Some ubi commands returned negative error codes, resulting in
the following error message on the prompt:
"exit not allowed from main input shell."
Negative error codes are not allowed.
This patch now changes the UBI code to return positive error codes.
Additionally "better" error codes are used, for example "ENOMEM" when
no memory is available for the UBI volume creation any more.
Also the output of some commands is enhanced:
Before:
=> ubi read 100000 testvol 100000
Volume testvol found at volume id 0
read 1048576 bytes from volume 0 to 100000(buf address)
=> ubi write 100000 testvol 1000
Volume testvol found at volume id 0
After:
=> ubi read 100000 testvol 100000
Read 1048576 bytes from volume testvol to 00100000
=> ubi write 100000 testvol 1000
4096 bytes written to volume testvol
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The start.o section is changed by --gc-section option of ld.
Of this using KEEP order, therefore, evade this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Some board of SH does not have flash memoy.
This revises it to initialize Flash when CONFIG_SYS_NO_FLASH is not
defined.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There is a small ordering issue in the master core in that we need to
make sure the disabling of the timebase in the SoC is visible before we
set the value to 0. We can simply just read back the value to
synchronizatize the write, before we set TB to 0.
Reported-by: Dan Hettena
Tested-by: Dan Hettena
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The POST word is stored in a spare register in the PIC on MPC8[5/6]xx
processors. When interrupt_init() is called, this register gets reset
which resulted in all POST_RAM POSTs not being ran due to the corrupted
POST word. To resolve this, store off POST word before the PIC is
reset, and restore it after the PIC has been initialized.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Timeout counter value is set as DTOCV bits in SYSCTL register
For counter value set as timeout,
Timeout period = (2^(timeout + 13)) SD Clock cycles
- As per 4.6.2.2 section of SD Card specification v2.00, host should
cofigure timeout period value to minimum 0.25 sec.
- Number of SD Clock cycles for 0.25sec should be minimum
(SD Clock/sec * 0.25 sec) SD Clock cycles
= (mmc->tran_speed * 1/4) SD Clock cycles
- Calculating timeout based on
(2^(timeout + 13)) >= mmc->tran_speed * 1/4
Taking log2 both the sides and rounding up to next power of 2
=> timeout + 13 = log2(mmc->tran_speed/4) + 1
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, pixis_reset altbank does not work properly. This patch
uses the correct mask to boot into the alternate bank.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Copying directly from ECM/PQ3 is not correct for how CoreNet based
platforms handle boot page translation.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch revised clk_adjust and wrlvl_start timings for corenet_ds, based
on testing on Virtium VL33B5163F-K9S and Kingston KVR1333D3Q8R9S/4G.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For DDR3 controller, the clk_adjust and wrlvl_start are platform-dependent.
The best values should be picked up from the middle of all working
combinations. This patch updates the table with confirmed values tested on
Hynix dual-rank UDIMMs (HMT125U7BFR8C-H9) at 1300MT/s, 1200MT/s, 1000MT/s,
900MT/s, 800MT/s and Kingston quad-rank RDIMMs (KVR1333D3Q8R9S/4G) at 1300MT/s,
1200MT/s, 1000MT/s.
Signed-off-by: York Sun <yorksun@freescale.com>
The write recovery time of both registers should match. Since mode register
doesn't support cycles of 9,11,13,15, we should use next higher number for
both registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We had an extra '0x' in the output of the LAWAR header that would cause
output like:
LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d
intead of:
LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
get_sp() was incorrectly excluded if none of
CONFIG_SETUP_MEMORY_TAGS
CONFIG_CMDLINE_TAG
CONFIG_INITRD_TAG
CONFIG_SERIAL_TAG
CONFIG_REVISION_TAG
were defined.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.
This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.
This patch is tested with compilation for armada100 and guruplug.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Commit 3c0659b "ARM: Avoid compiler optimization for readb, writeb
and friends." introduced I/O accessors with memory barriers.
Unfortunately the new write*() accessors introduced a bug:
The problem is that the argument "v" gets evaluated twice. This
breaks code like used here (from "drivers/net/dnet.c"):
for (i = 0; i < wrsz; i++)
writel(*bufp++, &dnet->regs->TX_DATA_FIFO);
Use auxiliary variables to avoid such problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Alexander Holler <holler@ahsoftware.de>
Cc: Dirk Behme <dirk.behme@googlemail.com>
These variables are only used in case CONFIG_SYS_NO_FLASH is NOT set:
struct mtd_device *dev;
struct part_info *part;
u8 dev_type, dev_num, pnum;
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Add waiting for receiving Ethernet gadget state on the Windows host
side before dropping pullup, but keep it for debug.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Port USB gadget RNDIS protocol support from linux-2.6.26
(.27 gadget stack actually has composite drivers).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Disconnecting USB gadget with pending interrupt may cause its wrong
handling in the next time when interface will be started again
(especially actual for RNDIS). This interrupt may force the gadget
to queue unexpected response before setup stage.
Despite the fact that such interrupt handled after dropped pullup
also may add pending response, this will not bring to any issues due to
usb_ep_disable (which clears the queue) called on gadget unregistering.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.
Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.
Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix the problem which cannot build the U-boot, if we only set
the CONFIG_ENV_IS_IN_SPI_FLASH.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The unzip command did not provide a way for the caller to get any
information about the uncompressed size. To make it better usable in
scripts, we now store the uncompressed size in the `filesize'
variable, like we do when for example loading a file over the network
or when reading it from a file system. Following that analogy, it is
only consequent to also print the size.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The implementation of the string compare function of the "itest"
command was weird, as only the length of the shortest argument was
included in the compare, with the result that something like
"itest.s abd == abddef" would return TRUE. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
u-boot BSP generates XILINX_USE_MSR_INSTR macro
even for system with MSR=0. That's why explicitly
check that MSR=1.
Signed-off-by: Michal Simek <monstr@monstr.eu>
