If the clock framework provides the driver with valid clock,
enable them, otherwise the SCIF might not work if the clock
are not enabled prior to the driver probe.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for obtaining PHY reset GPIO from DT and toggling it
before configuring the PHY to put the PHY into defined state.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The SDxCKCR must be configured correctly, otherwise the SDIF can be
unstable. This is done in board files thus far, but those are going
away, so move the setting of SDxCKCR into the correct place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Place the stack right below U-Boot so it's not in the way in case
U-Boot grows too much.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Just move those config options from macros to configs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7796 XHCI USB nodes are missing from r8a7796 dtsi, add them.
These nodes don't come from mainline Linux, yet the DT binding is
similar enough to R8A7795 which already has those in mainline and
once the nodes hit mainline, this DT should be resynched.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the EHCI generic driver, which is superior to ad-hoc SoC specific one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the EHCI generic driver, which is superior to ad-hoc SoC specific one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In order to use ehci-generic driver, move the configuration of HSUSB
block into the board file. This configuration should not have been in
the Gen3 EHCI USB driver in the first place, so move it to the board
file until there is a proper infrastructure and driver for the HSUSB
block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In order to use ehci-generic driver, move the configuration of HSUSB
block into the board file. This configuration should not have been in
the Gen3 EHCI USB driver in the first place, so move it to the board
file until there is a proper infrastructure and driver for the HSUSB
block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7796 EHCI USB nodes are missing from r8a7796 dtsi, add them.
These nodes don't come from mainline Linux, yet the DT binding is
similar enough to R8A7795 which already has those in mainline and
once the nodes hit mainline, this DT should be resynched.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.13,
commit 569dbb88e80deb68974ef6fdd6a13edb9d686261 . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With support for overlays and calling the -@ flag to dtc we need to have
at least 1.4.3 available now.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
common/spl/spl_fit.c:201:12: warning: passing argument 4 of ‘gunzip’
from incompatible pointer type [-Wincompatible-pointer-types]
src, &length))
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Jean-Jacques Hiblot <jjhiblot@ti.com>
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This file is imported from linux kernel v4.13
Add device tree support for STM32H743 evaluation board.
This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS and FS
_ I2 C compatible serial interface
_ RTC with rechargeable backup battery
_ SAI Audio DAC
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM, 1Mx16bit SRAM and 8Mx16bit NOR Flash
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Potentiometer
_ 4 colored user LEDs
_ Reset, wakeup, tamper or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
Power jack
3 USB with Micro-AB
RS-232 communications
Ethernet RJ45
FD-CAN compliant connection
Stereo headset jack including analog microphone input
2 audio jacks for external speakers
microSD™ card
JTAG/SWD and ETM trace
_ Expansion connectors:
Extension connectors and memory connectors for daughterboard
or wire-wrap board
_ Flexible power-supply options: ST-LINK USB VBUS or external
sources
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the support of reset and clock control
block (rcc) found on STM32 SoCs.
This driver is similar to a MFD linux driver.
This driver supports currently STM32H7 only.
STM32F4 and STM32F7 will be migrated to this rcc MFD driver
in the future to uniformize all STM32 SoCs already upstreamed.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is adapted from linux drivers/reset/reset-stm32.c
It's compatible with STM32 F4/F7/H7 SoCs.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
To add support for each SoC family, a SoC's specific
include/dt-binfings/mfd/stm32xx-rcc.h file must be added.
This patch only includes stm32h7-rcc.h dedicated for STM32H7 SoCs.
Other SoCs support will be added in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements basic clock setup, only clock gating
is implemented.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
Files include/dt-bindings/clock/stm32h7-clks.h and
doc/device-tree-bindings/clock/st,stm32h7-rcc.txt
will be available soon in a kernel tag, as all the
bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
STM32F7 and STM32H7 shares the same UART block, add
STM32H7 compatible string.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
STM32H7 SoCs uses the same pinctrl block as found into
STM32F7 SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Since we may jump to next stage like ATF/OP-TEE instead of U-Boot,
we need to stash the bootstage info before it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add usb_gadget_handle_interrupts(), board_usb_init(),
board_usb_cleanup() and g_dnl_board_usb_cable_connected()
callbacks needed for FASTBOOT support
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update ehci and ohci node's compatible string in order to
use ehci-generic and ohci-generic drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On STi 96boards, configure by default the micro USB connector
(managed by DWC3 hardware block) in peripheral mode.
This will allow to use fastboot feature.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable USB Host Networking support by enabling Ethernet/USB
adaptors support and by enabling some BOOTP flags
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is the generic phy driver for the picoPHY ports
used by USB2/1.1 controllers. It is found on STiH407 SoC
family from STMicroelectronics.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
reset-names property is needed to use the reset
API for STi sdhci driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use struct udevice* as input parameter. Previous
parameters are retrieved through plat and priv data.
This to prepare to use the reset framework.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
'default n' is the default anyway so it doesn't need to be specified
explicitly, and the rest of the file doesn't specify it either anywhere.
Drop it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This field is no longer used since the DM conversion. Drop it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This field is no longer used since the DM conversion. Drop it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This field has never been used as the driver has been DM-based since the
beginning. Drop it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These take the 'struct udevice *' as an argument, not the
'struct xilinx_pcie *` which is a local variable. Fix the comments to
match the code.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We have limited stack in SPL builds. Drop itrblock and move to
malloc/free of itr to move this off of the stack. As part of this fix a
double-free issue in fat_size().
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Rework to use malloc/free as moving this to a global overflows some SH
targets.
