Current implementation for getting chip ID uses either raw access on EL3
or a SMC call to get the silicon information. Following change
simplifies the code using always the firmware driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch merges ZynqMP firmware calls under xilinx_pm_request in order
to make trainsparent the EL. Calls at EL3 are send through IPI messages
and EL2 through SMC calls.
The EL2 call uses fixed payload and arg size as the EL3 call. The
firmware is capable to handle PMUFW_PAYLOAD_ARG_CNT bytes but the
firmware API is limited by the SMC call size.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes duplicated definition of PAYLOAD_ARG_CNT and define it in the
firmware driver. Additionally fixes payload buffer declarations without
macro usage
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DT binding is saying that default value is 0 not -1 that's why fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
s/xlnx,mio_bank/xlnx,mio-bank/g
DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Remove adhoc dt binding for fixed-partition definition for i2c eeprom.
fixed-partition are using reg property instead of offset/size pair.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable DFU tftp support for firmware update. Fill dfu_ram_tftp variable to
have command present for showing how to use it.
boot FIT image has been created from below fragment. Key part is that type
of image has to be firmware. Also based on experiment load property is
completely ignored and base addresses are taken from dfu_alt_info variable.
$ cat update_uboot.its
/dts-v1/;
/ {
description = "Automatic U-Boot update";
#address-cells = <1>;
images {
Image {
description = "Kernel";
data = /incbin/("/tftpboot/Image");
compression = "none";
arch = "arm64";
type = "firmware";
os = "linux";
load = <0x80000>;
entry = <0x80000>;
hash-1 {
algo = "sha1";
};
};
system.dtb {
description = "DTB";
data = /incbin/("/tftpboot/system.dtb");
compression = "none";
arch = "arm64";
type = "firmware";
load = <0>;
hash-1 {
algo = "sha1";
};
};
};
};
$ mkimage -f update_uboot.its /tftpboot/boot
When U-Boot starts get IP address and server IP.
dhcp
setenv serverip 192.168.0.105
And then run prepared command.
run dfu_ram_tftp
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Image should be loaded to 0x80000 address and not to $kernel_addr_r.
Also kernel_addr, fdt_addr and fdt_size in zynqmp case are not defined
that's why define it to be aligned with Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini U-boot runs on lower foot print of 256KB OCM. Hence 8K memory
for malloc may not be required. Reduce it by 1.5K.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Find and use the lowest memory for Versal to make sure that we keep u-boot
as low as possible and never use memory above u-boot's maximum VA mapping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert fdtdec_setup_mem_size_base(), get_next_memory_node(),
fdtdec_setup_memory_banksize() and fdtdec_setup_mem_size_base_lowest() to
livetree API.
Tested on ZynqMP zcu104 board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
New function should be called from board dram_init() because it initialized
gd->ram_base/ram_size. It finds the lowest available memory.
On systems with multiple memory nodes finding out the first memory node by
fdtdec_setup_mem_size_base() is not enough because this memory can be above
actual U-Boot VA mapping. Currently only mapping till 39bit is supported
(Full 44bit mapping was removed by commit 7985cdf74b ("arm64: Remove
non-full-va map code")).
If DT starts with the first memory node above 39bit address then system can
be unpredictable.
The function is available only when multiple memory bank support is
enabled.
Calling fdtdec_setup_memory_banksize() from dram_init() is not possible
because fdtdec_setup_memory_banksize() is saving dram information to bd
structure which is placed on stack but not initialized at this time. Also
stack is placed at location setup in dram_init().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PM return payload size is defined as 4 bytes for Versal arquitecture
while the PM calls implemented both in the Versal clock driver and
ZynqMP firmware driver expects 5 bytes length.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Versal loadpdi command is used for loading secure & non-secure
pdi images.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Origin function was calling strsep which replaced delimiter ',' by a null
byte ('\0'). Operation was done directly on FDT which ends up with the
following behavior:
ZynqMP> printenv fdtfile
fdtfile=xilinx/zynqmp.dtb
ZynqMP> fdt addr $fdtcontroladdr
ZynqMP> fdt print / compatible
compatible = "xlnx", "zynqmp"
As is visible fdtfile was correctly composed but a null byte caused that
xlnx was separated from zynqmp.
This hasn't been spotted because in all Xilinx DTs there are at least 3
compatible string and only the first one was affected by this issue.
But for systems which only had one compatible string "xlnx,zynqmp" it was
causing an issue when U-Boot's DT was used by Linux kernel.
The patch removes strsep calling and strchr is called instead which just
locate the first char after deliminator ',' (variable called "name").
And using this pointer in fdtfile composing.
Fixes: 91d7e0c47f ("arm64: zynqmp: Create fdtfile from compatible string")
Reported-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
On system with PL DDR which is placed before PS DDR in DT
env_get_bootm_size() and env_get_bootm_low() without specifying bootm_low
and bootm_size variables are taking by default gd->bd->bi_dram[0].start and
gd->bd->bi_dram[0].size. As you see 0 means bank 0 which doesn't need to be
PS ddr and even can be memory above 39bit VA which is what U-Boot supports
now.
That's why setup bootm variables based on ram_base/ram_size setting to make
sure that boot images are placed to the same location as U-Boot is placed.
This location should be by default location where OS can boot from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
asm_sel is for switching between sata and pcie mode
on r64 there is GPIO90 connected to ASM1480 which
switches RX/TX pairs to PCIe/SATA connector
output-low means sata-controller is active
with 2020-10 now reg is also needed for the phy itself
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
add support for PHY_TYPE_SATA to Mediateks TPHY driver
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
This patch adds PCIe node in dts for Mediatek MT7622 Soc.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
This patch adds PCIe support for the Mediatek MT7622 SOC.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
This patch adds pciesys support in dts for MediaTek MT7622 SoC.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
This patch adds pciesys support in clock driver for
MediaTek MT7622 SoC.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
- Remove pinmux definition from pico-imx6ul.c
- Enable NET_RANDOM_ETHADDR for temporary solution, because micrel_ksz8xxx
driver does not support DM_ETH yet, so cannot read MAC address directly.
Before enable DM_ETH:
Net: FEC [PRIME]
After enable DM_ETH:
Net:
Warning: using random MAC address - ca:3f:43:8f:67:d4
eth1: ethernet@20b4000
Here is the test commands:
=> dhcp
BOOTP broadcast 1
DHCP client bound to address 10.88.88.94 (139 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
=> ping 8.8.8.8
Using ethernet@20b4000 device
host 8.8.8.8 is alive
Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
It's due to the warning messages issue after compiled:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Enable DM_VIDEO can fix it on the stage of compilation.
Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The correct order is load address, offset, length. The order was
accidentally switched a while ago; make it match the HAB Blocks output and
what CST expects again.
Fixes: e97bdfa5da ("tools/imximage: share DCD information via Kconfig")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This function is unused since commit 862274913f ("bus:
uniphier-system-bus: move hardware init from board files").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fill is code for programming the DDR_PHY_CMD_DESKEW_CONx registers,
which are optional, but can be used to fill in the byte lane delays.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX7 by
reading out the SRC GPR10 bit 30. This bit is either set by the BootROM
if it switched to the secondary copy due to primary copy being corrupted
OR it can be overridden by the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add new 'getprisec' subcommand to 'bmode' command, which sets the return
value of the 'bmode' command to either 0 if the system booted from primary
copy or to 1 if the system booted from secondary copy. This can be used
e.g. in 'test' command to determine which copy of the system is running.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The i.MX6/i.MX7 is capable of booting a secondary "redundant" system
image in case the primary one is corrupted. The user can force this
boot mode as well by explicitly setting SRC GPR10 bit 30. This can be
potentially useful when upgrading the bootloader itself. Expose this
functionality to the user.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add the basic differentiation between i.MX6 and i.MX7 into the bmode
command, the mechanism really works almost the same on both platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This series includes bug fixes for:
* UEFI secure boot - images with multiple signatures
* UEFI secure boot - support for intermediate certificates
* corrections for UEFI unit tests
* missing loadaddr on MAIX board
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl82zyEACgkQxIHbvCwF
GsR8GQ/9FzCCfmhu2VhVI1cUKIT2B/FhAXbADAAhmBFk1SezhnKrsWUFFUbHeD+v
c0+QKBldIARxpD40M68FNP7QVA35iaU2+Z5jBQ7r5ZUuTuZkxeFavtHRXlSCL02R
rmdsKTtwPTRgve3IxEFJcxc4jpvAhNH+QLveK+PA+gUGjd2UoYWoGknJ4n8oe2rG
uDX4em8Sy1LXrkJLCf5Ae8+M3FBOtsBAFif1tX5cWnH5kP3DbL9A5A5JHxlVJEQi
SBC8NuJW+At89VlckEGpREt8itFMicdbLT/dSKDU3kh+l/h6zTbd9fGmoKLKXDdw
O/qwC2kwsKg/jrfZwYOTzUIpRt3jhe+CwrEajVJY12jIQzAW4kvj2mo9AeBEydHO
umFfbExGH8zwZgynrhhbjHdNxcGBahUGLoKLCkJI51I7EwCMCrN5rtUpUzxVybTE
VJKyTqlyUSIZGU4AsQT3KflLGRGU/HNS2ariQWjEbKWcCC03Q7dXH1RQMUxTlqL3
Owhqv/NI07WIvQZD3oWPkn3Z8tiQMzF370qO2gb/AwM7U0P3ggkcUxAs7mCIj5x6
81PP65di4+zRzCyU1IHCILem7LHxGR6drGatbHspGBYAJrPduyM2cYAa0eXUOCvX
Hz1GURhlVGwBdBAwaZ+g13/NtisrkRBQQYZO8jiEBqhnWoc3514=
=0ZD1
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc3 (2)
This series includes bug fixes for:
* UEFI secure boot - images with multiple signatures
* UEFI secure boot - support for intermediate certificates
* corrections for UEFI unit tests
* missing loadaddr on MAIX board
