These peripherals should not be at the top level, since they exist inside
the PCI bus. We don't have a full device tree node for pci yet, but we
should at least put it at the right level.
Signed-off-by: Simon Glass <sjg@chromium.org>
Set up all the remaining pieces of the LPC (low-pin-count) peripheral in
PCH (Peripheral Controller Hub).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some PCI functions cannot be auto-configured. Add a function to set up a
fixed BAR which can be used in these situations. Also add a function to read
the current address of a BAR.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this option so that we can configure the available PCI devices. Also
make sure that PCI is available early after relocation as we use it for
several other subsystems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards will want to do some setup before and after a PCI hose
is scanned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Define the reset base in config.mk so that it does not need to be calculated
twice in the link script. Also tidy up the START_16 and RESET_VEC_LOC values
to fit with this new approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some toolchains put the relocation data into separate sections. Adjust the
linker script to catch this case. Without relocation data, U-Boot will not
boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This normally indicates a problem which will prevent relocation from
functioning, resulting in a hang. Panic in this case to make it easier
to debug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is not needed. Remove it to improve the generic init sequence
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Device trees must be aligned to a 4-byte boundary. This was dropped in the
Kbuild conversion. Bring it back, and use 16-byte alignment for good
measure.
Signed-off-by: Simon Glass <sjg@chromium.org>
This new symbol may be defined by the compiler. If it is, avoid a compiler
warning when USE_STDINT is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is now required to add subdirectories in the x86 cpu Makefile. Add this
to fix a build breakage for chromebook_link.
Signed-off-by: Simon Glass <sjg@chromium.org>
128059b92 ("hush: fix segfault on syntax error") attempted to fix a
segfault on syntax errors, but it broke Ctrl-C handling, and the
assumption that it made, that rcode could not be -1, is incorrect.
Revert this change.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Benard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Ideally, the Linux kernel should get the hardware in its most
untouched state. For the most part, U-Boot does not reset the various
subsystems it touches before boot, and usually Linux deals with it, but
on some boards (cm_fx6) the Linux kernel fails to detect the ssd
correctly if sata is used by U-Boot.
Power off sata on OS boot so that Linux will have a clean state to work
with.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Provide board specific implementation for sata stop command for
cm_fx6.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Implement sata stop command.
This introduces the __sata_stop() weak function, which mirrors
the weak __sata_initialize() function, giving users the option of
undoing the custom steps performed in overrides of sata_initialize().
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
gw_ventana can boot from SPI or NAND and both of these interfaces boot from
the same 0x400 offset.
This means that we could simplify the code and replace the custom gw_ventana.cfg
with the generic spl_sd.cfg, as it provides the same boot offset of 0x400.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Older Linux kernels will not properly boot in hyp mode, add support for a
bootm_boot_mode environment variable, which can be set to "sec" or "nonsec"
to force booting in secure or non-secure mode when build with non-sec support.
The default behavior can be selected through CONFIG_ARMV7_BOOT_SEC_DEFAULT,
when this is set booting in secure mode is the default. The default setting
for this Kconfig option is N, preserving the current behavior of booting in
non-secure mode by default when non-secure mode is supported.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For similar reasons to why the Linux Kernel has an EXPERT option, we too
want an option to allow for tweaking of some options that while normally
should remain hidden, may need to be changed in some cases.
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <trini@ti.com>
Change the internal sandbox functions to use loff_t for file offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change the internal EXT4 functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update common/spl/spl_ext.c]
Signed-off-by: Tom Rini <trini@ti.com>
Change the internal FAT functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Fix fs/fat/fat.c for min3 updates]
Signed-off-by: Tom Rini <trini@ti.com>
Enable md5sum to obtain the MD5 of the read and written files to check
their contents for validity.
Use map_sysmem() to map buffer in a sandbox environment.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This fixes following warning when compiled with MIPS64
common/board_f.c: In function 'display_text_info':
common/board_f.c:150:2: warning: format '%X' expects argument i
of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat=]
debug("U-Boot code: %08X -> %08lX BSS: -> %08lX\n",
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
