This commit adds the EFI_TCG2_PROTOCOL.SubmitCommand
required in the TCG PC Client PFP spec.
SubmitCommand enables to send the raw command to the TPM device.
To implement this api, tpm2_submit_command() is added
into tpm-v2.c.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Calling unaligned/access-ok.h version of put_unaligned_le64()
causes data abort in arm 32-bit QEMU.
The similar issue also occurs in linux kernel,
unaligned/access-ok.h is no longer used in linux kernel[1].
This commit uses the unaligned/be_byteshift.h and
unaligned/le_byteshift.h helper instead of unaligned/access-ok.h.
[1]https://lore.kernel.org/all/20210507220813.365382-8-arnd@kernel.org/
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As we discussed in ML, currently a device tree is the only place
to store public keys for capsule authentication. So __weak is not
necessary for now.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide human readable descriptions of the speed nodes instead of the name
of constants from the code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The related boards have been removed four years ago already, in
commit 98f705c9ce ("powerpc: remove 4xx support"), so this README
file is not required anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The PPC440 support has been removed in commit 98f705c9ce
("powerpc: remove 4xx support"). This patch removes this obsolete
file as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
CONFIG_BOARD_LATE_INIT
CONFIG_DISPLAY_BOARDINFO
CONFIG_DISPLAY_BOARDINFO_LATE
Signed-off-by: Tom Rini <trini@konsulko.com>
When building a system that has both TPL and SPL_OS_BOOT, code which
tests for CONFIG_SPL_OS_BOOT will be built and enabled in TPL, which is
not correct. While there is no CONFIG_TPL_OS_BOOT symbol at this time
(and likely will not ever be) we can use CONFIG_IS_ENABLED(OS_BOOT) in
these common paths to ensure we only compile these parts in the SPL
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
For the symbols which are both hard-coded as enabled and used, move to
Kconfig. The rest of the CONFIG_YAFFS namespace is unselected anywhere,
so we leave it as is.
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of hardcoding the watchdog for reset, and the PMIC for poweroff,
use the sysreset framework to manage the available poweroff/reset
backends. This allows (as examples) using the PMIC to do a cold reset,
and using a GPIO to power off H3/H5 boards lacking a PMIC. Furthermore,
it removes the need to hardcode watchdog MMIO addresses, since the
sysreset backends can be discovered using the device tree.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The sysreset uclass unconditionally provides a definition of the
reset_cpu() function. So does the sunxi board code. Fix the build with
SYSRESET enabled by omitting the function from the board code in that
case. The code still needs to be kept around for use in SPL.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add an option to automatically register watchdog devices with the
wdt_reboot driver for use with sysreset. This allows sysreset to be a
drop-in replacement for platform-specific watchdog reset code, without
needing any device tree changes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently, the wdt_reboot driver always gets its watchdog device
reference from an OF node. This prevents selecting a watchdog at
runtime. Move the watchdog device reference to the plat data, so
the driver can be bound with the reference pre-provided. The
reference will still be acquired from the OF node if it is not
already provided.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
These driver probe functions are not (and should not be) called from
outside the respective driver source files. Therefore, the functions
should be marked static.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
None of the sysreset drivers do anything beyond providing sysreset
uclass ops. They should depend on the sysreset uclass.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- pci_mvebu: Fix access to config space and PCIe Root Port (Pali)
- a37xx: pci: Program the data strobe for config read requests (Pali)
- kwboot: Misc improvements and fixes (Pali)
When allocate the GPD ring, and tell its address to the controller, then
the driver starts or resumes the QMU, the controller will try to access
the first GPD, so need flush the first one to avoid wrong GPD status.
Reported-by: Xin Lin <Xin.Lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
According to the Armada 3720 Functional Specification Data Strobe applies
for both read and write config requests.
Data strobe bits configure which bytes from the start address should be
returned for read request. Set value 0xf (all 4 bits) into Data Strobe
register to read all four bytes from specified 32-bit config space
register. Same value for Data Strobe register is programmed by Linux
pci-aardvark.c driver for config read requests.
Without this patch pci-aardvark driver sets data strobe register only
during config write operations. So any followup config read operations
could result with just partial datai returned (if previous write operation
was not 32-bit wide). This patch fixes it and ensures that config read
operations always read all bytes from requested register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
After successful transfer of whole image only two things can happen:
- BootROM starts execution of data block, which changes UART baudrate
back to 115200 Bd,
- board crashes and causes CPU reset
In both cases UART baudrate is reset to the default speed. So there is
no need to send special magic sequence to inform kwboot that baudrate is
going to be reset and kwboot does not need to wait for this event and
can do it immediately after BootROM acknowledges end of xmodem transfer.
Move ARM code for sending magic sequence from main baudrate change
section to binhdr_pre section which is executed only before changing
baudrate from the default value of 115200 Bd to some new value. Remove
kwboot code waiting for magic sequence after successful xmodem transfer.
Rationale: sometimes when using very high UART speeds, magic sequence is
damaged and kwboot fails at this last stage. Removal of this magic
sequence makes booting more stable.
Data transfer protocol (xmodem) is using checksums and retransmit, so it
already deals with possible errors on transfer line.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The ARM code we inject into the image to change baudrate back to the
default value of 115200 Baud, which is run after successful UART transfer
of the whole image, cannot use stack as at this stage stack pointer is not
initialized yet.
Stack can only be used when BootROM is executing binary header, to
preserve state of registers, since BootROM expects that.
Change the ARM baudrate code to not use stack at all and put binary
header specific pre + post code (which stores and restores registers) into
separate arrays.
The baudrate change code now jumps at it's end and expects that there is
either code which returns to the BootROM or jumps to the original exec
address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Older Armada SoCs have custom ARMv5te compatible core which does not
support movt instruction. So replace mov + movt instruction pair used for
immediate move construction by mov + orr instructions which are supported
also by ARMv5te.
After this change kwboot ARM code should be compatible with any 32-bit ARM
core compatible by ARMv2 or new. At least GNU AS does not throw any error
or warning.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Increase loop cycles from 600000 to 2998272, which should increase delay
from 1ms to about 5ms on 1200 MHz CPU.
The Number 2998272 was chosen as the nearest value around 3000000 which can
be encoded into one ARM mov instruction. It avoids usage of movt instruction
which is not supported by ARMv5te cores.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Kwboot puts each xmodem packet to kernel queue, then waits until all bytes
of that packet are transmitted over UART and then waits for xmodem reply
until it is received into kernel queue.
If some reply is received during the time we are waiting until all bytes
are transmitted, then kernel puts them into the queue and returns it to
kwboot in next read() call.
So there is no need to wait (with tcdrain() function) until all bytes from
xmodem packet are transmitted over UART, since any reply received either
during that time or after is returned to kwboot with the next read().
Therefore do not call tcdrain() after each xmodem packet sent. Instead
directly wait for any reply after putting xmodem packet into write kernel
queue.
This change could speed up xmodem transfer in case tcdrain() function waits
for a longer time.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
After the trasfer of last header packet, it is possible that baudrate
change pattern is received, and also that NAK byte is received so that
the packet should be sent again.
Thus we should not clear the baudrate change state when sending retry
of that packet.
Move code for initializing state variables from kwboot_xm_recv_reply()
to kwboot_xm_sendblock().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently when kwboot receive some garbage reply which does not understand,
it waits 1s before it tries to resend packet again.
The most common error on UART is that receiver sees some bit flipped which
results in invalid reply.
This behavior slows down xmodem transfer over UART as basically on every
error kwboot is waiting one second.
To fix this, try to resend xmodem packet for first 3 attempts immediately
without any delay. If broken reply is received also after the 3 attempts,
continue retrying with 1s delay like it was before.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch does not change behavior of the code, just allows to implement
new changes more easily.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Size of the header stored in kwbimage may be larger than real used size in
the kwbimage header. If there is unused space in kwbimage header then use
it for growing it. So update code to calculate used space of kwbimage
header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This ensures that kwboot_img_grow_hdr() function still sees valid kwbimage
header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Expression (hdrsz % KWBOOT_XM_BLKSZ) is non-zero therefore expression
(KWBOOT_XM_BLKSZ - hdrsz % KWBOOT_XM_BLKSZ) is always less than value
KWBOOT_XM_BLKSZ. So there is no need to add another modulo. Also rename
variable `offset` to `grow` which better describes what is stored in
this variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
It is hard to debug why kwboot is failing when the last message is
'Finishing transfer' and no additional output. So show verbose message when
kwboot finished transfer and is waiting for baudrate change magic sequence.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
For kwbimage v1, tell BootROM to send BootROM messages to UART port number
0 (used also for UART booting) with default baudrate (which should be
115200) and do not touch UART MPP configuration.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
If data part of image is modified, update 4-byte data checksum.
It looks like A385 BootROM does not verify this checksum for image
loaded via UART, but we do not know if other BootROMs are also ignoring
it. It is always better to provide correct checksum.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Some vendor U-Boot kwbimage binaries (e.g. those for A375) have load
address set to zero. Therefore it is not possible to inject code which
changes baudrate back to 115200 Bd before the data part.
So instead inject it after the data part and change kwbimage execution
address to that offset. Also store original execution address into
baudrate change code, so after it changes baudrate back to 115200 Bd, it
can jump to orignal address.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Data part of the image contains 4-byte checksum. Validate it when
processing the image.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
SPI image header and data parts do not have to be aligned to 128 byte
xmodem block size. So reserve additional memory for aligning header part
and additional memory for aligning data part.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Explicitly disable 2 stop bits by clearing CSTOPB flag, disable modem
control flow by clearing CRTSCTS flag and do not send hangup after closing
device by clearing HUPCL flag.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Explicitly zero out the rfds fd_set with FD_ZERO() before using it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a pci driver, not an eth driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
