Currently the following devices are using a different definition for ROM
Vector Table addresses:
- i.MX6DQP = All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2
There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.
More details about RVT base address can be found on processors Reference
Manual and in the following documents:
EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison
EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Write, Check and Set MID commands have been deprecated from the Code
Signing Tool (CST) v2.3.3 and will not be implemented in newer versions
of HAB, hence the following features are no longer available:
- Write Data
- Clear Mask
- Set Mask
- Check All Clear
- Check All Set
- Check Any Clear
- Check Any Set
- Set MID
The inappropriate use of Write Data command may lead to an incorrect
authentication boot flow. Since no specific application has been identified
that requires the use of any of these features, it is highly recommended to
add this check.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For proper authentication the HAB code must check if the CSF is valid.
Users must call the csf_is_valid() function to parse the CSF prior to
authenticating any additional images. The function will return a failure
if any of the following invalid conditions are met:
- CSF pointer is NULL
- CSF Header does not exist
- CSF does not lie within the image bounds
- CSF command length zero
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. DCD should not be present in images that will be verified
by software using HAB RVT authentication APIs. Newer versions of HAB
will generate an error if a DCD pointer is present in an image being
authenticated by calling the HAB RVT API. Older versions of HAB will
process and run DCD if it is present, and this could lead to an incorrect
authentication boot flow.
It is highly recommended this check is in place to ensure additional HAB
verified images do not include a DCD table.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently it is not possible to run CMD_DEK on i.MX SPL targets:
=> dek_blob 0x12000000 0x12001000 128
The system hangs after running dek_blob because the CAAM clock is being
disabled by the HAB code. There is no need to disable CAAM clock after
authenticating additional boot images, thus keep CAAM clock enabled to
address this issue.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This reverts commit edf0093732 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.
These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
With fastboot support enabled, it is useful to be able to list
the eMMC EFI partitions, so select the CONFIG_EFI_PARTITION option.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Get rid of the SH I2C driver on Porter and enable the IIC driver
instead . The old SH I2C is completely broken on Porter anyway
and the DM/DT capable IIC driver allows access to the PMIC too.
Use the DM/DT capable driver instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable I2C6 bus on Porter to access the PMIC , ie. to reset the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The IIC on Gen2 is compatible with this driver as well, allow it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Set those limits to inform U-Boot about FDT and initramfs placement.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable cache and time commands, which are convenience tools for
doing benchmarks and various boot tests. Also enable FIT support
for booting fitImage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
late in the cycle, so this is something to be done in 2018.05.
Fix ommission where the u-boot,dm-pre-reloc DT bit was pulled into the
common DT, not the U-Boot specific DT part. Move it to U-Boot DT part.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With multiple environments, the 'get_char' callback for env
drivers does not really make sense any more because it is
only supported by two drivers (eeprom and nvram).
To restore single character loading for these drivers,
override 'env_get_char_spec'.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit 7d714a24d7 ("env: Support multiple environments") added
static variable env_load_location. When saving environmental
variables, this variable is presumed to have the value set before.
In case the value was set before relocation and U-Boot runs from a
NOR flash, this variable wasn't writable. This causes failure when
saving the environment. To save this location, global data must be
used instead.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Those two nodes are needed to configure pinmux before relocation
and to configure clock before relocation, since CPG/MSSR needs
access to RST node. This is not noticable on Gen3, but on Gen2
this causes problems in SPL if they are not available early.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Make the SCIF available before relocation and in SPL on R8A7791 Porter.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable support for applying DT overlays on Gen3. This is convenient
for handling extra additional hardware, like ie. the Kingfisher.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The SD driver calls clk_set_rate() before clk_enable(), yet clk_set_rate()
implementation in the clock driver does not set the SD-IF divider. Fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Commit 958d55f26c ("MAINTAINERS: Take over BCM2835 maintainership") put
me in as maintainer for the RPi soc, but forgot to update the board
MAINTAINERS file.
Add me there too.
Signed-off-by: Alexander Graf <agraf@suse.de>
Kconfig should only 'select' features that are required for an arch.
Standard features that can be disabled without breaking board support
should use 'imply' instead, to allow users to disable it.
These options are changed for mach-socfpga:
- DM_SPI & DM_SPI_FLASH: only required with QSPI support enabled
- SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION: the boot rom supports a
partitionless mode also, where SPL is located at address 0
- HW_WATCHDOG: while all mainline board defconfigs use it, U-Boot
should still work without it.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
All Socfpga boards from ./include/configs/socfpga_* define
CONFIG_HW_WATCHDOG.
To ease CONFIG_HW_WATCHDOG conversion to Kconfig select it in
config ARCH_SOCFPGA (arch/arm/Kconfig) section.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
This patch adds "spi-flash" to the compatible list of the qspi flash
chip for all socfpga boards. This is required to make qspi work on
these boards on top of the recent fixes. Without the "spi-flash"
compatible string for the flash chip, the speed cannot be read and a
speed of 0Hz is used (which results in a divide-by-zero on these
boards).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
ARC Elf32 tools by default enable usage of so-called "small data"
section or in ARC PRM parlance "GP-relative addressing".
The idea is to put up to 2kB of frequently used data into a separate
location and use indirect addressing via dedicated core register (GP).
Where GP is used as a base for offset calculation.
And so if "-msdata" toggle is passed to the compiler either explicitly
or implicitly (that's Elf32 tools case) it will try to put some data
in that "small data" area and then to calculate real offset from GP
to be encoded in instructions we need to know the base value which
liker gets from __SDATA_BEGIN__ symbol in hte linker script.
In U-Boot we don't use that feature and linker script doesn't define
__SDATA_BEGIN__ which gives us the following linkage error if we use
Elf32 tools:
------------------------->8-------------------
LD u-boot
.../bin/arc-elf32-ld.bfd: Error: Linker symbol __SDATA_BEGIN__ not found
.../bin/arc-elf32-ld.bfd: final link failed: Bad value
------------------------->8-------------------
Note if uClibc or glibc tools are used that problem doesn't happen
because usage of "small data section" is disabled by default as not very
useful for bigger executables. Moreover GP is just another name of r26
so we're loosing 1 core register which is not used by the compiler as a
generic register with "-msdata".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For some reason from day one we used to have both CONFIG_DWC2_UTMI_WIDTH
mentioned in dwc2.h and in scripts/config_whitelist.txt but never really used
and CONFIG_DWC2_UTMI_PHY_WIDTH used in real code in dwc2.c (but never
defined).
Moreover even though CONFIG_DWC2_UTMI_WIDTH might be either 8 or 16
depending on hardware (and the same is said in a comment for it in
dwc2.h) but then 8 is hardcoded in the header leaving no ability to
override this value in board's configuration.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_BOOTCOUNT_SINGLEWORD
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMIT
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
With commit 9bd76b8076 ("spl: make CONFIG_OF_EMBED pass dts through
fdtgrep"), CONFIG_SPL_MULTI_DTB_FIT has been broken because
cmd_fdtgrep was now unknown in scripts/Makefile.spl after moving
it to dts/Makefile. This bug has been introduced with v2018.01.
This patch moves cmd_fdtgrep from dts/Makefile to scripts/Makefile.lib
and includes scripts/Makefile.lib in scripts/Makefile.spl.
Fixes: 9bd76b8076 ("spl: make CONFIG_OF_EMBED pass dts through fdtgrep")
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
ATF recently began announcing PSCI v1.1. Since that version is unknown
to u-boot, the PSCI device nodes were not updated.
Switch from the case statement to a greater/less-than comparison so that
v1.1, as well as future versions, get at least the compatible nodes of
known versions.
PSCI v1.1 doesn't seem to have introduced a new corresponding compatible.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The single argument `--noheader' is expecting isn't taken from getopt
parsing, but instead from the remaining argv arguments.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
>From DFU_ALT_INFO_EMMC (include/environment/ti/dfu.h) we can see that
rootfs will be flashed to second partition on eMMC. But at the moment we
have only one partition in $partitions environment variable. Let's add
"bootloader" partition prior to "rootfs", so that DFU works correctly.
This also fixes eMMC boot, which looks for rootfs on second partition.
"bootloader" partition start corresponds to "u-boot.img.raw" in DFU
eMMC info, which is 0x300 sector (384 KiB offset from eMMC start).
rootfs start address can be also found from DFU eMMC info.
bootloader-related area is finished at 0x1500 sector (2688 KiB offset
from eMMC start). This should be the start address for rootfs in
$partitions environment variable.
While at it, fix U-Boot environment address to be the same as for
AM57x EVM, so that it doesn't clash with other partitions.
So now eMMC layout looks like this:
===============================================================
0 +------------------------+
| MBR/GPT header | 128 -
128 +------------------------+
| MLO | 256 -
384 +------------------------+
| u-boot.img | 1792 bootloader
2176 +------------------------+
| //////// hole //////// | 256 -
2432 +------------------------+
| U-Boot environment | 128 -
2560 +------------------------+
| U-Boot environment | 128 -
| (redundant) |
2688 +------------------------+
| rootfs | remaining rootfs
end +------------------------+
===============================================================
"hole" area can be used further for storing U-Boot environment (like
it's done in AM57x EVM config file) or for increasing u-boot.img area
(in case u-boot.img size increased, e.g. if new dtbs were added).
This commit conforms with Linux partition table from f6d245b8c5
("arm: am57xx: Fix Linux boot from eMMC") commit, making things in
uniform way.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.
Signed-off-by: Tom Rini <trini@konsulko.com>
