The default values for 'addip' and 'norargs' changed per customer
request. Everything else cleaned up to fit into 80 symbol line.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Commit 29c6fbe047 broke
building for 83xx boards with USB support:
ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43: error: 'CONFIG_SYS_FSL_USB_ADDR' undeclared (first use in this function)
ehci-fsl.c:43: error: (Each undeclared identifier is reported only once
ehci-fsl.c:43: error: for each function it appears in.)
make[1]: *** [ehci-fsl.o] Error 1
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If a NOR flash is write protected it can not be initialized/detected so
add the ability for boards to skip NOR initialization on bootup. A
board can skip NOR initialization by implementing the
board_flash_wp_on() function.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: sr@denx.de
Acked-by: Stefan Roese <sr@denx.de>
Add missing codes according to original datasheet.
This patch also makes ftrtc010 could be adapted to PCLK and EXT_CLK.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.
Signed-off-by: Steve Sakoman <steve.sakomanlinaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
This patch matches the poll interval (1 millisecond) and timeout (1 second)
used in the linux driver. It also adds a return value of 0 in the event of
a timeout error and cleans up some formatting errors in that section of the
code.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
Commit 0ad7f0950a [ppc4xx: cleanup
default environment for AMCC boards] broke the default env for
many PPC4xx boards. The '\0' character got removed at the end
of some environment commands like "update". This patch adds the
missing '\0' characters again.
Signed-off-by: Stefan Roese <sr@denx.de>
Until now, the Sequoia RAM-booting image disabled NOR flash support
as this image was mainly created for NAND-only boards. This patch
now enables NOR flash support for this RAM-booting version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Add CONFIG_POST_UART to implement a board specific UART POST test.
This is done since lwmon5 needs to set POST_ALWAYS to run this
test on each reboot. And we don't want to change the default
behavious of this this.
Signed-off-by: Stefan Roese <sr@denx.de>
On an XPedite5370 over 11KBytes were saved:
Before:
text data bss dec hex filename
332456 33364 33476 399296 617c0 ./u-boot
After:
text data bss dec hex filename
321075 33836 33476 388387 5ed23 ./u-boot
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On an XPedite5170 over 11KBytes were saved:
Before:
text data bss dec hex filename
319488 28700 33204 381392 5d1d0 ./u-boot
After:
text data bss dec hex filename
307663 29144 33204 370011 5a55b ./u-boot
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously io_sel=0xe incorrect stated PCIE1 was enabled. Also add
support for the mpc8640's PCIE2 interface.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update to use the recent, common FSL PCI initialization code.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: sr@denx.de
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update to use the recent, common FSL PCI initialization code.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: joe.hamman@embeddedspecialties.com
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update to use the recent, common FSL PCI initialization code.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some OSes require that secondary cores not be initialized when they
are booted (eg VxWorks). By default when U-Boot is compiled with the
CONFIG_MP option all secondary cores are brought out of reset and held
in spinloops. Setting the "mp_holdoff" environment variable to 'yes'
or '1' will cause U-Boot to leave secondary cores in their default
state.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When DDR controller interleaving is eabled and less than all bank (chip-select)
interleaving is seletected, the unused chip-select should be disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
800, 900, 1000, 1200MT/s data rate parameters are added for fixed sdram
setting. SPD based parameters and fixed parameters can be toggled by hwconfig.
To use fixed parameters,
hwconfig=fsl_ddr:sdram=fixed
To use SPD parameters,
hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using PIC TFRR register for post word load/store for generic MPC85xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The memory test is performed after DDR initialization when U-boot stills runs
in flash and cache. On recent mpc85xx platforms, the total memory can be more
than 2GB. To cover whole memory, it needs be mapped 2GB at a time using a
sliding TLB window. After the testing, DDR is remapped with up to 2GB memory
from the lowest address as normal.
If memory test fails, DDR DIMM SPD and DDR controller registers are dumped for
further debugging.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A worker function setup_ddr_tlbs_phys() is introduced to implement more
control on physical address mapping.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The device tree (fdt) must always exist in within the bootmap (usually the
first 16MB of RAM). If it doesn't, then boot_relocate_fdt() will allocate
an LMB region in the bootmap and copy the fdt into that region. It will
also increase the size of the fdt.
If the fdt is already in the bootmap, then previously the memory was just
reserved. There was no contingency if the reservation failed, however.
By always allocating an lmb region and copying/resizing the fdt into that
region, the code is simplified and the memory region is always allocated
properly.
Also change the types of some variables to avoid some typecasts.
Signed-off-by: Timur Tabi <timur@freescale.com>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a common helper that will set the PHY connection type based on enum.
We use this on eTSEC, UCC, and will with Fman in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Have a common enum for phy types that we use in the UCC driver. We will
also use this enum for dealing with phy connection fixup in the device
tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Last commit 3831530dcb7b71329c272ccd6181f8038b6a6dd0a was intended
"explicitly specify FAT12/16 root directory parsing buffer size, instead
of relying on cluster size". Howver, the underlying function requires
the size of the buffer in blocks, not in bytes, and instead of passing
a double sector size a request for 1024 blocks is sent. This generates
a buffer overflow with overwriting of other structure (in the case seen,
USB structures were overwritten).
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Mikhail Zolotaryov <lebon@lebon.org.ua>
Commit a6bd9e8 "FDT: Add fixup support for multiple banks of memory"
removed code but forgot to remove the variables used by it, resulting
in warnings:
fdt_support.c: In function 'fdt_fixup_memory_banks':
fdt_support.c:399: warning: unused variable 'sizecell'
fdt_support.c:399: warning: unused variable 'addrcell'
Remove the declarations, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host
Controller Interface Specification for Universal Serial Bus" (Rev.
1.0, March 12, 2002) defines additional fields which were missing in
U-Boot's struct qTD; as these are also present in recent versions of
struct ehci_qtd in the Linux kernel, we add them here, too.
This fixes some nasty memory corruption problems.
Reported-by: Dan Lykowski <lykowdk@gmail.com>
See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
The usage and help for the fpga command is wrong and incomplete,
and the parameters are not checked before to be passed to the
underlying subfunction.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The "options" field at the moment is only documented in the changelog
which isn't terribly useful to people without git.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for the HP Jornada flashboards
that were made in 2008. Older flashroms should work if
memory registers are adjusted.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Adpted for TEXT_BASE -> CONFIG_SYS_TEXT_BASE rename.
Removed now redundant board/jornada/config.mk file.
Removed unused empty jornada_init() function to silence
"jornada.c:35: warning: 'jornada_init' defined but not used"
Signed-off-by: Wolfgang Denk <wd@denx.de>
Boards often have a reserved size limit on the flash where they're stored.
Sometimes during upgrades or config changes, those limits are exceeded,
but no one notices until they try to upgrade and the limit screws things
up. Either not enough of U-Boot is written to flash (and so the reboot
fails), or too much is written (and so things after it get clobbered).
So allow boards to declare a size limit (in bytes) and have the build
system check it while building.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Call fec_set_hwaddr in init routine to setup MAC address so when ethaddr is set
late via setenv the change will propagate to the hw.
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Ben Warren <biggerbadderben@gmail.com>
