This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
Do not allow to overwrite it when video is enabled.
Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This file documents when to build for da850evm and when to build for
da850_am18xxevm. It also documents how to write the u-boot.ais file to
persistent storage (such as SPI), in some cases as well as how to write
a recovery image.
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
fecmxc_mii_postcall() is specific to the KSZ9021 PHY on m28evk and
should not be used on mx28evk, which has LAN8270 instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
The NAND Flash of the KARO TX25 board is a Samsung K9F1G08U0B with 25-ns R/W
cycle times. However, the NFC clock for this board was set to 66.5 MHz, so using
the NFC driver in symmetric mode (i.e. 1 NFC clock cycle = 1 NF R/W cycle)
resulted in NF R/W cycle times of 15 ns, hence corrupted NF accesses.
This patch fixes this issue by setting the NFC clock to the highest frequency
complying to the 25-ns NF R/W cycle times specification, i.e. 33.25 MHz.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Gachet <Daniel.Gachet@hefr.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG
information.
If this data is not present, the kernel misconfigures the TZIC, which results in
the timer interrupt handler never being called, so the kernel deadlocks while
calibrating its delay.
Suggested-by: Greg Topmiller <Greg.Topmiller@jdsu.com>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the onboard eSDHC MMC controller. The hardware on the
MPC8308RDB has the following errata:
- ESDHC111: manual asynchronous CMD12 is broken
- DMA is broken (PIO works)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
[added include fsl_esdhc header to prevent implicit declarations of
fsl_esdhc_mmc_init() and fdt_fixup_esdhc()]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The SPI pins are routed to header J8 for testing SPI functionality. A
Spansion flash has been wired up and tested on this header.
This patch breaks support for the second TSEC interface, since the GPIO
pin used as a chip select is pinmuxed with some of the TSEC pins.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This board is the only board that still sticks to OneNAND IPL.
Remove this board, since we have SPL around for a while and
OneNAND is well supported in the SPL framework. The board can
be revived if necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tom Rini <trini@ti.com>
After removing the Apollon board, remove the OneNAND IPL too.
There are no users for it any more.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <promsoft@gmail.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Support for multiple soft I2C buses.
Multibus I2C support is achieved by defining get_multi_{sda|scl}_pin
functions to switch between multiple "soft" I2C buses.
Common definition of I2C_X I2C buses is provided at <i2c.h>.
TEST HW:
Samsung's Exynos4210 evt.0.1 - Trats development board
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch configure at91sam9x5's EBI drive I/O. Without this, When SD card boot, the nand flash read/write are not stable. Which will cause kernel MTD test fail (Since mainline kernel doesn't configure the EBI register).
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch is derived from an older patch provided by atmel in its
buildroot-avr32-v3.0.0.tar.bz2
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Move board specific function to board_init function in board/ folder
Remove externs from generic board.c
Use board_init_f function in board.c file.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Ventana always pulls in files from the Seaboard directory, so needs to
mkdir $(obj)../seaboard unconditionally. This fixes:
git clean -f -d -x
./MAKEALL ventana
"MAKEALL -s tegra20" passes without this change, because Seaboard
happens to be built before Ventana, and hence the directory has already
been created.
I believe the mkdir is only needed for out-of-tree builds, since the
seaboard directory is part of the source tree. However, since we always
build an SPL for Tegra now, which I believe is effectively an out-of-tree
build, we will always need this at some time. The overhead of just
uncondtionally executing the mkdir is minimal, and simplifies the
Makefile, since we don't need to code up the exact minimal condition to
execute the mkdir.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This commit enables NAND support on the Tamonten Evaluation Carrier and
adds the corresponding device tree nodes. Furthermore, the U-Boot
environment can now be stored in NAND.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a flash node to handle the NAND, including memory timings and
page / block size information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move highly platform dependant code into its own functions to reduce the
number of #ifdefs in lcd_display_bitmap
To avoid breaking the mcc200 board which does not #define
CONFIG_CMD_BMP, this patch also implements bmp_display() for mcc200.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
