Commit graph

19124 commits

Author SHA1 Message Date
Javier Martinez Canillas
77eea28074 OMAP3: use a single board file for IGEP devices
Even when the IGEPv2 board and the IGEP Computer-on-Module
are different from a form factor point of view, they are
very similar in the fact that share many components and how
they are wired.

So, it is possible (and better) to have a single board file
for both devices and just use the CONFIG_MACH_TYPE to make
a differentiation between each board when needed.

This change avoids code duplication by removing 298 lines of
code and makes future maintenance easier.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-02-07 10:36:25 -05:00
Rob Herring
5bedf884a8 ARM: highbank: use wfi macro instead of inline asm
Older compilers don't recognize v7 wfi instruction, so use wfi macro to
fix builds on old compilers.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-02-03 14:44:02 +01:00
Rob Herring
2ff467c051 ARM: add wfi assembly macro
Since wfi instruction is only available on ARMv7, add a conditional
macro for it.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-02-03 14:43:58 +01:00
Tetsuyuki Kobayashi
b0404ea126 arm: rmobile: kzm9g: Adjust ETM trace clock
Set ETM TRCLK down to 78MHz to get clear wave form.
This patch makes difference only when you use ETM trace connecting JTAG debugger.

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-02-02 23:45:32 +01:00
Tetsuyuki Kobayashi
f68847fa2f arm: rmobile: kzm9g: Adjust SDRAM setting
After stress test, I found some of kzm9g board occures memory failure.
This patch adust SDRAM setting.
- Enlarge drivability on both SDRAM controller and SDRAM itself
- Raise core voltage

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-02-02 23:45:28 +01:00
Albert ARIBAUD
e5f5c4a977 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-02-02 19:29:59 +01:00
Otavio Salvador
81ca840976 mx23evk: Add initial board support
The following features are supported:
 * 128 MB DDR1 SDRAM
 * DUART
 * SD/MMC Card Socket

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-28 11:51:04 +01:00
Otavio Salvador
38fc15d86c mx23_olinuxino: Add default environment
This adds a default environment with support for MMC booting.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-01-28 11:50:11 +01:00
Marek Vasut
13b1ebdec6 mxs: mmc: mx23_olinuxino: Add MMC support
Add support for the MMC attached to SSP1.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Marek Vasut
e5b380ac68 mxs: mmc: Fix the MMC driver for MX23
The MX23 has different layout of DMA channels. Fix the MMC
driver to support MX23.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Marek Vasut
90bc2bf297 mxs: mmc: Allow overriding default card detect implementation
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Otavio Salvador
8000d8a826 mxs: mmc: Fix MMC reset on iMX23
This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Marek Vasut
f3801e2b9b mxs: ssp: Add SSP registers map for MX23
The MX23 SSP register layout differs from MX28 in certain bits,
adjust the register layout accordingly.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Marek Vasut
0e5c05efb4 mxs: dma: Fix APBH DMA driver for MX23
The MX23 has less channels for the APBH DMA, sligtly different register
layout and some bits in those registers are placed differently. Reflect
this in the driver. This patch fixes MMC/DMA issue on MX23.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:00 +01:00
Troy Kisky
3236921968 mx6qsabrelite: search mii phy address 4-7
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:51 +01:00
Troy Kisky
fe428b909b net: fec_mxc: get phydev before fec_probe
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:51 +01:00
Troy Kisky
4dc27eed52 net: fec_mxc: only call phy_connect in fec_probe
This allows us to create the phydev before calling
fec_probe in later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
ef8e3a3bbf net: fec_mxc: use fec_set_dev_name to set name
This allows us to create the phydev before calling
fec_probe in later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
1adb406b01 phy: add phy_find_by_mask/phy_connect_dev
It is useful to be able to try a range of
possible phy addresses to connect.

Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
eef2448039 net: fec_mxc: have fecmxc_initialize call fecmxc_initialize_multi
Having only one call to fec_probe will ease the changing of its
parameters.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
575c5cc06f net: fec_mxc: change fec_mii_setspeed parameter
Only the hardware ethernet registers are needed
for this function, so don't pass the more general
structure. I'm trying to separate MII and fec.

This also fixes MX28 fec_mii_setspeed use on secondary ethernet port

This was found by inspection of the code and should be
checked on real hardware.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
09439c3197 net: fec_mxc: delete CONFIG_FEC_MXC_MULTI
It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
c30eab2ddd doc/README.fec_mxc: add documentation
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:49 +01:00
Fabio Estevam
f093088214 mxs: Use __weak annotation to simplify code
Using the __weak annotation can make the code cleaner.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2013-01-28 06:54:19 +01:00
Fabio Estevam
6e08385715 tools: imximage: Let .name field be more generic
Since this structure is not i.MX5x specific, remove the '5x' to make it more
generic.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-28 06:49:51 +01:00
Fabio Estevam
e4f8d96423 mx6qsabre_common: Let mmc partition be board specific
commit 49ea0ff5 (49ea0ff5) introduced CONFIG_SYS_MMC_ENV_PART into mx6qsabresd.h
to store the mmc partition, but in order for it to have effect we should place
it into 'mmcpart' variable.

Also add CONFIG_SYS_MMC_ENV_PART into mx6qsabreauto.h.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-28 06:45:18 +01:00
Knut Wohlrab
73448b1f80 mx6qsabreauto: enable USB host interface
The USB host interface is routed to plug USB1/J30 on the mother board.

Signed-off-by: Knut Wohlrab <knut.wohlrab@de.bosch.com>
2013-01-28 06:43:58 +01:00
Marek Vasut
8303ed128a mxs: Boost the memory power supply
The memory power supply on MX23 didn't pump out enough juice into
the DRAM chip, thus caused occasional memory corruption. Fix this.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-01-28 06:40:38 +01:00
Troy Kisky
71a988aa63 imximage.cfg: run files through C preprocessor
The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.

The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile

.gitignore was updated to ignore .cfgtmp files.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-22 10:20:13 +01:00
Otavio Salvador
0023997709 mxs: Add MX23 quirks into the clock code
The MX23 has different handling of the SSP clock and GPMI NAND clock sources,
add necessary quirks into the clock code to properly handle these.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:22 +01:00
Fabio Estevam
4750953ed9 woodburn: Set Write Protection GPIO as input
Set Write Protection GPIO as input.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-01-21 12:05:22 +01:00
Marek Vasut
64a9386080 mxs: Add MX23 olinuxino board support
This patch adds support for MX23-based Olinuxino board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:22 +01:00
Marek Vasut
9fb6aa9a61 mxs: Linux uses ttyAMA0 as DUART
Replace use of ttyAM0 with ttyAMA0 as default serial console.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:22 +01:00
Otavio Salvador
30af6c0bca mxs: Fix the memory init for MX23
The memory init is slightly different on MX23, thus split the memory
init for mx23 and mx28 into different functions.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:22 +01:00
Marek Vasut
7788bf067d mxs: Add function to ungate the power block on MX23
The power block on MX23 must first be ungated before it can be operated.
Add function to MXS power init that ungates it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:22 +01:00
Marek Vasut
1a3c5ffe4f mmc: Limit the number of used SSP ports on MX23
The MX23 can only use two SSP ports.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Otavio Salvador
deb0757cc7 mx23: config: Enable mxsboot tool for i.MX23 based boards
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Otavio Salvador
e6d93c26c7 mx23: config: Enable building of u-boot.sb binary
For i.MX23 we need to pass imx23 as elftosb param.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Otavio Salvador
1ddf386e23 mx23: SPL: Initialize DDR at 133MHz
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Otavio Salvador
f942f7d962 mx23: SPL: Add boot mode support
This adds the boot mode support for i.MX23 processors.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Otavio Salvador
a8b2884d94 mx23: Add boot mode description
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Otavio Salvador
f69077e420 mx23: Add support on print_cpuinfo()
Add information to identify i.MX23 chips and its known revisions.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:20 +01:00
Marek Vasut
95e873d601 mx23: ssp: Fix ssp-regs.h for MX23
Disable SSP2 and SSP3 ports on MX23.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:20 +01:00
Marek Vasut
06dc8160a0 mx23: Add POWER and CLKCTRL register definitions
Add register definitions for the i.MX23 power control block and
clock control block. These are essential for the basic bootstrap
of the i.MX23. Also, properly include them in imx-regs.h .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:20 +01:00
Otavio Salvador
180f47a8df mx23: Add iomux-mx23.h
This has been copied from Linux source at revision 786f02b719f.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:20 +01:00
Otavio Salvador
3fd7f365e1 mx23: Add register base addresses
This adds the base addresses of i.MX23 and easy the detection of wrong
order in board setup, in case no SoC has been set, an error is raised
during build.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:20 +01:00
Otavio Salvador
bf48fcb61b mxs: clock: Use 'mxs' prefix for methods
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:20 +01:00
Marek Vasut
14e26bcfa7 mxs: ssp: Pull out the SSP bus to regs conversion
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:19 +01:00
Marek Vasut
59b6defa2b mxs: mmc: Drop unused members from struct mxsmmc_priv
The clock data are not used by the driver, drop them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:19 +01:00
Allen Martin
7cb70a34b9 fdt: fix dts preprocessor options
Using "-ansi" preprocessor option will cause dts lines that begin with
'#' to choke the preprocessor.  Change to "-x assembler-with-cpp"
instead which is what the kernel uses to preprocess dts files.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-01-17 09:07:59 -07:00