Linux-arm64 require that CNTVOFF_EL2 should be programmed with
a consistent value on all cpus. Initializing CNTVOFF_EL2 at state
transition instead of start.S could prevent potential different value
on cpus if ATF exist and u-boot runs at only one cpu.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
This commit copies implementation of the find_next_zero_bit() from
git://git.denx.de/u-boot.git/arch/mips/include/asm/bitops.h. v2014.07
The function is required to enable MCAST_TFTP support for ARM platforms.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
The "fastboot reboot-bootloader" command is defined to
re-enter into fastboot mode after rebooting into
bootloader. This command is usually used after updating
bootloader via fastboot.
This commit implements only a generic side of the
command - setting of the reset flag and then resetting.
Setting of the reset flag is implemented using __weak
fb_set_reboot_flag() function. The actual setting and
checking of the reset flag should be implemented by
a boot script and/or board/SoC specific code.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
Implement an alias name check for devices where GPT limitations prevent
user-friendly partition names such as "boot", "system" and "cache". Or,
where the actual partition name doesn't match a standard partition name
used commonly with fastboot.
To set an alias, add an environment setting as follows:
fastboot_partition_alias_<alias partition name>=<actual partition name>
Example: fastboot_partition_alias_boot=LNX
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Cc: Steve Rae <srae@broadcom.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
trigger watchdog before calling usb_gadget_handle_interrupts()
This prevents board resets when calling dfu command on boards
which have a watchdog.
Signed-off-by: Heiko Schocher <hs@denx.de>
[ Reedition by Lukasz Majewski <l.majewski@samsung.com> to apply to
v2014.04 release ]
USB Mass Storage is the standard name, so let's use it here.
Suggested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
For u-boot dwc3 driver the scatter gather list support has been removed
from original linux code. It is correct, since we try to send one request
at a time.
However, the cleanup left spurious break, which caused early exit from
loop at dwc3_cleanup_done_reqs() function. As a result the dwc3_gadget_giveback()
wasn't called and caused USB Mass Storage to hang.
This commit removes this problem and refactor the code to remove superfluous
do { } while(1) loop.
Test HW: Odroid XU3 (with ./test/ums/ums_gadget_test.sh)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Commit "drivers/dwc3: add a workaround for too small OUT requests"
sets max packet for OUT requests when transfer is smaller.
Until this change the default maxpacket for non EP0 EPs was 1024. This is
too much, since UMS LBA size is 512B
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
It turned out that current dwc3 gadget code is preparing multiple TRBs
for a transfer. Unfortunately, when multiple requests are in the same
queue, only for the last one the LST (last) ctrl bit is set.
Due to that dwc3 HW executes all TRBs up till the one marked as last.
Unfortunately, UMS requires call of ->complete callback after any send TRB.
This is the reason for "hangs" in executing UMS.
This code simplifies this situation and set each TRB's ctrl field bit to be
last (LST bit).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
There is no point in calling dwc3_thread_interrupt() if no event is
pending. There is also no point in flushing event cache in EVERY loop
iteration.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch adds code to select standard, commonly used usb endpoint
configuration (ep1in-bulk, ep2out-bulk, ep3in-int) to dwc3 driver. This
ensures compatibility with old userspace and windows drivers, which
expects hardcoded endpoint numbers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
DWC3 hangs on OUT requests smaller than maxpacket size,
so HACK the request length to be at least equal to maxpacket size.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This commit makes the dwc3_set_mode() as static, to prevent collisions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The BIT() macro is used only in those places, so it is reasonable to
replace it by a constant value.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
DWC3 UDC driver requires presence of .reset callback in a composite driver.
This setting is similar to the one nowadays present in linux kernel.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This patch invokes board-specific USB cleanup (board_usb_cleanup)
function in the mass storage gadget
Signed-off-by: Inha Song <ideal.song@samsung.com>
Since we support multiple dwc3 controllers to be existent at the same
time, in order to handle the interrupts of a particular dwc3 controller
usb_gadget_handle_interrutps should take controller index as an
argument.
Hence the API of usb_gadget_handle_interrupts is modified to take
controller index as an argument and made the corresponding changes to all
the usb_gadget_handle_interrupts calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in am43xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in dra7xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Invoked board_usb_cleanup for cleaning up initialized USB. It
will be invoked if the user enterts ctrl-C.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Taken from linux kernel with commit
commit 765f5b830e547229bb752e7b232ee83e2b3d49d5
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date: Thu Jun 23 14:26:11 2011 +0200
usb: gadget: defer setting maxpacket till ->setup()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Now that the entire dwc3 driver is adapted to compile with uboot build,
modify the Makefiles so that the dwc3 driver can be built.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
dwc3 can do only max packet aligned transfers. So in case request length
is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE
two chained TRBs is required to handle the transfer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
No functional change. Modified few things so that there are no
code duplication while implementing chained TRB.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
In the linux kernel, non cacheable buffers are used. However in uboot
since there are no APIs to allocate non cacheable memory, all
the buffers should be flushed before using it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Added a single driver for both USB2 PHY programming and USB3 PHY
programming.
USB3 PHY is taken from drivers/phy/phy-ti-pipe3.c in linux kernel.
commit 56042e : phy: ti-pipe3: Fix suspend/resume and module reload.
USB2 PHY is taken from drivers/phy/phy-omap-usb2.c in linux kernel.
commit eb82a3 : phy: omap-usb2: Balance pm_runtime_enable() on probe
failure and remove.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added an API to check for interrupt status. This API is generally
called from board file to check for interrupt status.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added support for multiple dwc3 omap controllers. This gives uboot
the capability to control multiple dwc3 omap controllers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Removed probe and remove that are specific to linux and replaced it with
uboot init and uboot exit. These functions will be invoked from boardfile.
This will change once we have dwc3-omap driver adapted to use the uboot
driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a structure to populate dwc3 omap platform data. The board file should
populate these platform data before invoking dwc3 omap driver.
This will be removed once dwc3-omap driver is adapted to use the driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
*) Changed the included header files to that used in u-boot.
*) Removed extcon_* APIs
*) Removed regulator_* APIs
*) Fixed other misc warnings
*) Added dwc3-omap.h to include the definitions of UTMI modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Since interrupt support is not present in u-boot, added an
API to handle the interrupts in dwc3 core. This API can be
polled to handle the interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added support for multiple dwc3 controllers. This gives uboot
the capability to control multiple dwc3 controllers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Removed probe and remove that are specific to linux and replaced it with
uboot init and uboot exit. These functions will be invoked from boardfile.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a structure to populate dwc3 core platform data. The board file should
populate these platform data before invoking dwc3 driver.
This will be removed once we have dwc3 driver adapted to use the driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
*) Changed the include header files to that used in u-boot.
*) Removed phy_* APIs
*) Removed jiffies and used a simple while loop
*) Used dma_alloc_coherent and dma_free_coherent APIs of u-boot
*) Fixed other misc warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added USB_GADGET_DELAYED_STATUS to avoid the following compilation error.
error: ‘USB_GADGET_DELAYED_STATUS’ undeclared (first use in this function)
while compiling dwc3/ep0.c
While this is been added only to avoid compilation error, the complete fix
should be something like the one added in linux kernel. The complete fix
will be ported once we have the composite driver in u-boot look similar to
the one in linux kernel.
commit 1b9ba000177ee47bcc5b44c7c34e48e735f5f9b1
Author: Roger Quadros <roger.quadros@nokia.com>
Date: Mon May 9 13:08:06 2011 +0300
usb: gadget: composite: Allow function drivers to pause control transfers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
*) Changed the included header files to that used in u-boot.
*) added dwc3_ep_event_string() used in ep0.c
*) Fixed other misc warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added resource_size_t type in order to get rid of the following
compilation error whiel building dwc3 gadget.
include/linux/ioport.h:19:2: error: unknown type name ‘resource_size_t’
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Did a bunch of things to get dwc3/gadget.c compile in u-boot without
build errors and warnings
*) Changed the included header files to that used in u-boot.
*) Used dma_alloc_coherent and dma_free_coherent APIs of u-boot
*) removed sg support
*) remove jiffies and used a simple while loop
*) removed irq support and added a function to call these interrupt handler.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a header file to include various linux specific APIs like
pr_debug, WARN_ WARN_ON_ONCE etc.. in order to avoid compilation
error while building dwc3 driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
