At the moment the QEMU firmware command just prints the size of the
loaded binaries on the console.
To go with all the other load methods, and many boot scripts'
expectations, also store the size of the file loaded last in the
environment variable "filesize".
We first put the kernel size in there, but overwrite this with the
initrd size, should we have one, because this is probably the more
prominent user of $filesize (in the booti or bootz command).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add gpio driver for ADP5585 I/O Expander Controller. The ADP5585 is a 10
input/output port expander and can be used to increase the number of
I/Os available to a processor.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Aspeed BMCs are commonly used with NC-SI. A system indicates the driver
should configure the link over NC-SI using the device tree.
Add it to the defconfig so we get compile coverage of the driver, even
if the EVBs do not normally use it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Update the ftgmac100 driver to support NC-SI instead of an mdio phy
where available. This is a common setup for Aspeed AST2x00 platforms.
NC-SI mode is determined from the device-tree if either phy-mode sets it
or the use-ncsi property exists. If set then normal mdio setup is
skipped in favour of the NC-SI phy.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Adds an "ncsi" command to manually start NC-SI configuration.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Add the handling of NC-SI ethernet frames, and add a check at the start
of net_loop() to configure NC-SI before starting other network commands.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
- Enforce CONFIG_DM being enabled (which has been the case for all
boards for a bit now) and remove non-DM_KEYBOARD options as they're also
unused for some time now.
There are no platforms that have not migrated to using DM_KEYBOARD,
remove the legacy option.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are no longer any platforms which do not enable DM, move this to a
def_bool y and remove the check in the Makefile.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmNSPhMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDrHCACddHL6pElPVUvNWomJ
h7RNejIaFrm+V2tVoDqnUBEzxKod7g1cvBiZM+2o5fcLNIrWfH0gV+7a48Uybzt2
r7VZ9u5Rnl1Fhhjvr8eL3uF/39V249eMPrzR8xC677sCJJkcczoOw8n4y534FaJZ
1NePmMKhlo7YVEZKzwdg1sM6sUppXniSEXUllWumVaUgSHcZhFK579nCbYpt25bW
sJ1V3fY2pJnaFHv9H599zSK79Izf5fR4fr3egKZknw8oqNLKNrjkWxxlPXJfjEYr
ncFJ31dOZXJU09rRoE60nIc0QdRE8dvELjYhPKUS/wmFDg7IotwNj5GcX2RIlRPJ
mS22
=D3FL
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.01 cycle:
This small fixes set includes an indentation fix for sam9x60 DT and one
name for one pin for sama7g5.
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Fix the MMC env device for boards with eMMC by adding a
board_mmc_get_env_dev override to return the boot device as the
MMC env device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
With sf update fixed to support unaligned start offset, use plain
sf update to update the bootloader in SPI NOR. This also helps
avoid the case where not enough SPI NOR has been erased and the
bootloader has been written to unerased area, and thus corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The btrfs filesystem provides advanced functionality like copy-on-write
and snapshots, as well as metadata and data duplication and checksumming.
Enable btrfs in U-Boot to permit even the primary partition to be btrfs
and let system boot from it.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
issue:
CAAM fails with key error when perform Modular Exponentiation
using PKHA Block in CAAM
Fix:
add flush and invalidate dcache for keys, signature
and output decrypted data processed by CAAM.
Fixes: 34276478f7 (DM: crypto/fsl - Add Freescale rsa DM driver)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Update the distro config env memory layout for the Apalis iMX6,
Colibri iMX6, Colibri iMX6ULL and Colibri iMX7:
- loadaddr=0x84200000 (resp. 0x14200000 on them i.MX 6) allows for 64MB
area for uncompressing (ie FIT images)
- fdt_addr_r = loadaddr + 64MB : allows for 64MB kernel
- scriptaddr = fdt_addr_r + 512KB : allows for 512KB fdt
- pxefile_addr_r = scriptaddr + 512KB : allows for 512KB script
- ramdisk_addr_r = pxefile_addr_r + 512KB : allows for 1MB extlinux.conf
Memory layout analogous to 64-bit one from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout") but left pxefile_addr_r
updated according to doc/develop/distro.rst.
This fixes a potential issue caused by the compressed kernel being
relocated on top of the ramdisk causing its corruption.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
After commit 395110284b ("nitrogen6x: Populate FDTFILE at build-time
for all platforms") iMX.6Q Sabrelite fails to boot due to a bad fdtfile
string:
Retrieving file: /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb
** File not found /dtbs/5.18.0-0.deb11.4-armmp/"imx6q-sabrelite".dtb **
CONFIG_DEFAULT_DEVICE_TREE option is string typed, so __stringify() is
adding extra quotes. Remove this.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the
QSPI clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the
ecspi clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock
inside the non-SPL block to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
PWM is not used inside SPL, so do not define the PWM clocks inside
SPL to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Move init_clk_usdhc to non-clk driver case, since assigned-clocks properties
will initialize the clocks by clk driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
... to avoid loosing characters when pasting text into the serial console.
This allows to remove the workaround to disable the vidconsole output
when no HDMI device is detected. This workaround only was there to speed-up
serial console processing.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add Serial Download Protocol support as it is a useful method to
load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot
proper using the following 'uuu'command:
$ uuu -brun spl flash.bin
Based on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO
to reduce its size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add an entry for USB boot so that U-Boot could be loaded via
the Serial Download Protocol.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable DM USB, DM PHY and USB gadget support in imx8mm-mx8menlo SPL
to let the board continue SDP loading of second stage after the first
stage was loaded by BootROM SDP implementation. It is not possible to
jump back into BootROM v1 and let the BootROM implementation continue
the SDP loading, all this has to be performed by the U-Boot CI HDRC
controller driver and SDP protocol implementation, both of which fit
into the SPL just barely.
With this patch, it is possible to start both U-Boot SPL and U-Boot
using e.g. uuu on this board as follows:
$ uuu -brun spl flash.bin
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The current implementation of spl_board_init() USB boot handling is
not correct, the MX8MM BootROM v1 does not support SDP load when
re-entered from U-Boot SPL, it is up to U-Boot to perform the next
stage load using its own internal CI gadget driver and SDP protocol
implementation. Drop the spl_board_init() to let SPL continue with
normal load in case the SDP support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The current implementation of spl_board_init() is not correct,
the MX8MM BootROM v1 does not support SDP load when re-entered
from U-Boot SPL, it is up to U-Boot to perform the next stage
load using its own internal CI gadget driver and SDP protocol
implementation. Drop the spl_board_init() to let SPL continue
with normal load in case the SDP support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Instead of duplicating code implemented by i.MX8M version of arch_misc_init()
in every board, enable CONFIG_ARCH_MISC_INIT and call arch_misc_init() from
spl_board_init(). This removes the duplication. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The signal name of pin PB2 with function F is FLEXCOM11_IO1
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
The indentation went far on the right due to an extra tab for
each pinctrl sub-nodes.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
- dts update and sync for rk356x, rk3288, rk3399 from Linux;
- Add rk3399 EAIDK-610 board support;
- Update for puma-rk3399 board;
- some fix and typo fix in different drivers;
The first production revision of the MX8M Mini Menlo board implements
a hardware change which swaps console UART and another UART connector.
Implement the swap, which maps the console UART back to the way Verdin
console is mapped.
Signed-off-by: Marek Vasut <marex@denx.de>
The GW7903 revision B adds two additional GPIO's to control the
direction of the 2 isolated digital I/O circuits.
Define them as:
- dig1_ctl
- dig2_ctl
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the GW74xx PMIC configuration:
- increase VDD_SOC DVS1 to 0.85V per datasheet
- increase VDD_SOC DVS0 to 0.95V before first DRAM access
- increase VDD_ARM DVS0 to 0.95V to support kernel overdrive voltage (OD)
- remove unnecessary changes to VDD_DRAM as we don't use 3GHz DRAM
- remove unnecessary change to LDO2 as it is unused
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
v2: update commit log with more detail
Update the M2 socket gpio hogs such that they are not active on boot by
flagging them as GPIO_ACTIVE_HIGH so that 'output-high' drives high.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the UART config gpio hogs such that it is configured for RS232
by default on boot. Additionally rename them to match the names used
on the reset of the venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add RAM auto-sizing, without this change memory size for all SKU is set
to 8GB and the system will crash on SKU with less memory as soon as the
non existent memory addresses are accessed.
Fixes: 2bc2f817ce ("board: toradex: add verdin imx8m plus support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
With this call the following attributes get set to the device-tree
and are then accessible from linux in /proc/device-tree/
serial-number: The serial number that is stored in config-block
toradex,board-rev: The version of the module (e.g. V1.1A)
toradex,product-id: The SKU number of the module runnin
Fixes: commit 2bc2f817ce ("board: toradex: add verdin imx8m plus support")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
With this call the following attributes get set to the device-tree
and are then accessible from linux in /proc/device-tree/
serial-number: The serial number that is stored in config-block
toradex,board-rev: The version of the module (e.g. V1.1A)
toradex,product-id: The SKU number of the module running
Fixes: commit 14d5aeff77 ("board: toradex: Add Verdin iMX8M Mini support")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable the I2C bus and set a env variable for the reset GPIO of the touch
controller. This allows us to probe the panel in a script.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Refactor the code a bit without any functional changes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Improve the naming of the regulators to contain the voltage rail
names from the schematic.
Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adjusts the names of the boards and SoMs to the official naming
used by Kontron marketing. These changes also affect devicetree
names and compatibles. The same changes have been submitted to the
Linux kernel.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
