This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
After MMC is converted to DM, convert to use DM SCSI as well for all
x86 boards and imply BLK for both MMC and SCSI drivers.
CONFIG_SCSI_DEV_LIST is no longer used. Clean them up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Occasionally it was observed that on Intel MinnowMax board, with a
USB 2.0 device connected to the bottom port, when doing 'usb start'
on the xHCI controller:
scanning bus 0 for devices... cannot reset port 3!?
But neither of the two USB ports is routed to xHCI root port 3.
Adding some debug information shows that xHCI port 3 PORTSC register
mysteriously reports both CCS = 1 and CSC = 1.
This is not seen every time. After increasing the timeout to wait
for power to become stable, the issue is gone. So this indicates
current default USB power-on delay (20ms) might be at a critical
region where power is stable/unstable. U-Boot provides a mechanism
to have a environment variable to override the default one. Add
one for MinnowMax.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
As all x86 boards have been switched over to use DM USB, remove
CONFIG_USB_MAX_CONTROLLER_COUNT which is not used by DM USB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
GPIO bank E pin 8 & 9 are used to control the on-board two USB ports
VBUS on/off. Let's configure them in the misc_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present only chromebook boards are converted to DM video. Other
x86 boards are still using the legacy cfb_console driver. This
switches to use DM version drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently U-Boot environment address is at offset 0x7fe00 of a 8MB
SPI flash. When creating a partial u-boot.rom image without flash
descriptor and ME firmware, U-Boot actually occupies the last 1MB
of the flash, and reprograming U-Boot causes previous environment
settings get lost which is not convenient during testing.
Adjust the environment address to 0x6ef000 instead (before the MRC
cache data region in the flash).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
A number of moveconfig.py runs have left a instances of multiple empty
lines in a row. Correct this to a single empty line.
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Some boards have an i8042 device. Enable the driver for all x86 boards, and
add a device tree node for those which may have this keyboard.
Also adjust the configuration so that i8042 is always separate from the VGA,
and rename the stdin driver accordingly. With this commit the keyboard will
not work, but it is fixed in the next commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_SYS_EARLY_PCI_INIT is not needed any more since with driver
model, PCI enumeration is automatically triggered.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It looks that x86 chipset always contains a host bridge at pci
b.d.f 0.0.0, so enable this for all boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Set up interrupts correctly so that Linux can use all devices. Use
savedefconfig to regenerate the defconfig file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The BayTrail SoC has 4 different PCI devices IDs regarding to IDE
and AHCI. Add these IDs in pci_ids.h and also add the other SATA
ID in the Bayley Bay and MinnowMax board configuration header.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
These are now in the device tree so we don't need to use the CONFIG options.
Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On Intel BayTrail SoC, there is a legacy UART (I/O 0x3f8) integrated
into the SoC which is enabled by the FSP. Remove the smsc47x superio
initialization codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that the RTL8169 driver warning is fixed we can drop this. The incorrect
value is causing problems with USB EHCI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable a SPI environment and store it in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some x86 boards set CONFIG_NR_DRAM_BANKS to 1, which causes incorrect
DRAM size printed when booting from coreboot, like this:
CPU: x86, vendor Intel, device 663h
DRAM: 636 KiB
Using default environment
Change it to 8 which should be enough for both coreboot and bare
cases, and move it to x86-common.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The SPI NOR on the minnowboard max is a MICRON N25Q064A
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since all x86 boards use spi flash as its bootloader storage media,
it makes sense to make CONFIG_ENV_IS_IN_SPI_FLASH a common option.
So far only minnowmax board does not support it so undefine it in
its board configuration file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a relatively low-cost x86 board in a small form factor. The main
peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800
series CPU. So far only the dual core 2GB variant is supported.
This uses the existing FSP support. Binary blobs are required to make this
board work. The microcode update is included as a patch (all 3000 lines of
it).
Change-Id: I0088c47fe87cf08ae635b343d32c332269062156
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
