Process errors from command via cmd_process_error() as is done on Versal.
When internal function returns different number then CMD_RET_SUCCESS(0),
CMD_RET_FAILURE(1) or CMD_RET_USAGE(-1) shell react on these errors by
throwing an error like
"exit not allowed from main input shell." that's why use
cmd_process_error() to make sure that error code is all the time correct.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d511935ba10daf95c70996fae6e6ffc374efffa0.1685618464.git.michal.simek@amd.com
The Xilinx ZynqMP SoC has a hardened display pipeline named DisplayPort
Subsystem. It includes a buffer manager, blender, an audio mixer and a
DisplayPort source controller (transmitter). The DisplayPort controller can
source data from memory (non-live input) or the stream (live input). The
DisplayPort controller is responsible for managing the link and physical
layer functionality. The controller packs audio/video data into transfer
units and sends them over the main link. The link rate and lane counts can
be selected based on the application bandwidth requirements. The
DisplayPort pipeline consists of the DisplayPort direct memory access (DMA)
for fetching data from memory. The DisplayPort DMA controller (DPDMA)
supports up to six input channels as non-live input.
This driver supports the DisplayPort Subsystem and implements
1)640x480 resolution
2)RGBA8888 32bpp format
3)DPDMA channel 3 for Graphics
4)Non-live input
5)Fixed 5.4G link rate
6)Tested on ZCU102 board
There will be additional work to configure GT lines based on DT, higher
resolutions, support for more compressed video formats, spliting code to
more files, add support for EDID, audio support, using clock framework for
all clocks and in general code clean up.
Codevelop-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/5c1567b63d0280dacc7efba2998857c399c25358.1684312924.git.michal.simek@amd.com
Add support for RGBA8888 32bpp format where pixels are picked in
32-bit integers, where the colors are stored in memory such that
R is at lowest address, G after that, B after that, and A last.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aa1de54b7d4ff46df6858f76d52634e0c5c71a4a.1684312924.git.michal.simek@amd.com
Store the driver data in the data section to make the data usable before
relocation. Additionally mark the driver data static to restrict the
access.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-5-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move the permission to change a config object message from
zynqmp_pmufw_load_config_object function to zynqmp_pmufw_node function
to simplify the code and check the permission only if required.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-4-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Remove the redundant child device bind from the driver bind function and
rely on the post_bind of the class which calls the same function.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-2-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Return a common -EACCES error value instead of a positive private error
value XST_PM_NO_ACCESS (2002) in zynqmp_pmufw_load_config_object
function if the config object is not loadable to simplify the error
checking.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20230523124215.30915-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Production version restarting platform version field from 0 that's why add
new calculation to be able to use different DT for these platforms.
Requested DT names for production silicons for IPP/SPP and EMU platform are
versal-net-ipp-rev2.0.dts and versal-net-emu-rev2.0.dts.
If platform version increase numbers revision can be even higher.
As of today platform version is 2 that's why expected is rev2.2.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/691e166b3cf2643d7edf482bda5500163eecb35a.1684311689.git.michal.simek@amd.com
For sf commands, when '0' length is passed for erase, update, write or
read, there might be undesired results. Ideally '0' length means nothing to
do.
So print 'ERROR: Invalid size 0' and return cmd failure when length '0' is
passed to sf commands. Same thing applies for nand commands also.
Example:
ZynqMP> sf erase 0 0
ERROR: Invalid size 0
ZynqMP> sf write 10000 0 0
ERROR: Invalid size 0
ZynqMP> sf read 10000 0 0
ERROR: Invalid size 0
ZynqMP> sf update 1000 10000 0
ERROR: Invalid size 0
ZynqMP>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230516115236.22458-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add fallthrough statement in switch case to fix the sparse warning.
In function 'zynqmp_clk_get_rate': warning: this statement may
fall through [-Wimplicit-fallthrough=]
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230519113816.22083-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Read boodmode register using versal_net_get_bootmode() in board_late_init
and prepare corresponding distro boot command sequence based on it.
versal_net_get_bootmode() will be changed to use smc calls later, but
for now directly reads the register.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230516144753.30869-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The function fdtdec_board_setup() is called early and adds the overlay
from ATF to the u-boot device tree. That is necessary so that u-boot
doesn't use reserved memory.
Linux also needs to know about that reserved memory so the overlay from
ATF needs to be aplied on the linux device tree as well.
This commit makes sure that the ATF overlay is applied to both device trees.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
The board comes with SMSC LAN8710A PHY, enable matching driver.
Enable DM_ETH_PHY in the process to start using DM drivers more.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
---
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add compatible values to Ethernet PHY subnodes representing SMSC
LAN8710A PHYs on RZ/A1 and R-Mobile A1 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Ported from Linux kernel commit 1c65ef1c71e473c00f2a7a1b9c140f0b4862f282 .
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/247dc2074dae149af07b6d014985ad30eb362eda.1631174218.git.geert+renesas@glider.be
---
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
In case RX error occurs, and the RD_RFE bit is set, the descriptor
is never returned back to the queue. Make sh_eth_recv_start return
zero length in this case so that the descriptor can be released
and pushed back to the list. Also return the more appropriate
-EAGAIN instead of -EINVAL if the descriptor is not ready yet.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
U-Boot writes to RX packets when constructing replies.
This can cause stale cached data to be written to RX
buffer while we're receiving a packet. This causes RX
packet corruption because we invalidate the cache right
before processing the packet. Invalidate packet buffer
cache when preparing RX descriptor as well. This seems
to fix RX packet drops with high RX traffic.
While at it flush the descriptors right before enabling
RX/TX in sh_eth_tx_desc_init/sh_eth_rx_desc_init callbacks
when they are ready instead of flushing after allocation.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The common code is now capable of handling reset GPIO associated
with PHY. Drop the local ad-hoc code in favor of common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The common code is now capable of handling reset GPIO associated
with PHY. Drop the local ad-hoc code in favor of common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
These two properties are used by various DTs in place of
current reset-assert-us/reset-deassert-us , handle both .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In case a new PHY is created and DM_ETH_PHY is enabled, bind a
generic PHY driver from ETH_PHY uclass to the PHY to have a
matching DM representation of that PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The phy_connect_dev() is legacy API, now that there are no users,
make it internal to phy.c and unpublish it from headers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use new U-Boot phy_connect() API which also supports fixed PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The eth_phy_reset() is not used outside of this file, staticize it.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds 4-byte address mode support. Because traditional access
based on FIFO/shift register, it's complex to specify information like
opcode, address length, dummy bytes etc to flash. Replace the traditional
access by spi-mem layer which is essential to make 4-byte address mode
support possible.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Support RPC SPI on R-Car Gen4 R8A779F0 S4 and R8A779G0 V4H SoCs.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Squash S4 and V4H patches, fix brackets around STRTIM2]
Enable support for parsing and auto discovery of parameters for
SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
tables as per JESD216 standard.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Make SFDP the default unconditionally
Move strobe delay setting code into extra function and reflect the latest
setting in datasheet (R-Car Gen3 v2.20, R-Car V3U v0.50).
i.e. STRTIM[2:0] should be set to 110 (RCar M3-W) or 111 (Other products)
This is also a preparation for new R-Car Gen4 SoC which has 4-bits STRTIM
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Fix for RZ/A1
Two sets of FWU updates from Jassi Brar. First:
The patchset reduces ~400 lines of code, while keeping the functionality same and making
meta-data operations much faster (by using cached structures).
Issue:
meta-data copies (primary and secondary) are being handled by the
backend/storage layer instead of the common core in fwu.c (as also noted by
Ilias) that is, gpt_blk.c manages meta-data and similarly raw_mtd.c will have
to do the same when it arrives. The code could by make smaller, cleaner and
optimised.
Basic idea:
Introduce .read_mdata() and .write_mdata() in fwu_mdata_ops that simply
read/write meta-data copy. The core code takes care of integrity and redundancy
of the meta-data, as a result we can get rid of every other callback
.get_mdata() .update_mdata() .get_mdata_part_num() .read_mdata_partition()
.write_mdata_partition() and the corresponding wrapper functions thereby making
the code 100s of LOC smaller.
Get rid of fwu_check_mdata_validity() and fwu_mdata_check() which expected
underlying layer to manage and verify mdata copies.
Implement fwu_get_verified_mdata(struct fwu_mdata *mdata) public function that
reads, verifies and, if needed, fixes the meta-data copies.
Verified copy of meta-data is now cached as 'g_mdata' in fwu.c, which avoids
multiple low-level expensive read and parse calls.
gpt meta-data partition numbers are now cached in gpt_blk.c, so that we don't
have to do expensive part_get_info() and uid ops.
And second:
Introduce support for mtd backed storage for FWU feature and enable it on
Synquacer platform based DeveloperBox.
Just like fwu_plat_get_update_index, provide a default/weak
implementation of fwu_plat_get_bootidx. So that most platforms
wouldn't have to re-implement the likely case.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
