Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the same approach as ROC-RK3328-CC which enables SPL GPIO,
pinctl and regulator support. This allows the gen3 board to
boot through SPL and does not break gen2 in the process.
Signed-off-by: Kurt Miller <kurt@intricatesoftware.com>
Acked-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The USB PHYs on the RK3328 aren't supported, nor are any other generic
PHYs. Because upstream Linux device trees already include the USB PHYs
and references in the USB hosts, this would result in various calls
to the generic PHY API to fail.
Instead, just disable generic PHY support for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This enables reading of the cpuid and a static MAC address.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
Select CONFIG_FASTBOOT_FLASH, CONFIG_FASTBOOT_FLASH_MMC_DEV
for rockchip SoC plaforms in fastboot Kconfig file instead
of defined it in board defconfig.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip support differnet or common gadget product number
between Rockchip SoCs like,
0x310a - rk3036
0x320a - rk3229, rk3288
0x330a - rk3328
So, select them on Kconfig based on platform specific
config defined.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.
So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.
This eventually drop the explicit defined added
on supported board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The mode selection for the DWC3 is kind of obsolete. The driver does not
have to be host only or gadget only. This choice is confusing.
All the remaining callers of dwc3_uboot_init() explicitly set dr_mode
before calling the function, so none rely on a default behavior.
Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it
by default if USB_GADGET and USB_DWC3 are enabled.
It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and
DWC3 for the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Until now, binary TPL by Rockchip has been required for booting
procedure. Starting from this commit we may use only u-boot to boot
the device.
Note, that using binary TPL instead of U-boot TPL is still working.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK64 is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
This series allow building u-boot SPL and u-boot.itb for Rock64
board. The proprietary TPL is stil required for deploy:
./tools/mkimage -n rk3328 -T rksd \
-d ./rkbin/bin/rk33/rk3328_ddr_333MHz_v1.16.bin idbloader.img
cat ./spl/u-boot-spl.bin >> idbloader.img
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
