The GW73xx-C revision and onward replaced the 5-port PCIe switch with a
4-port (dropping PCIe to one of the miniPCIe sockets) due to part
availability. This moved the PCI bus of the GbE eth1 device. Use a fixup
to adjust the dt accordingly so that local-mac-address assigned from dt
works on new revision boards.
While we are at it, rename 'blob' to 'fdt' for clarity.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This commit adds board support for i.MXRT1170-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT117x processor family.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
It seems that waiting only 10 ms after releasing LAN switch from reset
is not enough for the strapping pins to latch the requested values.
P6_MODE[0] is latched to 0 instead of 1.
Increasing the delay to 50 ms fixes this issue.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
$fdt_addr is mandatory for systems which provides DTB in HW (e.g. ROM) and
wishes to pass that DTB to Linux.
Turris Mox contains DTB binary in SPI NOR memory at "dtb" partition which
starts at offset 0x7f0000 and is 0x10000 bytes long.
Armada 3700 CPU does not allow mapping SPI NOR memory into physical address
space like on other architectures and therefore set $fdt_addr variable to
memory range in RAM and loads this DTB binary from SPI NOR in misc_init_r()
function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When rescue mode was activated reset also bootdelay env variable to its
default value. This will ensure that reset button works and starts rescue
mode also in the case when user changed bootdelay env variable to -1 (which
has meaning to not start autoboot).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Store serial number from atsha cryptochip into the serial# env variable.
U-Boot automatically puts content of this variable into the root device
tree property serial-number when booting Linux kernel. Refactor turris
atsha code and from turris_atsha_otp_get_serial_number() function returns
directly string suitable for printing or storing into device tree. Because
during different boot stages is env storage read-only, it is not possible
to always store serial number into env storage. So introduce a new function
turris_atsha_otp_init_serial_number() which is called at later stage and
which ensures that serial number is correctly stored into env.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
CPLD in load_default mode ignores watchdog reset signal. It does not reset
board when watchdog triggers reset signal.
Detect load_default mode by GPIO7 - LOAD_DEFAULT_N and delete watchdog
max6370 node from device to prevent registering driver for non-working
watchdog.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Perform long overdue conversion of ad-hoc FMC2 EBI bus initialization
to upstream FMC2 EBI driver. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The tests on CONFIG_DM_REGULATOR, added to avoid compilation issues, can
now be removed, they are no more needed since the commit 16cc5ad0b4
("power: regulator: add dummy helper").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
P1/P2 RDB boards have external max6370 watchdog connected to CPLD and this
watchdog is not deactivated on board reset. So if it is active during board
reset, it can trigger another reset when CPU is booting U-Boot. To prevent
possible infinite reset loop caused by external watchdog, turn it off
before reset.
Do it via a new board_reset_prepare() callback which is called from
do_reset() function before any reset sequence.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CPLD's system reset register is buggy and requires workaround in U-Boot.
So use this kind of board reset only when there is no other reset option.
Introduce a new board_reset_last() callback which is last-stage
board-specific reset and implement CPLD's system reset in this new
board_reset_last() callback instead of board_reset() callback.
Fixes: 20fb58fc5a ("board: freescale: p1_p2_rdb_pc: Implement board_reset()")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If watchdog timer was already set to non-disabled value then it means that
watchdog timer was already activated, has already expired and caused CPU
reset. If this happened then due to CPLD firmware bug, writing to wd_cfg
register has no effect and therefore it is not possible to reactivate
watchdog timer again. Watchdog starts working again after CPU reset via
non-watchdog method.
Implement this workaround (reset CPU when it was reset by watchdog) to make
watchdog usable again. Watchdog timer logic on these P1/P2 RDB boards is
connected to CPLD, not to SoC itself.
Note that reset does not occur immediately after calling do_reset(), but
after few ms later as real reset is done by CPLD. So it is normal that
function do_reset() returns. Therefore hangs after calling do_reset() to
prevent CPU execution of the rest U-Boot code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CPLD's system reset register on P1/P2 RDB boards is not autocleared after
flipping it. If this register is set to one in 100ms after reset starts
then CPLD triggers another CPU reset.
This means that trying to reset board via CPLD system reset register cause
reboot loop. To prevent this reboot loop, the only workaround is to try to
clear CPLD's system reset register as early as possible. U-Boot is already
doing it in its board_early_init_f() function, which seems to be enough as
register is cleared prior CPLD triggers another reset.
But board_early_init_f() is not called from SPL and therefore usage of SPL
can cause reboot loop.
To prevent reboot loop when using SPL, call board_early_init_f() function
in SPL too. For accessing CPLD memory space it is needed to have CPLD entry
in TLB.
With this change it is possible to trigger board reset via CPLD's system
reset register on P2020 RDB board.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.
There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.
Fixes: e8a7f1c32b ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Depending on the boot source, set different CLI prompts. This will help
the user to figure out in which mode the bootloader was started. There
are two special modes: failsafe and SDHC boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During startup the SPL will print where the u-boot proper is read from.
Instead of using the default names, provide more user friendly names.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board is able to boot from the following source:
- user-updateble SPI flash
- write-protected part of the same SPI flash
- eMMC
- SD card
Implement the needed function hooks to support all of these boot
sources.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 6aa4fe3912 ("dm: core: Rename and fix uclass_get_by_name_len()")
changed uclass_get_device_by_name() to an exact match when previously it
behaved as a prefix match.
The roc-cc code relied on this prefix match by only specifying part of
the device name. Fix this by using the full name including the address.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As the Renesas Reduced Pin Count Interface may be locked by TF-A, it is
disabled by default[1]. When unlocked, TF-A passes a DT fragment to
enable it, which is applied to the U-Boot DT[2].
Unlike the memory layout, the RPC-IF enablement is not propagated to
subsequent software. Hence e.g. Linux cannot know if the RPC-IF is
locked or not, and will lock-up when trying to access the RPC-IF when
locked.
Fix this by checking if the RPC-IF is enabled in the TF-A DT fragment, and
setting the status of the RPC-IF device node in the target DT, if
present, to "okay". Do this only when a "flash" subnode is found, to
avoid errors in subsequent software when the RPC-IF is not intended to
be used.
Note that this requires the status of the RPC-IF node to be set to
"disabled" in the target DT, just like in the U-Boot DT.
[1] commit 3d5f45c95c ("ARM: dts: rmobile: Disable RPC HF by
default")
[2] commit 361377dbdb ("ARM: rmobile: Merge prior-stage firmware
DT fragment into U-Boot DT on Gen3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are three different kinds of EEPROM possibly present on boards.
1. 1byte address. For those we should avoid 2byte address in order
not to rewrite the data. Second byte of the address can potentially
be interpreted as the data to write.
2. 2byte address with defined behaviour. When we try to use 1byte
address they just return "FF FF FF FF ... FF"
3. 2byte address with undefined behaviour (for instance, 24LC32AI).
When we try to use 1byte address, then their internal read
pointer is changed to some value. Subsequential reads may be
broken.
To gracefully handle both case #1 and case #3 we read all required
data from EEPROM at once (about 80 bytes). So either all the data is
valid or we fallback to 2byte address.
Cc: Nishanth Menon <nm@ti.com>
Fixes: a58147c2db ("board: ti: common: board_detect: Do 1byte address checks first.")
Reference: https://lore.kernel.org/all/CAJs94Ebdd4foOjhGFu9Bop0v=B1US9neDLxfhgcY23ukgLzFOQ@mail.gmail.com/
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The board code needs this to be set. Otherwise, the recovery mechanism
doesn't work. Therefore, select this option automatically with the
board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Cleanup the included header files in the board code. These are all
leftovers from earlier days.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This is not needed. The user can force setting the variables with
"setenv -f".
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Remove Gerald from maintainer list (email bounced)
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_UBIFS_SILENCE_MSG to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
mbus driver is initialized from arch_cpu_init() callback which is called
before relocation. This driver stores lot of functions and structure
pointers into global variables, so it is data position dependent.
Therefore after relocations all pointers are invalid and driver does not
work anymore as all pointers referes to the old memory, which overlaps with
CONFIG_SYS_LOAD_ADDR and ${loadaddr}.
For example U-Boot fuse command crashes if loadaddr memory is cleared or
rewritten by some image loaded by U-Boot load command.
mw.w ${loadaddr} 0x0 10000
fuse read 0 1 2
Fix this issue by removing of all mbus global variables in which are stored
pointers to structures or functions which changes during relocation. And
replace it by direct function calls (not via pointers). With this change
fuse command finally works.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
When Mox SFP module is connected after Topaz or Peridot module then port DT
node already contains "sfp" label. But Mox SFP module can be connected also
without Topaz or Peridot module in which case it is connected directly into
he eth1 DT node, which is without any label. So add "sfp" label into eth1
DT node in this case.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are already more MCU firmware versions for Turris Omnia in
production, so display git commit (version) of the MCU firmware during
U-Boot startup. It will help to identify what version of MCU firmware is
Turris Omnia using.
MCU firmware for Turris Omnia is open source and available at website:
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl
It can be updated from running system via i2c bus with this tool:
https://gitlab.nic.cz/turris/omnia-mcutool
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
Proper U-Boot removes this direct mapping. So it is available only in SPL.
This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on
32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris
Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform needs to be converted to use DM_ETH as the deadline is 2
years passed due. Disable networking support for now.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As this driver has been converted to DM_ETH and the migration deadline
is 2 years passed, remove the legacy code and callers.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
There is some code here for the legacy non-DM_ETH case, add a guard
around it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have been orphaned for some time and are behind on various
DM migrations. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The *aqds* platforms have not been migrated to be able to enable
CONFIG_DM_ETH with CONFIG_FMAN_ENET. Disable CONFIG_FMAN_ENET on these
platforms.
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
