Commit graph

72 commits

Author SHA1 Message Date
Andrew F. Davis
9e58d4dbe3 arm: mach-keystone: Modify secure image size before copy
The size of the secure image does not include the size of the
header, subtract this out before we move the image or we grab
extra data after the image.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-07-10 14:26:05 -04:00
Cooper Jr., Franklin
e5e546aad1 ARM: k2g: Program DDRPHY_DATX8 registers via mask and value variables
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:57 -04:00
Cooper Jr., Franklin
a76a6f3e04 ARM: k2g: Program DDR PHY MR2 register with the default value
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:57 -04:00
Cooper Jr., Franklin
f8b4a2d7e2 ARM: keystone2: Add additional fields used for DDR3 configuration
Future boards will need to configure DDR3 registers in a slightly
different manner. Support this by defining additional variables and
defines that will be utilized later.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:56 -04:00
Cooper Jr., Franklin
85bfe48b0a ARM: keystone2: Allow to build with all image formats
u-boot.bin is a copy of:
u-boot-fit-dtb.bin if CONFIG_FIT_EMBED is enabled,
u-boot-dtb.bin if CONFIG_OF_SEPARATE is enabled,
u-boot-nodtb.bin if DT is not enabled.
So, use u-boot.bin to to generate keystone images instead of
u-boot-dtb.bin

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:25:55 -04:00
Ley Foon Tan
0680f1b1f7 Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 07:29:48 -04:00
Cooper Jr., Franklin
1743d040b1 ARM: keystone: Enable DM_I2C by default
Enable by default DM_I2C for all Texas Instruments Keystone 2 based
evms.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-09 09:05:13 +02:00
Lokesh Vutla
ee3c6532be ARM: keystone2: Add support for getting external clock dynamically
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 12:34:29 -04:00
Lokesh Vutla
c5f177debc ARM: k2g: Add support for dynamic programming of PLL based on SYSCLK
K2G supports various sysclk frequencies which can be
determined using sysboot pins. PLLs should be configured
based on this sysclock frequency. Add PLL configurations
for all supported sysclk frequencies.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 12:34:29 -04:00
Madan Srinivas
2ff5183fba ARM: Keystone2: Build secure images for K2
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:05 -04:00
Vitaly Andrianov
e8d740f536 arm: mach-keystone: Implements FIT post-processing call for keystone SoCs
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.

The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:04 -04:00
Tom Rini
01abae4d04 Remove various unused interrupt related code
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused.  Rather than migrate
some of these options to Kconfig we just remove the code in question.

The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context.  In these cases we rename
and move the value local to the code in question.

Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06 20:42:18 -04:00
Roger Quadros
752a8311e9 ARM: k2g: setup PRU ethernet MAC addresses
PRU ethernet MAC address range is present in the
board EEPROM. Parse it and setup eth?addr
environment variables.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:57:15 -04:00
Nishanth Menon
4361220dae ARM: K2G: DDR3: Fix up priv ID for MPU
For ECC enabled DDR, we use EDMA to reset all memory values to 0. For
K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the
case for K2G, where it is 1.

Unfortunately, ddr3 code had hard coded the privID and had missed
identification previously. Fix the same, else unforeseen behavior can
be expected in our reset of DDR contents to 0 for ECC enablement.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:10 -05:00
Andrew F. Davis
ac34286647 keystone2: Move target selection to Kconfig
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-11-28 15:10:34 -05:00
Lokesh Vutla
8b01ebd812 ARM: keystone2: PLL: Enable glitch free initialization sequence
Update the PLL initialization sequence to avoid glitches while
programming. User guide for the same is available at[1].

[1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:36 -05:00
Masahiro Yamada
43ebbfc39f ARM: keystone: rename clk_get_rate() to ks_clk_get_rate()
The KeyStone platform has its own clk_get_rate() but its prototype
is different from that of the common-clk (clk-uclass) framework.

Prefix the KeyStone specific implementation with ks_ in order to
avoid name-space conflict.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:13 -04:00
Masahiro Yamada
2846bd03ea ARM: keystone: remove declaration of unused functions
These two functions are neither defined nor referenced.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-07 14:26:35 +00:00
Lokesh Vutla
5d21406516 ARM: keystone2: Add support for parsing monitor header
Given that boot monitor image is being generated to a specific target location
depending on the SoC and U-boot relies on addr_mon env variable to be aligned
with boot monitor target location. When ever the target address gets updated in
boot monitor, it is difficult to sync between u-boot and boot monitor and also
there is no way to update user that boot monitor image is updated.

To avoid this problem, boot monitor image is being generated with mkimage
header. Adding support in mon_install command for parsing this header.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:10 -04:00
Lokesh Vutla
e1ae357d4b board: k2g: Enable ECC byte lane
Enable ECC byte lane for k2g-evm

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:07 -04:00
Masahiro Yamada
5d97dff042 treewide: replace #include <asm-generic/errno.h> with <linux/errno.h>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.

<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 22:25:27 -04:00
Karicheri, Muralidharan
bcdc1c8376 keystone: k2h/e/l: Fix DMA coherency for QM PDSP
commit 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid
left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid.
This, in effect disabled DMA coherency for QM PDSP.

Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs,
the #ifdef should been removed in the first place. Do the same.

Fixes: 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25 12:00:05 -04:00
Lokesh Vutla
e2924e5904 ARM: k2g: Configure reset mux to device reset
BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM.
Timer5(dedicated to ARM) when used as WatchDog timer, the events it
generates are routed to the above mux.

Following are the 3 events that can controlled bt the reset mux:
- Device Reset
- An interrupt to the ARM_GIC
- An interrupt to the ARM_GIC followed by a device reset.

Right now to give a default watchdog behaviour "Device reset" is
being selected.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
2016-06-02 21:42:19 -04:00
Nishanth Menon
2283284b05 ARM: keystone2: Add missing privilege ID settings
Add missing Privilege ID settings for KS2 SoCs.

Based on:
K2H/K: Table 6-7. Privilege ID Settings from SPRS866E (Nov 2013)
  http://www.ti.com/lit/ds/symlink/66ak2h14.pdf (page 99)
K2L: Table 7-7. Privilege ID Settings from SPRS930 (April 2015)
  http://www.ti.com/lit/ds/symlink/66ak2l06.pdf (page 71)
K2E: Table 7-7. Privilege ID Settings from SPRS865D (Mar 2015)
  http://www.ti.com/lit/ds/symlink/66ak2e05.pdf (page 75)
K2G: Table 3-16. PrivIDs from SPRUHY8 (Jan 2016)
  http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf (page 238)

Overall mapping:
-------+-----------+-----------+-----------+---------
PrivID | KS2H/K    | K2L       | K2E       | K2G
-------+-----------+-----------+-----------+---------
0      | C66x 0    | C66x 0    | C66x 0    | C66x 0
1      | C66x 1    | C66x 1    | Reserved  | ARM
2      | C66x 2    | C66x 2    | Reserved  | ICSS0
3      | C66x 3    | C66x 3    | Reserved  | ICSS1
4      | C66x 4    | Reserved  | Reserved  | NETCP
5      | C66x 5    | Reserved  | Reserved  | CPIE
6      | C66x 6    | Reserved  | Reserved  | USB
7      | C66x 7    | Reserved  | Reserved  | Reserved
8      | ARM       | ARM       | ARM       | MLB
9      | NetCP     | NetCP     | NetCP     | PMMC
10     | QM_PDSP   | QM_PDSP   | QM_PDSP   | DSS
11     | PCIe_0    | PCIe_0    | PCIe_0    | MMC
12     | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP
13     | Reserved  | Reserved  | PCIe_1    | Reserved
14     | HyperLink | PCIe_1    | HyperLink | Reserved
15     | Reserved  | Reserved  | TSIP      | Reserved
-------+-----------+-----------+-----------+---------

NOTE: Few of these might have default configurations, however,
since most are software configurable, it is better to explicitly
configure the system to have a known default state.

Without programming these, we end up seeing lack of coherency on certain
peripherals resulting in inexplicable failures (such as USB peripheral's
DMA data not appearing on ARM etc and weird workarounds being done by
drivers including cache flushes which tend to have system wide
performance impact).

By marking these segments as shared, we also ensure SoC wide coherency
is enabled.

Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:17:40 -04:00
Nishanth Menon
1f807a9f32 ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery
MSMC segment Privilege ID is not consistent accross the keystone2 SoCs.
As the first step to ensure complete SoC wide coherency setup, lets
refactor the macros to remove the #if-deffery around the code which
obfuscates which IDs are actually enabled for which SoC.

As a result of this change the PCIe configuration is moved after the
msmc configuration is complete, but that should ideally have no
functional impact.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:17:40 -04:00
Nishanth Menon
705c506e4f ARM: keystone2: Convert BOOT_SET_BITFIELD into static inline function
Fix up BOOT_SET_BITFIELD to be a static inline function to be readable
with the same functionality.

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:11 -04:00
Nishanth Menon
f84e8e5b29 ARM: keystone2: Convert BOOT_READ_BITFIELD into static inline function
BOOT_READ_BITFIELD can easily be a static inline function and be a
little more readable with the same functionality.

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:11 -04:00
Nishanth Menon
bc69b505f0 ARM: keystone2: Convert BOOTBITMASK to static inline function
BOOTBITMASK is almost impossible to decode, so convert it into a simpler
static line functions of equivalent solution.

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:10 -04:00
Tom Rini
80485af243 ARM: keystone2: Only link cmd_ddr3.o on non-SPL builds
When we switch to including all linker lists in SPL it is important
to not include commands as that may lead to link errors due to other
things we have already discarded.  In this case simply move cmd_ddr3.o
over to the list with the rest.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:34 -04:00
Tom Rini
534bc70e35 ARM: keystone2: Switch to using the poweroff command
Now that we have a standard way to power off the hardware, switch to
using that rather than our own command.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:32 -04:00
Tom Rini
aadd3360e6 ARM: keystone2: Split monitor code / command code
When we switch to including all linker lists in SPL it is important
to not include commands as that may lead to link errors due to other
things we have already discarded.  In this case, we split the code for
supporting the monitor out from the code for loading it.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:15 -04:00
Vitaly Andrianov
8efc243741 ARM: keystone2: use detected ddr3a size
Because KS2 u-boot works in 32 bit address space the existing ram_size
global data field cannot be used. The maximum, which the get_ram_size()
can detect is 2GB only. The ft_board_setup() needs the actual ddr3 size
to fix up dtb.

This commit introduces the ddr3_get_size() which uses SPD data to
calculate the ddr3 size. This function replaces the "ddr3_size"
environment variable, which was used to get the SODIMM size.

For platforms, which don't have SODIMM with SPD and ddr3 is populated to
a board a simple ddr3_get_size function that returns ddr3 size has to be
implemented. See hardware-k2l.h

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:45 -04:00
Vitaly Andrianov
d9a76e77c8 ARM: keystone2: use SPD info to configure K2HK and K2E DDR3
This commit replaces hard-coded EMIF and PHY DDR3 configurations for
predefined SODIMMs to a calculated configuration. The SODIMM parameters
are read from SODIMM's SPD and used to calculated the configuration.

The current commit supports calculation for DDR3 with 1600MHz and 1333MHz
only.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:44 -04:00
Lokesh Vutla
ef76ebb1ef ARM: keystone2: K2G: Add support for different arm/device speeds
The maximum device and arm speeds can be determined by reading
EFUSE_BOOTROM register. As there is already a framework for reading this
register, adding support for all possible speeds on k2g devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:44 -04:00
Lokesh Vutla
5cd1f6bd7a ARM: keystone2: Allow for board specific speed definitions
Its not compulsory that speed definition should be same on EFUSE_BOOTROM
register for all keystone 2 devices. So, allow for board specific
speed definitions.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:43 -04:00
Suman Anna
f2a8279e76 ARM: keystone2: K2G: power-off DSP during boot
The DSPs are powered on by default upon a Power ON reset, and
they are powered off on current Keystone 2 SoCs - K2HK, K2L, K2E
during the boot in u-boot. This is not functional on K2G though.
Extend the existing DSP power-off support to the only DSP present
on K2G. Do note that the PSC clock domain module id for DSP on K2G
differs from that of previous Keystone2 SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:43 -04:00
Suman Anna
4ed8b2c969 ARM: keystone2: Use macro for DSP GEM power domain
Define a macro for the DSP GEM power domain id number and
use it instead of a hard-coded number in the code that
disables all the DSPs on various Keystone2 SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:42 -04:00
Nishanth Menon
ec00b2e3ab ARM: keystone2: psc: introduce function to hold and release module in reset.
These are useful for modules that need to be held in reset and are
enabled for data to be loaded on to them. Typically these are
microcontrollers or other processing entities in the system.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:36 -04:00
Nishanth Menon
7ca12b9700 ARM: keystone2: psc-defs: use adequate () for macros
'#define X a | b' is better defined as '#define X (a | b)' for obvious
reasons.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:36 -04:00
Nishanth Menon
82ff21bd6f ARM: keystone2: psc: redo doc in kernel-doc format
u-boot coding style guidance in
http://www.denx.de/wiki/U-Boot/CodingStyle clearly mentions that the
kernel doc style shall be followed for documentation in u-boot.

Current PSC documentation standard does not, so fix that.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:36 -04:00
Nishanth Menon
239c6953a9 ARM: keystone2: Get rid of unused clock files
With commit fe772ebd28 ("ARM: keystone2: Use common definition for
clk_get_rate"), we have centralized the clock code into a common clock
logic and the redundant files, unfortunately remained... Clean that
up.

Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:35 -04:00
Roger Quadros
3b68939fa0 ARM: k2g: add SD card and eMMC support
Add MMC support for k2g

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22 14:22:25 -04:00
Vitaly Andrianov
cddb330035 ARM: k2g: update keystone nav rx queue numbers
update K2G nav rx queue number

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:21 -04:00
Vitaly Andrianov
11d8222a26 ARM: k2g: Correct base addresses
Coreect base addresses for SPI, Queue Manager, Ethernet, GPIO,
and MSMC segments.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:20 -04:00
Vitaly Andrianov
5dd6af2ecb ARM: k2g: Add support for pin mux configuration
Add api for configuring pin mux.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:19 -04:00
Vitaly Andrianov
235dd6e8d1 ARM: k2g: Add ddr3 info
Add ddr3 related info

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:18 -04:00
Vitaly Andrianov
0fba27b690 ARM: k2g: Add PSC info
Add psc information for k2g

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:17 -04:00
Vitaly Andrianov
e6d71e1ca5 ARM: k2g: Add clock information
Add clock information for Galileo

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22 14:22:16 -04:00
Vitaly Andrianov
bda920c65e ARM: k2g: Add pll data
Add pll data for k2g

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:15 -04:00
Lokesh Vutla
f9c4a51c3e ARM: k2g: Add kconfig support
Add Kconfig support

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:13 -04:00