
==================================
P2020DS 20555	15205	-26%
qong	31692	14490	-54%

As a result, built times are significantly reduced, typically by
30...50%.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Albert Aribaud <albert.aribaud@free.fr>
cc: Graeme Russ <graeme.russ@gmail.com>
cc: Mike Frysinger <vapier@gentoo.org>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Matthias Weisser <weisserm@arcor.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-11-03 20:44:58 +01:00
Timur Tabi
a836626cc4 powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-20 16:01:37 -05:00
Shengzhou Liu
f81f19fafa powerpc/85xx: Update USB device tree status based on pin settings
For P3060 and P4080, USB pins are multiplexed with other functions.
Update the device tree status for USB ports based on setting of
RCW[EC1] & RCW[EC2] which describe if pins are muxed to usb.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:37:31 -05:00
Kumar Gala
4d28db8a1e powerpc/85xx: Add support for RMan LIODN initialization
This patch is intended to initialize RMan LIODN related registers on
P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to
qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:48 -05:00
Kumar Gala
9c42ef6145 powerpc/85xx: Update device tree handling for SRIO
Update device tree handling for SRIO controller to support updated
fsl,srio device tree binding.

We handle disabling of individual ports, the whole controller, RMU, and
RMAN.  Additionally, we setup the SRIO related LIODNs in the device
tree.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:43 -05:00
Kumar Gala
1a0c64219d powerpc/85xx: Update setting of SRIO LIODNs
Properly set the LIODN values associated with SRIO controller.  On
P4080/P3060 we have an LIODN per port and one for the RMU.  On
P2041/P3041/P5020 we have 2 LIODNs per port.

Update the tables for all of these devices to properly handle both
styles.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:15 -05:00
Wolfgang Denk
7bf5228ce1 Merge branch 'master' of git://git.denx.de/u-boot-fdt
* 'master' of git://git.denx.de/u-boot-fdt:
  powerpc/85xx: use fdt_create_phandle() to create the Fman firmware phandles
  fdt: update fdt_alloc_phandle to use fdt_get_phandle
  fdt: check for fdt errors in fdt_create_phandle
  fdt: Add a do_fixup_by_path_string() function
2011-10-15 22:00:01 +02:00
Timur Tabi
a2c1229c39 powerpc/85xx: use fdt_create_phandle() to create the Fman firmware phandles
Function fdt_create_phandle() conveniently creates new phandle properties
using both "linux,phandle" and "phandle", so it should be used by all code
that wants to create a phandle.

The Fman firmware code, which embeds an Fman firmware into the device tree,
was creating the phandle properties manually.  Instead, change it to use
fdt_create_phandle().

Signed-off-by: Timur Tabi <timur@freescale.com>
2011-10-15 09:35:15 -04:00
Timur Tabi
7f92c3a275 powerpc/p3060: remove all references to RCW bits EC1_EXT, EC2_EXT, and EC3
The EC1_EXT, EC2_EXT, and EC3 bits in the RCW don't officially exist on the
P3060 and should always be set to zero.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-13 23:38:10 -05:00
Haiying Wang
34fdbdf8d9 powerpc/p3041: fixup portal config info
P3041 has 10 qman portals, we need to configure all of them:
* As there are only 4 physical cores sdest can only be 0 to 3
* We assign dqrr & frame data LIODNs for all portals so if they
  are utilized the proper mapping tables can be setup uniquely
  (PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
  assignments are tuned around an assumption of at most 5
  partitions.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-13 23:38:10 -05:00
Haiying Wang
510f28cff9 powerpc/p2041: fixup portal config info
P2041 has 10 qman portals, we need to configure all of them:
* As there are only 4 physical cores sdest can only be 0 to 3
* We assign dqrr & frame data LIODNs for all portals so if they
  are utilized the proper mapping tables can be setup uniquely
  (PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
  assignments are tuned around an assumption of at most 5
  partitions.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-13 23:38:10 -05:00
Haiying Wang
7c7bd635be powerpc/p5020: fixup portal config info
P5020 has 10 qman portals, we need to configure all of them:
* As there are only 2 physical cores sdest can only be 0 or 1
* We assign dqrr & frame data LIODNs for all portals so if they
  are utilized the proper mapping tables can be setup uniquely
  (PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
  assignments are tuned around an assumption of at most 5
  partitions.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-13 23:38:09 -05:00
Mike Frysinger
e2a53458a7 net: drop !NET_MULTI code
This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00