To allow bigger 64 bit prefetchable PCI regions in Linux, this patch
changes the base address and range of the ACPI area passed to Linux.
BayTrail can only physically access 36 bit of PCI address space. So
just chaning the range without changing the base address won't work
here, as 0xf.ffff.ffff is already the maximum address.
With this patch, a maximum of 16 GiB of local DDR is supported. This
should be enough for all BayTrail boards though.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce a new script to check whether file exists and
use that check in Makefile to avoid break CI system.
The script return 1 when the required files not exists, return 0
when files exists. The script will ignore check to u-boot-dtb.bin,
because if there is something wrong to generate u-boot-dtb.bin,
there must be some code error.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add compatible property and enable the FEC ipg clock when probing
on i.MX8X. Add specific function for reading FEC clock rate via
clock driver when configuring MII speed register. Allow FEC_MXC
selection for i.MX8.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The default Linux PHY reset delay is 10ms. This is also the requirement
for Marvell 88E151x PHYs, which are likely to be used with this Ethernet
MAC.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The dm_gpio_set_value() call sets the logical level of the GPIO signal.
That is, it takes the GPIO_ACTIVE_{LOW,HIGH} property into account. The
driver needs to assert the reset, and then deassert it. Not the other
way around.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT property "phy-mode" already provides the transceiver type.
Use it so that we do not have to also set CONFIG_FEC_XCV_TYPE
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Configure the phy regulator if defined by the "phy-supply" DT phandle.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DT binding says:
- phy-reset-duration : Reset duration in milliseconds. Should present
only if property "phy-reset-gpios" is available. Missing the property
will have the duration be 1 millisecond. Numbers greater than 1000 are
invalid and 1 millisecond will be used instead.
However the current code:
- clamps values greater than 1000ms to 1000ms rather than 1.
- does not initialize the delay if the property does not exist
(else clause mismatch)
- returns an error if phy-reset-gpios is not defined
Fix all this and simplify by using dev_read_u32_default()
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DT binding says that phy-reset-duration is in ms, but the driver
currently uses udelay().
Switch to mdelay() to fix this.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy reports a valid firmware version and doesn't indicate
a fault, skip loading the firmware. This allows the same image
to be used on boards that have firmware storage and those that do not.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In upcoming freescale board LX2160AQDS, the MDIO bus is muxed.
i.e. same MDIO bus can be routed to eight different slots depending
on mux register settings.
To support this mdio mux behavior, we add each MDIO bus mux as a
separate MDIO bus.
Now, various phy devices can be attached to each of these slots(mux).
The information about these devices is passed to OS via device tree.
To do the fdt fixups related to MDIO bus, its necessary that MDIO bus
list is accessed.Therefore, add a function to retrieve the list head.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
All mii operations require a valid PHY address except the 'device'
command, which expects the PHY name rather than the address.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add an entry for the warp7_bl33_defconfig target.
This fixes the following warnings:
WARNING: no status info for 'warp7_bl33'
WARNING: no maintainers for 'warp7_bl33'
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
- Split the AArch64 LS10xx and LS20xx builds into their own jobs, and
then exclude only ls1/ls2 from the catch-all. This moves the S32V234
job (and future i.MX8*) to the catch-all.
- Split spear out from arm926ejs and exclude freescale, not mx from that
job. The older Freescale i.MX boards are caught by the catch-all job
for Freescale but now we build the non-Freescale older i.MX platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
Odroid HC2 board is based on Odroid XU4 board, like the Odroid HC1.
The linux kernel does not provide a hc2 DTB so the hc1 DTB is also used
for the Odroid HC2.
Resend because MUA changed whitespace.
Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Unfortunately the test was not included in the original implementation.
Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Remove "environment" partition and do not read it when booting Android
from eMMC. We don't use this partition anymore, so this is just an
unintentional leftover.
Earlier we were reading dtb file from "environment" partition to feed it
further to kernel. Now we are using dtb from FIT image ("boot" partition
contains boot_fit.img image), which can be seen from this command:
bootm ${loadaddr}#${fdtfile}
where "#" character means we have FIT image in ${loadaddr} RAM address.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Praneeth Bajjuri <praneeth@ti.com>
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR
flash part connected to CS2 in addition to the NAND part on CS0.
This patch setups the GPMC timings for the MT28 NOR Flash and
enables the CFI-Flash driver now that the CFI stuff is in Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.
Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Compiling the overlay unit test fails with odroid-c2_defconfig showing
errors like:
test/overlay/cmd_ut_overlay.c:29:8:
error: unknown type name ‘fdt32_t’
Add the missing include.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently in pmecc_get_sigma(), the code tries to clear the memory
pointed by smu with wrong size 'sizeof(int16_t) * ARRAY_SIZE(smu)'.
Since smu is actually a pointer, not an array, so ARRAY_SIZE(smu)
does not generate correct size to be cleared.
In fact, GCC 8.1.0 reports a warning against it:
error: division 'sizeof (int16_t * {aka short int *}) / sizeof (int16_t
{aka short int})' does not compute the number of array elements
[-Werror=sizeof-pointer-div]
Fix it by using the correct size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
When booting and CPU is detected from cpuid, we also need an environment
variable that will be used in boot commands to load the proper devicetree.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
In my haste to migrate SPL to DM, I copied the wrong name.
While it really doesn't matter, I'd prefer the name to match
the board, so am335x_mmc0 is now called omap3_logic_mmc0
Signed-off-by: Adam Ford <aford173@gmail.com>
With the new omap_serial driver, this patch uses this instead
from the former ns16550_serial driver. Even though the
omap_serial driver is essentially the same.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the DM_USB working for USB host features, encapsulate the
USB gadget initialization in a precomiler check. If DM is enabled,
we don't need to manually initialize the MUSB driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
The default timings are assumming an OMAP36 / AM37 / DM37, but
the OMAP35 controller is a bit slower, so DDR may operate out of
spec when under stress. This patch checks the processor type and
sets the DDR timings according to processor type.
Fixes: 5ad4212ce0 ("ARM: DTS: Add Logic PD OMAP35/DM37 SOM-LV
and OMAP35 Torpedo")
Signed-off-by: Adam Ford <aford173@gmail.com>
The da850evm does not need this enabled, so this removes a
notice that appears during compile time that says
"Please remove"
Signed-off-by: Adam Ford <aford173@gmail.com>
Add default configuration to run u-boot as BL33 in the ARM Trusted Firmware
boot flow for AArch32 case.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: u-boot@lists.denx.de
If we have defined the OPTEE ram size and not OPTEE means that we are in
the case where OPTEE is loaded already (maybe by ARM Trusted Firmware) and
that most of the low level initialization is already done and that we
may/should skip it doing them here.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: u-boot@lists.denx.de
We may have, the not yet considered, scenario where OPTEE is loaded before
u-boot and *not* by u-boot, e.g, the boot flow using the ARM Trusted
Firmware (ATF), where in the 32bit flow is:
BootRom->ATF(BL2)->Optee(BL32)->u-boot(BL33)
In this case we need still to reserve the memory used by optee, to avoid
for example to realocate ourself to the same address at the end of DRAM.
So, we change here the dependencies on the OPTEE lib and we set the default
size and base of TZRAM to zero.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: u-boot@lists.denx.de
We can have the case where u-boot is launched after some other low level
enabler, like for example when u-boot runs after arm-trusted-firmware
and/or optee. So, because of that we may need to jump the initialization of
some IP blocks even because we may no longer have the permission for that.
So, if the config option to skip low level init is set disable also timer,
board and csu initialization.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: u-boot@lists.denx.de
Reviewed-by: Peng Fan <peng.fan@nxp.com>
