Add the specific board model from EEPROM config to the device-tree to
make it easier to access from Linux userspace.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
remove unused SPL features to shink the size of the SPL which
otherwise would no longer fit into IMX8M Mini OCRAM.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add PCIe reset gpio to the Bx50v3 devicetree and get get rid of
CONFIG_PCIE_IMX_PERST_GPIO.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Select CONFIG_IMX_HAB so that the "hab_status" command
becomes available, which is useful for checking if the
chip has been correctly setup to run in secure boot mode.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Do the following to add support for it:
- add dts
- add PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add board model/serial# strings to env. Move the creation of the strings
to gsc_read() and the display of the info into gsc_info() so they are
available to U-Boot proper.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
replace looking up i2c bus name by bus number and define bus numbers and
eeprom address with #defines.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The intention of commit d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT
with CONFIG_IMX_HAB") was to convert from CONFIG_SECURE_BOOT to
CONFIG_IMX_HAB, but it replaced with an extra "_" character.
Fix it by using the correct CONFIG_IMX_HAB symbol.
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The GW54xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW53xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5913 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- Digital I/O connector (I2C/GPIO/UART)
- u-blox Zoe-M8Q GPS
- 1x RJ45 GbE
- 1x MiniPCIe socket with PCIe USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5912 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- CAN/RS485 connector
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- 1x FEC GbE RJ45 with 802.3at Active PoE
- 1x PCI GbE RJ45 with Passive PoE
- 5x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with PCIe/USB 2.0 and SIM socket
- Aux power input with wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5910 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- TI CC1352 ARM Cortex-M4 multiprotocol sub-1GHz / 2.4GHz wireless MCU
- On-board brcmfmac WiFi and BT module
- RGMII RJ45 GbE
- 1x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.
U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.
Fixes 72c46327f0: ("imx: ventana: enable dm support for USB")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Move board/revision specific dt fixups for WDOG and UHS-I features
so that we can call them early for U-Boot control dt as well.
Additionally drop a deprected non-mainline dt-prop fixup regarding
HDMI input format.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
EEPROM bits no longer indicate support for NAND so instead use
hard-coded value from board config struct.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Only one dtb is currently supported, so match with imx6-colibri.
Signed-off-by: Ming Liu <ming.liu@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Update the documentation on how to build the u-boot image for
Colibri iMX8QXP, adding support of V1.0D revision of the module.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
If config block support is enabled, USB gadget modes unconditionally
use Toradex Product ID as USB PID. Some applications might prefer a
different and/or static USB PID. Add a Kconfig configuration option
to descide whether to use USB PID from config block or the fallback
config option CONFIG_G_DNL_PRODUCT_NUM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Do not pass the console baudrate to the 'console' variable
to avoid the baudrate being passed twice when extlinux.conf
contains the standard: console=${console},${baudrate} format.
cat /proc/cmdline
root=PARTUUID=00000000-01 rootwait rw console=ttymxc0,115200,115200
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import the imx28-evk devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx28evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Modified the help text of 'chpart' command ,mentioning that it is
for MTD devices.
Signed-off-by: Adarsh Babu Kalepalli <opensource.kab@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
HELP description is provided for ‘configure’ sub-command
of ‘blkcache’.
Signed-off-by: Adarsh Babu Kalepalli <opensource.kab@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Symbol CONFIG_SYS_ID_EEPROM is defined in include/configs/MPC8548CDS.h
but never used. Remove it here and from the whitelist.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Start out by documenting general expectations on when CI is run, how
anyone can run Azure pipelines, and how GitLab CI pipelines can be run.
Signed-off-by: Tom Rini <trini@konsulko.com>
In SquashFS, the contents of a directory is stored by
squashfs_directory_entry structures which contain the file's name, inode
and position within the filesystem.
The inode number is not stored directly; instead each directory has one
or more headers which set a base inode number, and files store the
offset from that to the file's inode number.
In mksquashfs, each inode is allocated a number in the same order as
they are written to the directory table; thus the offset from the
header's base inode number to the file's inode number is usually
positive.
Hardlinks are simply stored with two directory entries referencing the
same file. This means the second entry will thus have an inode number
much lower than the surrounding files. Since the header's base inode
number comes from the first entry that uses the header, this delta will
usually be negative.
Previously, U-Boot's squashfs_directory_entry.inode_offset field was
declared as an unsigned value. Thus when a negative value was found, it
would either resolve to an invalid inode number or to that of an
unrelated file.
A squashfs image to test this can be created like so:
echo hi > sqfs_test_files/001-root-file
mkdir sqfs_test_files/002-subdir
touch sqfs_test_files/002-subdir/003-file
ln sqfs_test_files/{001-root-file,002-subdir/004-link}
mksquashfs sqfs_test_files/ test.sqfs -noappend
Note that squashfs sorts the files ASCIIbetacally, so we can use the
names to control the order they appear in. The ordering is important -
the first reference to the file must have a lower inode number than the
directory in which the second reference resides, and the second
reference cannot be the first file in the directory.
Listing this sample image in U-Boot results in:
=> sqfsls virtio 2 002-subdir
0 003-file
Inode not found.
0 004-link
Signed-off-by: Campbell Suter <campbell@snapit.group>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The "-E" option to mkimage generates a FIT with external data using the
data-size and data-offset properties which must both be ignored when
verifying a signature.
Add "data-offset" to the list of excluded properties for signature
verification; since the line is now too long, re-format the list to
one-per-line and make it static since the data is constant.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current stable release of LLVM is 12, update to that. While at it,
fix that we had not correctly upgraded to LLVM 11 previously.
Signed-off-by: Tom Rini <trini@konsulko.com>
