Add a generic function which can check whether a category has an
entry ID.
Signed-off-by: Naoki Hayama <naoki.hayama@lineo.co.jp>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_{SPL,TPL}_SIZE_LIMIT are defined as hex (SPL_SIZE_LIMIT was
converted in b51882d0 ("spl: Convert CONFIG_SPL_SIZE_LIMIT to hex"), but
there are still places that reference integer values. Change those to hex
as well. Also, update the Makefile to check for 0x0 instead of 0.
This also fixes the following build error when CONFIG_SPL_SIZE_LIMIT
is set by menuconfig to 0x0:
...
spl/u-boot-spl.bin exceeds file size limit:
limit: 0 bytes
actual: 0x80f0 bytes
excess: 0x80f0 bytes
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't want the debug output to be visible in a normal boot. Silence it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
It is much easier to read the bloblist addresses if it starts on a 4KB
boundary. Update it to align it accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be called when it is not known whether it will find
anything. This results in confusing log messages if the device is not
found. It is better for the caller to log the failure, if necessary.
Drop the logging from this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl+QXvgACgkQ4rK92eCq
k3Vbrgf/cBKPY9bS+lJVARgjDvIOdcXzpgH/F7dUlq+dzu/mCwhIBVKxM7/nXh5p
RhfGET2fpMYY/41LkKza7AqOiGTXZG4pTmCGe1UHXrXeIPjinWG1LQjU/KOk6U4n
681P9BZfTUXrVgzLBIUY1KBFVyMaiYfVjxU3MnA1vqrubymFbf+IpUt3OIegUDCp
AjrTdj7sFEQ3nG/pgTyqFCwkl/MG53aB9MiaBBRxeGHYnDn0qzAEHSGqzSZZGhNl
1ubJDF3K7w6Pj3MzIeA80M5r0fJoTy/qWcNH31psOpyQaHJ9NbPGjFYE6AkDPV4l
27QN71AcRtCzlv1XQpblA98pa1bUYw==
=Bl3G
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
Remove duplicated stdio print message.
It's already displayed in common/console.c.
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Odroid XU3/XU4/HC1/HC2 based on Exynos5422
Type: xu3
In: serial
Out: serial
Err: serial
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
A64-Teres-I board is a laptop which comes with a builtin keyboard.
The keyboard+trackpad controller pauses for 2 seconds at a firmware
prompt before loading its HID interface.
U-Boot needs to wait equally long to reliably enable the keyboard.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Series-Cc: Jagan Teki <jagan@amarulasolutions.com>
Series-Cc: Lukasz Majewski <lukma@denx.de>
Series-Cc: Andre Przywara <andre.przywara@arm.com>
Olimex OLinuXino LIME2 rev. H through L uses Micrel KSZ9031 PHY.
This enables the Micrel PHY for A20-OLinuXino-Lime2-eMMC_defconfig.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner sun50i SoCs contain an OpenRISC 1000 CPU that functions as a
System Control Processor, or SCP. ARM Trusted Firmware (ATF)
communicates with the SCP over SCPI to implement the PSCI system
suspend, shutdown and reset functionality. Currently, SCP firmware is
optional; the system will boot and run without it, but system suspend
will be unavailable.
Since all communication with the SCP is mediated by ATF, the only thing
U-Boot needs to do is load the firmware into SRAM. The SCP firmware
occupies the last 16KiB of SRAM A2, immediately following ATF.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add an entry type for a firmware blob for a System Control Processor,
given by an entry arg. This firmware is a raw binary blob.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since commit d879616e9e ("spl: fit: simplify logic for FDT loading for
non-OS boots"), the SPL looks at the "os" properties of FIT images to
determine where to append the FDT.
The "os" property of the "firmware" image also determines how to execute
the next stage of the boot process, as in 1d3790905d ("spl: atf:
introduce spl_invoke_atf and make bl31_entry private"). For this reason,
the next stage must be specified in "firmware", not in "loadables".
To support this additional functionality, and to properly model the boot
process, where ATF runs before U-Boot, add the "os" properties and swap
the firmware/loadable images in the FIT image.
Since this description was copied as an example in commit 70248d6a2916
("binman: Support generating FITs with multiple dtbs"), update those
examples as well for correctness and consistency.
Acked-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some boards, specifically 64-bit Allwinner boards (sun50i), are
extremely limited on SPL size. One strategy that was used to make space
was to remove the FIT "os" property parsing code, because it uses a
rather large lookup table.
However, this forces the legacy FIT parsing code path, which requires
the "firmware" entry in the FIT to reference the U-Boot binary, even if
U-Boot is not the next binary in the boot sequence (for example, on
sun50i boards, ATF is run first).
This prevents the same FIT image from being used with a SPL with
CONFIG_SPL_FIT_IMAGE_TINY=n and CONFIG_SPL_ATF=y, because the boot
method selection code looks at `spl_image.os`, which is only set from
the "firmware" entry's "os" property.
To be able to use CONFIG_SPL_ATF=y, the "firmware" entry in the FIT
must be ATF, and U-Boot must be a loadable. For this to work, we need to
parse the "os" property just enough to tell U-Boot from other images, so
we can find it in the loadables list to append the FDT, and so we don't
try to append the FDT to ATF (which could clobber adjacent firmware).
So add the minimal code necessary to distinguish U-Boot/non-U-Boot
loadables with CONFIG_SPL_FIT_IMAGE_TINY=y. This adds about 300 bytes,
much less than the 7400 bytes added by CONFIG_SPL_FIT_IMAGE_TINY=n.
Acked-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This consolidates the SoC-specific part at the top of the file to avoid
cluttering it up with preprocessor conditions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Prior to commit 7f7f8aca8257 ("sunxi: Convert 64-bit boards to use
binman"), if the BL31 environment variable was not defined, the firmware
would be loaded from a file "bl31.bin" in the current directory. Restore
that behavior by providing that as the default filename in case no entry
arg is provided, which will be the case if the environment variable is
unset.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Nodes should have a blank line separating them from sibling nodes and
properties. Add the necessary lines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Due to an extra level of indentation, the "data" property containing the
FDT was being written repeatedly after every other property in the node.
This caused the generated FIT image to be invalid.
Move the block up one level, so the property is added exactly once.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If neither CONFIG_SPL_FIT_SOURCE nor CONFIG_USE_SPL_FIT_GENERATOR is
enabled, U_BOOT_ITS will be undefined, and attempting to make u-boot.itb
will pass invalid arguments to mkimage, causing it to print its help
message.
Remove the rule in that case, so it is more obvious that u-boot.itb is
not something that can be made. This will reduce confusion as platforms
move away from CONFIG_USE_SPL_FIT_GENERATOR, as u-boot.itb was
previously a valid goal for those platforms.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Previously, because we have no source code about the DRAM initialization
of V3s and missing some configurations (delays and MBUS QoS info), our
V3s DRAM initialization sequence is hacked from the H3 one.
As the SDK shipped with PineCube contains source code for V3s libdram,
we can retrieve these information from it and tweak some other magic
bits.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
A use after free in the UEFI network stack is fixed.
-----BEGIN PGP SIGNATURE-----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=YCCZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc1 (2)
A use after free in the UEFI network stack is fixed.
This reverts commit eb39d8ba5f.
The commit breaks booting of fitImage by SPL, the system simply hangs.
This is because on arm32, the fitImage and all of its content can be
aligned to 4 bytes and U-Boot expects just that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Reuben Dowle <reuben.dowle@4rf.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The current default of 0x400 for SYS_MALLOC_F_LEN is too small if any
additional drivers marked as DM_FLAG_PRE_RELOC are loaded before
relocation.
CONFIG_RSA=y which is needed for UEFI secure boot or for FIT image
verification loads the driver mod_exp_sw which has DM_FLAG_PRE_RELOC.
CONFIG_LOG=Y is another setting requiring additional early malloc
area, cf. log_init().
When running pine64-lts_defconfig with CONFIG_RSA=y and debug UART enabled
we see as output in main U-Boot
alloc_simple() alloc space exhausted
With this patch the default values of SYS_MALLOC_F_LEN and
SPL_SYS_MALLOC_F_LEN on ARCH_SUNXI are raised to 0x2000.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update email address of Maxime Ripard in git-mailrc to match more
recently updated entry in MAINTAINERS.
commit 9bd9b2bcbe ("MAINTAINERS: Update my email address")
commit bf8f4c4400 ("MAINTAINERS: Update email address for Maxime Ripard")
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to the devicetree and the schematic, the 3.3V power rail for
the PHY is enabled by GPIO PC16. It's wired as active-high, with a
pull-up resistor, so actually works already when the GPIO is in
High-Z state.
However we should not take any chances and explicitly set the GPIO pin
to high, to avoid accidentally losing the PHY power.
The existing MACPWR Kconfig allows to do this easily.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When sending a command via the MDIO bus, the Designware MAC expects some
bits in the CMD register to describe the clock divider value between
the main clock and the MDIO clock.
So far we were omitting these bits, resulting in setting "00", which
means "/ 16", so ending up with an MDIO frequency of either 18.75 or
12.5 MHz.
All the internal PHYs in the H3/H5/H6 SoCs as well as the Gbit Realtek
PHYs seem to be fine with that - although it looks like to be severly
overclocked (the MDIO spec limits the frequency to 2.5 MHz).
However the external 100Mbit PHY on the Pine64 (non-plus) board is
not happy with that, Ethernet was actually never working there, as the
PHY didn't probe.
As we set the EMAC clock (via AHB2) to 300 MHz in ATF (on the 64-bit
SoCs), and use 200 MHz on the H3, we need the highest divider of 128
to let the MDIO clock end up below the required 2.5 MHz.
This enables Ethernet on the Pine64(non-plus).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation of sun8i_get_ephy_nodes() makes quite some
assumptions, in general relying on DT path names is a bad idea.
I think the idea of the code was to determine if we are using the
internal PHY, for which there are simpler and more robust methods:
Rewrite (and rename) the existing function to simply lookup the DT node
that "phy-handle" points to, using the device's DT node.
Then check whether the parent of that PHY node is using an "H3 internal
MDIO" compatible string. If we ever get another internal MDIO bus
implementation, we will probably need code adjustments anyway, so this
is good enough for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The error handling in recv() is somewhat broken, for instance
good_packet isn't really used, and it's hardly readable. Also we try
to check for short or too big packets, but those are actually filtered
out by the hardware.
Simplify the whole routine and improve the error handling:
- Bail out early if the current RX descriptor is not ready.
- Enable propagation of runt, huge and broken packets.
- Check for runt and huge packets, and return 0 to indicate this.
This will force the framework to call free_pkt for cleanup.
- Avoid aligning the packet buffer for invalidation again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC soft reset routine was subtly broken, using an open coded
timeout routine without any actual delay.
Remove the unneeded initial reset bit read, and call wait_for_bit_le32()
to handle the timeout correctly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When iterating over all RX/TX buffers, we were using a rather long "idx"
control variable, which lead to a nasty overlong line.
Replace "idx" with "i" to avoid this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To meet the current alignment requirements for our cache maintenance
functions, we were explicitly aligning the *arguments* to those calls.
This is not only ugly to read, but also wrong, as we need to make sure
we are not accidentally stepping on other data.
Provide wrapper functions for the common case of cleaning or
invalidating a descriptor, to make the cache maintenance calls more
readable. This fixes a good deal of the problematic calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There is no reason to invalidate a TX descriptor before we are setting
it up, as we will only write to a field.
Remove the not needed invalidate_dcache_range() call.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When we initialise the TX descriptors, there is no need yet to clean
them all to memory, as they don't contain any data yet. Later we will
touch and clean each descriptor anyway.
However we tell the MAC about the beginning of the chain, so we have to
clean at least the first descriptor, to make it clear that this is empty
and there are no packets to transfer yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Before we initialise the RX descriptors, there is no need to *clean*
them from the cache, as we touch them for the first time.
However we should cover the case that those buffers contain dirty cache
lines, which could be evicted and written back to DRAM any time later,
in the worst case *after* the MAC has transferred a packet into them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC driver contains a lot of magic bits, although the manuals
and the Linux driver have all names for them.
Define those names and use them when programming the registers.
Also this replaces a lot of readl/mask/writel operations with the much
easier-to-read setbits_le32() macro.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Apparently due to copying from some older or converted driver, the
sun8i_emac driver contains pointless wrapper functions to bridge
between a legacy driver and the driver model.
Since sun8i_emac is (and always was) driver model only, there is no
reason to have those confusing wrappers. Just remove them, and use
the driver model prototypes directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When preparing the register value for the MDIO command register, we
start with a zeroed register, so there is no need to mask off certain
bits before setting them.
Simplify the sequence, and rename the variable to a more matching
mii_cmd on the way.
Also the open-coded time-out routine can be replaced with a much safer
and easier-to-read call to wait_for_bit_le32().
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When initialising the TX DMA descriptors, we mostly chain them up,
but of course don't know about any data or its length yet.
That means they are still invalid, and the OWN bit should NOT be set
yet.
In fact when we later tell the MAC about the beginning of the chain,
and enable TX DMA in the start() routine, the MAC will start fetching
TX descriptors prematurely, as it can be seen by dumping the TX_DMA_STA
and TX_DMA_CUR_DESC registers.
Clear the owner bit, to not give the MAC the wrong illusion that it
owns the descriptors already.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When phy_startup() returns with an error, because there is no link or
the user interrupted the process, we shall stop the _start() routine
and return with an error, instead of proceeding anyway.
This fixes pointless operations when there is no Ethernet cable
connected, for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When partitions are not available on a device the command stm32prog raises
an error but a device can have no partition to check in init_device()
and the command need to continue to the next part_id.
This patch correct an issue for ram0 target, when block_dev and mtd
are NULL.
For example with the simple flashlayout file:
Opt Part Name Type Device Offset Binary
- 0x01 fsbl Binary none 0x0 tf-a-serialboot.stm32
- 0x03 ssbl Binary none 0x0 u-boot.stm32
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSytem ram0 0xC4000000 stm32mp157f-ev1.dtb
Fixes: ffc405e63b ("stm32mp: stm32prog: add upport of partial update")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate CONFIG_CMD_ELF to accept the command "bootelf".
This patch simplifies the file stm32mp defconfig, as we have
no reason to deactivate this command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate CONFIG_CMD_IMPORTENV to accept the command "env import".
This command is useful in script to include some variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the STM32MP1 RNG driver in the list of drivers supported by
the STMicroelectronics STM32MP15x series.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add files and directories regex "stm32" and "stm" in "ARM STM STM32MP"
platform to avoid missing files or drivers supported by the
STMicroelectronics series STM32MP15x.
This patch adds the rules already used in Linux kernel for
ARM/STM32 ARCHITECTURE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Cosmetic update of gpio.h:
- remove enumerate: stm32_gpio_port, stm32_gpio_pin
because STM32_GPIO_XXX values are unused
- move STM32_GPIOS_PER_BANK in stm32_gpio.c
as its value is IP dependent and not arch dependent
No functional change as number of banks and number of gpio by banks
is managed by device tree since since DM migration and
commit 8f651ca60b ("pinctrl: stm32: Add get_pins_count() ops").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In case the KS8851 has external EEPROM attached to it, do not set
eth1addr at all. The network stack will read the MAC out of the
KS8851 and set eth1addr accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>