This option will provide the offset in the parallel NOR flash memory to,
which the falcon boot data is stored.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit makes the CMD_SPL_NAND_OFS only visible when we use NAND
memory.
Before this change it was present when only CMD_SPL was enabled (and
would stay when board with other falcon boot medium is used).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
this patch adds basic changes for adding a erase-subcommand to env
with this command the environment stored on non-volatile storage written
by saveenv can be cleared.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
squashed fixes
- start message with "Erasing"
- mark erase-function as optional
- env: separate eraseenv from saveenv
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.
With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add sub-command 'env info' to display environment information:
- env_valid : is environment valid
- env_ready : is environment imported into hash table
- env_use_default : is default environment using
This command can be optionally used for evaluation in scripts:
[-d] : evaluate whether default environment is used
[-p] : evaluate whether environment can be persisted
The result of multiple evaluations will be combined with AND.
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Do not enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
'Bootloader Control Block' (BCB) is a well established term/acronym in
the Android namespace which refers to a location in a dedicated raw
(i.e. FS-unaware) flash (e.g. eMMC) partition, usually called "misc",
which is used as media for exchanging messages between Android userspace
(particularly recovery [1]) and an Android-capable bootloader.
On higher level, this allows implementing a subset of Android Bootloader
Requirements [2], amongst which is the Android-specific bootloader
flow [3]. Regardless how the latter is implemented in U-Boot ([3] being
the most memorable example), reading/writing/dumping the BCB fields in
the development process from inside the U-Boot is a convenient feature.
Hence, make it available to the users.
Some usage examples of the new command recorded on R-Car H3ULCB-KF
('>>>' is an overlay on top of the original console output):
=> bcb
bcb - Load/set/clear/test/dump/store Android BCB fields
Usage:
bcb load <dev> <part> - load BCB from mmc <dev>:<part>
bcb set <field> <val> - set BCB <field> to <val>
bcb clear [<field>] - clear BCB <field> or all fields
bcb test <field> <op> <val> - test BCB <field> against <val>
bcb dump <field> - dump BCB <field>
bcb store - store BCB back to mmc
Legend:
<dev> - MMC device index containing the BCB partition
<part> - MMC partition index or name containing the BCB
<field> - one of {command,status,recovery,stage,reserved}
<op> - the binary operator used in 'bcb test':
'=' returns true if <val> matches the string stored in <field>
'~' returns true if <val> matches a subset of <field>'s string
<val> - string/text provided as input to bcb {set,test}
NOTE: any ':' character in <val> will be replaced by line feed
during 'bcb set' and used as separator by upper layers
=> bcb dump command
Error: Please, load BCB first!
>>> Users must specify mmc device and partition before any other call
=> bcb load 1 misc
=> bcb load 1 1
>>> The two calls are equivalent (assuming "misc" has index 1)
=> bcb dump command
00000000: 62 6f 6f 74 6f 6e 63 65 2d 73 68 65 6c 6c 00 72 bootonce-shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The output is in binary/string format for convenience
>>> The output size matches the size of inspected BCB field
>>> (32 bytes in case of 'command')
=> bcb test command = bootonce-shell && echo true
true
=> bcb test command = bootonce-shell- && echo true
=> bcb test command = bootonce-shel && echo true
>>> The '=' operator returns 'true' on perfect match
=> bcb test command ~ bootonce-shel && echo true
true
=> bcb test command ~ bootonce-shell && echo true
true
>>> The '~' operator returns 'true' on substring match
=> bcb set command recovery
=> bcb dump command
00000000: 72 65 63 6f 76 65 72 79 00 73 68 65 6c 6c 00 72 recovery.shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The new value is NULL-terminated and stored in the BCB field
=> bcb set recovery "msg1:msg2:msg3"
=> bcb dump recovery
00000040: 6d 73 67 31 0a 6d 73 67 32 0a 6d 73 67 33 00 00 msg1.msg2.msg3..
00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
>>> --- snip ---
>>> Every ':' is replaced by line-feed '\n' (0xA). The latter is used
>>> as separator between individual commands by Android userspace
=> bcb store
>>> Flush/store the BCB structure to MMC
[1] https://android.googlesource.com/platform/bootable/recovery
[2] https://source.android.com/devices/bootloader
[3] https://patchwork.ozlabs.org/patch/746835/
("[U-Boot,5/6] Initial support for the Android Bootloader flow")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
In order to use CMD_SF / CMD_SPI / ENV_IS_IN_SPI_FLASH we need to have
the SPI (or SPI_FLASH/DM_SPI_FLASH, for CMD_SF) enabled. Express this
in the Kconfigs.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Compiling the display command leads to an error
undefined reference to `display_set'
No implementation of display_set() exists in U-Boot.
Eliminate the `display` command as well as the accompanying files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device path to text protocol is not needed for EBBR compliance. So
let's make it a customizable option.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There is no 'config CRC32', remove the select that was attempting to use
it.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds booti support for RISC-V Linux kernel. The existing
bootm method will also continue to work as it is.
It depends on the following kernel patch which adds the header to the
flat Image. Gzip compressed Image (Image.gz) support is not enabled with
this patch.
https://patchwork.kernel.org/patch/10925543/
Tested on HiFive Unleashed and QEMU.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Karsten Merker <merker@debian.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This reverts commit 65a97e7fcf.
The 'eeprom' command has been converted to work with DM_I2C in a patch
submitted around the same time as this commit:
commit 0c07a9b407 ("eeprom: Add device model based I2C support to eeprom command")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
When using boot scripts it can become quite hard to understand
which commands are actually executed during bootup (e.g. where
is a kernel image loaded from or which DTB is in use).
Shell scripts suffer from a similar problem and many shells address
this problem with a command execution tracer (e.g. BASH has xtrace,
which can be enabled by "set -x").
This patch introduces a command tracer for U-Boot, which prints
every command with its arguments before it is executed.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The 'exception' command allows to test exception handling.
This implementation supports ARM, x86, RISC-V and the following exceptions:
* 'breakpoint' - prefetch abort exception (ARM 32bit only)
* 'unaligned' - data abort exception (ARM only)
* 'undefined' - undefined instruction exception
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a command to control the watchdog devices. This is useful if the
watchdog is rather long running (eg. seconds) and it should be
controlled by scripts. It is also handy during debugging.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, there is no easy way to add or modify UEFI variables.
In particular, bootmgr supports BootOrder/BootXXXX variables, it is
quite hard to define them as u-boot variables because they are represented
in a complicated and encoded format.
The new command, efidebug, helps address these issues and give us
more friendly interfaces:
* efidebug boot add: add BootXXXX variable
* efidebug boot rm: remove BootXXXX variable
* efidebug boot dump: display all BootXXXX variables
* efidebug boot next: set BootNext variable
* efidebug boot order: set/display a boot order (BootOrder)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"env [print|set] -e" allows for handling uefi variables without
knowing details about mapping to corresponding u-boot variables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Without CONFIG_LED, we get
cmd/built-in.o: In function `show_led_state':
cmd/led.c:40: undefined reference to `led_get_state'
cmd/built-in.o: In function `do_led':
cmd/led.c:99: undefined reference to `led_get_by_label'
cmd/led.c:108: undefined reference to `led_set_state'
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
It should not be necessary to adjust CMD_BOOTEFI_HELLO_COMPILE in config
files.
arch/arm/lib/crt0_arm_efi.S cannot be compiled in thumbs mode. We can
disable CMD_BOOTEFI_HELLO_COMPILE for CONFIG_CPU_V7M. So there is no longer
a need to disable it in stm32 configs.
helloworld.efi can be built without problems on x86_64. So there is no need
to disable it in chromebook_link64_defconfig and qemu-x86_64_defconfig.
Same is true for ARM V7A. So do not disable CMD_BOOTEFI_HELLO_COMPILE in
kp_imx6q_tpc_defconfig.
Some architecture checks are already make for EFI_LOADER. There is no need
to repeat them for CMD_BOOTEFI_HELLO_COMPILE
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice.Chotard@st.com
Signed-off-by: Alexander Graf <agraf@suse.de>
The implementation of the EEPROM commands does not support the DM I2C API.
Prevent compilation breakage by not enabling it if the non-DM API is not
available (if DM_I2C is used without DM_I2C_COMPAT)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add common clear screen command for configurations
CONFIG_DM_VIDEO, CONFIG_LCD and CONFIG_CFB_CONSOLE.
Remove the existing cls command implementation from
lcd.c code and activate the command for all boards
enabling CONFIG_LCD for compatibility reasons.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Patrick.Delaunay <patrick.delaunay@free.fr>
pinmux command allows to :
- list all pin-controllers available on platforms
- select a pin-controller
- display the muxing of all pins of the current pin-controller
or all pin-controllers depending of given options
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
cmd: pinmux: Fix pinmux command
if "pinmux status" command is used without having
set dev using "pinmux dev", print pinmux usage
Reviewed-by: Simon Glass <sjg@chromium.org>
Add 'virtio' command in U-Boot command line.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit c58fb2cdb3 ("cmd: ubi: clean the partition handling")
introduced a call to mtd_probe_devices() in the ubi_attach() path
and this function takes care of parsing mtdparts/mtdids and
creating/registering the associated mtd partitions.
The mtdparts_init() call in the ubi_detach() path is not only
unnecessary but can sometimes print error messages even when things
work properly (that's the case with SPI NAND devices that have not
been probed with 'mtd list'), which is misleading.
Remove this call to mtdparts_init() and drop the dependency on
CMD_MTDPARTS.
Fixes: c58fb2cdb3 ("cmd: ubi: clean the partition handling")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
gwventana configs are relying on CMD_UBI to select CMD_MTDPARTS,
which is then making {MTDIDS,MTDPARTS}_DEFAULT options available.
We are about to remove the 'select CMD_MTDPARTS' statement in the
CMD_UBI entry, but if we do that without first making sure
{MTDIDS,MTDPARTS}_DEFAULT are visible, we end up with a build
failure when building gwventana configs.
Address that by adding a depends on MTD_PARTITIONS to
{MTDIDS,MTDPARTS}_DEFAULT which does the trick since CMD_UBI selects
MTD_UBI which in turn selects MTD_PARTITIONS.
We also get rid of the depends on CMD_MTD, since CMD_MTD also selects
MTD_PARTITIONS.
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'mtdparts' command is not needed anymore. While the environment
variable is still valid (and useful, along with the 'mtdids' one), the
command has been replaced by 'mtd' which is much more close to the MTD
stack and do not add its own specific glue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI should not mess with MTD partitions, now that the partitions are
handled in a clean way, clean the ubi command and avoid using this
uneeded extra-glue to reference the devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Previously poweroff was located under boot. It seems to make more
sense to have it located under the Device access commands.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add basic command for bus information and read for onewire
bus using Dallas 1-Wire protocol.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add command to query information from and write text to on-screen
display (OSD) devices.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'conitrace' command prints the codes received from the console input as
hexadecimal numbers.
This developer utility is useful for testing the handling of special keys
by keyboard drivers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It is not preferred to put SUNXI-specific code in the common place.
Change it to 'imply' property of ARCH_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In some cases it can be useful to be able to bind a device to a driver from
the command line.
The obvious example is for versatile devices such as USB gadget.
Another use case is when the devices are not yet ready at startup and
require some setup before the drivers are bound (ex: FPGA which bitsream is
fetched from a mass storage or ethernet)
usage example:
bind usb_dev_generic 0 usb_ether
unbind usb_dev_generic 0 usb_ether
or
unbind eth 1
bind /ocp/omap_dwc3@48380000/usb@48390000 usb_ether
unbind /ocp/omap_dwc3@48380000/usb@48390000
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
dtimg command allows user to work with Android DTB/DTBO image format.
Such as, getting the address of desired DTB/DTBO file, printing the dump
of the image in U-Boot shell, etc.
This command is needed to provide Android boot with new Android DT image
format further.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Trivial Kconfig cleanup. Use tabs instead of spaces and every Kconfig
entry should be separated by newline.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
1. Since libavb library alone is highly portable, introduce dedicated
Kconfig symbol for AVB bootloader-dependent operations, so it's possible
to build libavb separately. AVB bootloader-dependent operations include:
* Helpers to process strings in order to build OS bootargs.
* Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c.
* Helpers to alloc/init/free avb ops.
2. Add CONFIG_FASTBOOT dependency, as fastboot buffer is
re-used in partition verification operations.
Reported-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Currently we can choose between 2 different types of behavior for the
serverip variable:
1) Always overwrite it with the DHCP server IP address (default)
2) Ignore what the DHCP server says (CONFIG_BOOTP_SERVERIP)
This patch adds a 3rd option:
3) Use serverip from DHCP if no serverip is given
(CONFIG_BOOTP_PREFER_SERVERIP)
With this new option, we can have the default case that a boot file gets
loaded from the DHCP provided TFTP server work while allowing users to
specify their own serverip variable to explicitly use a different tftp
server.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new command 'wol': Wait for an incoming Wake-on-LAN packet or
time out if no WoL packed is received.
If the WoL packet contains a password, it is saved in the environment
variable 'wolpassword' using the etherwake format (dot or colon
separated decimals).
Intended use case: a networked device should boot an alternate image.
It's attached to a network on a client site, modifying the DHCP server
configuration or setup of a tftp server is not allowed.
After power on the device waits a few seconds for a WoL packet. If a
packet is received, the device boots the alternate image. Otherwise
it boots the default image.
This method is a simple way to interact with a system via network even
if only the MAC address is known. Tools to send WoL packets are
available on all common platforms.
Some Ethernet drivers seem to pad the incoming packet. The additional
padding bytes might be recognized as Wake-on-LAN password bytes.
By default enabled in pengwyn_defconfig.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable a "avb" command to execute Android Verified
Boot 2.0 operations. It includes such subcommands:
avb init - initialize avb2 subsystem
avb read_rb - read rollback index
avb write_rb - write rollback index
avb is_unlocked - check device lock state
avb get_uuid - read and print uuid of a partition
avb read_part - read data from partition
avb read_part_hex - read data from partition and output to stdout
avb write_part - write data to partition
avb verify - run full verification chain
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
This patch adds support to load secure bitstreams(authenticated or
encrypted or both). As of now, this feature is added and tested only
for xilinx bitstreams and the secure bitstream was generated using
xilinx bootgen tool, but the command is defined in more generic way.
Command example to load authenticated and device key
encrypted bitstream is as follows
"fpga loads 0 100000 2000000 0 1"
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Introduce CONFIG_IMAGE_SPARSE and CONFIG_CMD_MMC_SWRITE so the "mmc
swrite" command is separated from the fastboot code.
Move image-sparse from common to lib so it's clear it's library code.
Rename CONFIG_FASTBOOT_FLASH_FILLBUF_SIZE to CONFIG_IMAGE_SPARSE_FILLBUF_SIZE
and migrate it to Kconfig.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have almost all pieces needed to support RISC-V UEFI binaries in place already.
The only missing piece are ELF relocations for runtime code and
data.
This patch adds respective support in the linker script and the runtime
relocation code. It also allows users to enable the EFI_LOADER configuration
switch on RISC-V platforms.
Signed-off-by: Alexander Graf <agraf@suse.de>
Because both major revisions are not compatible at all, let's make them
mutually exclusive in Kconfig. This way we will be sure, when using a
command or a library function that it is supported by the right
revision.
Current drivers are currently prefixed by "tpm_", we will prefix TPMv2.x
files by "tpm2_" to make the distinction without moving everything.
The Kconfig menu about TPM drivers is now divided into two sections, one
for each specification. Compliant drivers with one specification will
only show up if this specification _only_ has been selected, otherwise a
comment is displayed.
Once a driver is selected by the user, it selects automatically a
boolean value, that is needed in order to activate the TPM commands.
Selecting the TPM commands will automatically select the right
command/library files.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework deps as TPM_V1 and TPM_V2 depend on TPM,
drop TPM_DRIVER_SELECTED]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a command to manipulate the bootcounter. This is useful if you can
run device recovery from inside U-Boot and need to reset the bootcounter
after executing that process as part of altbootcmd.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Add a Kconfig option for BOOTP_NTPSERVER to enable the DHCP/BOOTP option
to configure the sntp server address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds smc and hvc commands, that allow issuing Secure Monitor
Calls and Hypervisor Calls conforming to the ARM SMC Calling Convention.
Add Kconfig items to allow each command can be individually enabled.
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Cortex-R* processors are a mid-range CPUs for use in deeply-embedded,
real-time systems. It implements the ARMv7-R architecture, and includes
Thumb-2 technology for optimum code density and processing throughput.
Except for MPU(Memory Protection Unit) and few CP15 registers, most of the
features are compatible with v7 architecture. So,reuse the same armv7
folder and introduce a new config CPU_V7R in order to differentiate
from v7 based platforms.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
CONFIG_CMD_LOG without CONFIG_LOG leads to a build error:
‘gd_t {aka volatile struct global_data}’ has no member named
‘default_log_level’
So CMD_LOG should select LOG.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The BOOTP options used to be and should still be default for all boards
with CMD_NET enabled. One should not be forced to use DISTRO_DEFAULTS to
get them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Improve the documentation and correct the listed dependencies.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Commit 3b3ea2c56e ("Kconfig: cmd: Make networking command dependent on NET")
removed the help documentation from the README but didn't add it back to Kconfig.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
The options were pretty unhelpful, so improve them some.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Move DHCP to directly follow BOOTP so that Kconfig can show the
dependency as a hierarchy.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Options that controlled the tftp and bootp commands depended on their
commands, but lived in the net menu.
Move them so they are in a consistent location.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Previously, CMD_NET was an alias for 2 commands (bootp and tftpboot) and
they we not able to be disabled. Separate out those 2 commands and move
CMD_NET up to the menu level, which more accurately represents the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds a command that enables the calculation of bit operations
(AND, OR, XOR) on binary data from the command line. Memory locations as
well as the contents of environment variables are eligible as sources
and destination of the binary data used in the operations.
The possible applications are manifold: Setting specific bits in
registers using the regular read-OR-write pattern, masking out bits in
bit values, implementation of simple OTP encryption using the XOR
operation, etc.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
In January some commits were introduced to mitigate the U-Boot image
size issues we encountered on sunxi builds.
Now with the MMC environment removed we can bring them back, as we
practically don't have a size limit anymore.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Clean up the screaming mess of configuration options that DFU is.
It was impossible to configure DFU such that TFTP is enabled and
USB is not, this patch fixes that and assures that DFU TFTP and
DFU USB can be enabled separatelly and that the correct pieces
of code are compiled in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
config_fallback.h has some logic that checks a variety of options
and selects LIB_UUID if it hasn't already been selected. This
will all LIB_UUID in Kconfig and select this option for the list
of options to allow us to remove the logic from fallbacks
Signed-off-by: Adam Ford <aford173@gmail.com>
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The CONFIG_USB_FUNCTION_MASS_STORAGE must be selected when one enables
support for ums command.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Migrate the following symbols to Kconfig:
CONFIG_FS_EXT4
CONFIG_EXT4_WRITE
The definitions in config_fallbacks.h can now be expressed in Kconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
