After power-on, both LAPIC and I/O APIC appear with the same APIC ID
zero, which creates an ID conflict. When generating MP table, U-Boot
reports zero as the LAPIC ID in the processor entry, and zero as the
I/O APIC ID in the I/O APIC as well as the I/O interrupt assignment
entries. Such MP table confuses Linux kernel and finally a kernel
panic is seen during boot:
BUG: unable to handle kernel paging request at ffff9000
IP: [<c101d462>] native_io_apic_write+0x22/0x30
*pdpt = 00000000014fb001 *pde = 00000000014ff067 *pte = 0000000000000000
Oops: 0002 [#1]
Modules linked in:
Pid: 1, comm: swapper Tainted: G W 3.8.7 #3 intel galileo/galileo
EIP: 0060:[<c101d462>] EFLAGS: 00010086 CPU: 0
EIP is at native_io_apic_write+0x22/0x30
...
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of asking each platform to provide reserve_arch(),
supply it in arch/x86/cpu/cpu.c in a unified way.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are still two places in Quark's MRC codes that use the generic
legacy PCI APIs, but as we are phasing out these legacy APIs, switch
to use Quark's own PCI config routines.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add a driver for interrupts on quark and move the code currently in
cpu_irq_init() into its probe() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present interrupt routing is set up from arch_misc_init(). We can do it
a little later instead, in interrupt_init().
This removes the manual pirq_init() call. Where the platform does not have
an interrupt router defined in its device tree, no error is generated. Some
platforms do not have this.
Drop pirq_init() since it is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With driver model timer conversion, quark based board does not boot
any more as mdelay() is called during quark_pcie_early_init() which
is before driver model gets initialized. Fix this breakage.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present pci_mmc_init() does not correctly use the PCI function since the
list it passes is not terminated. The array size passed to pci_mmc_init() is
actually not used correctly. Fix this and adjust the pci_mmc_init() to scan
all available MMC devices.
Adjust this code to use the new driver model PCI API.
This should move over to the new MMC uclass at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have converted all x86 boards to use driver model timer,
remove these legacy timer codes in the tsc driver.
Note this also removes the TSC_CALIBRATION_BYPASS Kconfig option,
as it is not needed with driver model.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Using existing mrccache library to implement mrc cache support
for Intel Quark.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC does not support MSR MTRRs. Fixed and variable range MTRRs
are accessed indirectly via the message port and not the traditional
MSR mechanism. Only UC, WT and WB cache types are supported.
We configure all the fixed range MTRRs with common values (VGA RAM
as UC, others as WB) and 3 variable range MTRRs for ROM/eSRAM/RAM as
WB, which significantly improves the boot time performance.
With this commit, it takes only 2 seconds for U-Boot to boot to shell
on Intel Galileo board. Previously it took about 6 seconds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Thermal sensor on Quark SoC needs to be properly initialized per
Quark firmware writer guide, otherwise when booting Linux kernel,
it triggers system shutdown because of wrong temperature in the
thermal sensor is detected by the kernel driver (see below):
[ 5.119819] thermal_sys: Critical temperature reached(206 C),shutting down
[ 5.128997] Failed to start orderly shutdown: forcing the issue
[ 5.135495] Emergency Sync complete
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
When Linux kernel boots, it hangs at:
[ 0.829408] Intel Quark side-band driver registered
This happens when Quark kernel Isolated Memory Region (IMR) driver
tries to lock an IMR register to protect kernel's text and rodata
sections. However in order to have IMR function correctly, HMBOUND
register must be locked otherwise the system just hangs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change existing codes to use clrbits, setbits, clrsetbits macros.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert to use DM version of Designware ethernet driver on Intel
quark/galileo.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB PHY needs to be properly initialized per Quark firmware writer
guide, otherwise the EHCI controller on Quark SoC won't work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC holds the PCIe controller in reset following a power on.
U-Boot needs to release the PCIe controller from reset. The PCIe
controller (D23:F0/F1) will not be visible in PCI configuration
space and any access to its PCI configuration registers will cause
system hang while it is held in reset.
Enable PCIe controller per Quark firmware writer guide.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
If we convert to use driver model pci on quark, we will encounter
some chicken and egg problems like below:
- To enable PCIe root ports, we need program some registers on the
message bus via pci bus. With driver model, the first time to
access pci bus, the pci enumeration process will be triggered.
But without first enabling PCIe root ports, pci enumeration
just hangs when scanning PCIe root ports.
- Similar situation happens when trying to access GPIO from the
PCIe enabling codes, as GPIO requires its block base address
to be assigned via a pci configuration register in the bridge.
To avoid such dilemma, replace all pci calls in the quark codes
to use the local version which does not go through driver model.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has a low end x86 processor with only 400MHz
frequency. Currently it takes about 15 seconds for U-Boot to
boot to shell and the most time consuming part is with MRC,
which is about 12 seconds. MRC programs lots of registers on
the SoC internal message bus indirectly accessed via pci bus.
To speed up the boot, create an optimized version of pci config
read/write dword routines which directly operate on PCI I/O ports.
These two routines are inlined to provide better performance too.
Now it only takes about 3 seconds to finish MRC, which is really
fast (4 times faster than before).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This function can fail. In this case we should return the error rather than
swallowing it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
By default the legacy segments (A0000h-B0000h, E0000h-F0000h)
do not decode to system RAM. Turn on the decode so that we can
write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
These functions currently use a generic name, but they are for x86 only.
This may introduce confusion and prevents U-Boot from using these names
more widely.
In fact it should be possible to remove these at some point and use
generic functions, but for now, rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel Quark SoC integrates two 10/100 ethernet controllers which can
be connected to an external RMII PHY. The MAC IP is from Designware.
Enable this support with the existing U-Boot Designware MAC driver
so that the ethernet port on Intel Galileo board can be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Using __DATE__ and __TIME__ results in an error due to -Werror=date-time
with gcc-4.9 (__DATE__ / __TIME__ might prevent reproducible builds) so
switch these over to U_BOOT_DATE / U_BOOT_TIME
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the quark MRC codes coding style by:
- Remove BIT0/1../31 defines from mrc_util.h
- Create names for the documented BITs and use them
- For undocumented single BITs, use (1 << n) directly
- For undocumented ORed BITs, use the hex number directly
- Remove redundancy parenthesis all over the codes
- Replace to use lower case hex numbers
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Intel Galileo board has a microSD slot which is routed from Quark SoC
SDIO controller. Enable SD/MMC support so that we can use an SD card.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Quark SoC contains a legacy SPI controller in the legacy bridge
which is ICH7 compatible. Like Tunnel Creek and BayTrail, the BIOS
control register offset in the ICH SPI driver is wrong for the Quark
SoC too, unprotect_spi_flash() is added to enable the flash write.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC has some non-standard BARs (excluding PCI standard BARs)
which need be initialized with suggested values. This includes GPIO,
WDT, RCBA, PCIe ECAM and some ACPI register block base addresses.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have added Quark MRC codes, call MRC in dram_init() so
that DRAM can be initialized on a Quark based board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
For some unknown reason, the TSC calibration via PIT does not work on
Quark. Enable bypassing TSC calibration and override TSC_FREQ_IN_MHZ
to 400 per Quark datasheet in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add minimum codes to support Intel Quark SoC. DRAM initialization
is not ready yet so a hardcoded gd->ram_size is assigned.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC contains an embedded 512KiB SRAM (eSRAM) that is
initialized by hardware. eSRAM is the ideal place to be used
for Cache-As-RAM (CAR) before system memory is available.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In the Quark SoC, some chipset commands are accomplished by utilizing
the internal message network within the host bridge (D0:F0). Accesses
to this network are accomplished by populating the message control
register (MCR), Message Control Register eXtension (MCRX) and the
message data register (MDR).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
