Commit graph

7688 commits

Author SHA1 Message Date
Tom Rini
768f6096f9 Merge git://git.denx.de/u-boot-arc 2015-01-20 16:41:11 -05:00
Sinan Akman
b9315890f6 MAINTAINERS: add me as the maintainer of mpc837xerdb
Signed-off-by: Sinan Akman <sinan@writeme.com>
Cc: Tom Rini <trini@ti.com>
2015-01-20 10:19:57 -05:00
Simon Glass
22d69fd7a8 imx: ls102xa: Remove reference to gdata
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-20 10:15:46 -05:00
Simon Glass
10e3d7ecd3 imx: woodburn: Remove reference to gdata
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-01-20 10:15:33 -05:00
Simon Glass
57241b1d72 imx: cm_fx6: Remove reference to gdata
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2015-01-20 10:15:28 -05:00
Tom Rini
ab77f24119 Merge branch 'master' of git://git.denx.de/u-boot-ti 2015-01-16 10:25:01 -05:00
Masahiro Yamada
d928664f41 powerpc: 74xx_7xx: remove 74xx_7xx cpu support
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2

Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
2015-01-16 10:24:39 -05:00
Alexey Brodkin
e20bcb046b board/synopsys: remove selection of CPU from the board
Both ARCangel4 and AXS10x are FPGA-based boards so they may have
different CPUs. For now we have only 1 option (ARC700) and we define
this as default in arch Kconfig.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-01-15 22:40:49 +03:00
Evgeni Dobrev
9637c4b2dd Add support for Seagate BlackArmor NAS220
Add support for Seagate BlackArmor NAS220

Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
2015-01-14 11:37:39 -05:00
Hans de Goede
4458b7a6e1 sunxi: usbc: Add support for usb0 to the common usbc code
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Chen-Yu Tsai
507e27dfc9 sunxi: video: Add support for external DAC enable pin
The external DAC for VGA output might have either a power or reset
control pin that needs to be pulled up, as is the case on the
Hummingbird A31.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:40 +01:00
Chen-Yu Tsai
2583d5b192 sunxi: video: Allow external DACs for VGA on platforms without TV encoders
Using an external DAC for VGA output was available on sun5i. Since
some other SoCs don't have a builtin TV encoder, but might have
use for a VGA output, enable the option for the platforms that
don't have TV encoders.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:40 +01:00
Hans de Goede
213480e12d sunxi: video: Add lvds support
Add support for lvds lcd panels

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14 14:56:40 +01:00
Zoltan HERPAI
213dcbfdeb sunxi: add Linksprite pcDuino v1/v2 support
Add support for a sun4i board built by Linksprite. This addition covers
both v1 and v2 versions. As the board has been working with 408MHz memory
setting in the u-boot-sunxi branch, and has been proven to be running stable
during my tests as well, a respective new DRAM config file is added as well.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:39 +01:00
Hans de Goede
d9786d2380 sunxi: video: Add VGA output support
Add support for VGA directly from the sunxi SoC / display engine.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
e2bbdfb1e3 sunxi: video: Add support for VGA via external DACs connected to the LCD pins
Add support for external DACs connected to the parallel LCD interface driving
a VGA connector, such as found on the Olimex A13 boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
2fbf091a54 sunxi: video: Enable video on sun8i, which supports LCD but not HDMI
The A23 (sun8i) only has lcd output support, so allow building the video code
without HDMI support for use with the A23.

Also the A23 has the same reset bits (and necessity to enable the DRC block)
as the sun6i, so enable those bits for sun8i too.

Note building without HDMI support is useful for the A13 (sun5i variant) too,
as that one does not have HDMI either.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
2dae800f1e sunxi: video: Add lcd output support
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:39 +01:00
Hans de Goede
81ec100151 sun7i: Add new Bananapro board / defconfig
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Siarhei Siamashka
f4f0df09b9 sun7i: Add defconfig for MSI Primo73 tablet
This patch uses the same DRAM settings as in the pre-installed
Android firmware. The LCD display is supported too.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:37 +01:00
Siarhei Siamashka
80e8669f6e sun6i: Add defconfig for MSI Primo81 tablet
This patch uses the same ZQ and DRAM clock settings as in the
pre-installed Android firmware.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:37 +01:00
Siarhei Siamashka
f0ce28e9ed sunxi: Fix CONFIG_UART0_PORT_F build and add it to menuconfig
The CONFIG_UART0_PORT_F option has been supported since
    http://git.denx.de/?p=u-boot.git;a=commit;h=ff2b47f6a9cc1025

This option is primarily useful only for low level u-boot debugging
on tablets, where normal UART0 is difficult to access and requires
device disassembly and/or soldering.

This patch now allows it to be selected from menuconfig. A dependency on
SPL_FEL is added because u-boot does not support booting from NAND yet
and also booting from SD card is impossible when a MicroSD breakout board
is plugged into the SD slot.

Additionally a compilation problem is fixed:

common/spl/built-in.o: In function `spl_mmc_load_image':
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:94: undefined reference to `mmc_initialize'
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:96: undefined reference to `find_mmc_device'
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:104: undefined reference to `mmc_init'
scripts/Makefile.spl:206: recipe for target 'spl/u-boot-spl' failed

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:37 +01:00
Hans de Goede
1d7cd7bf7d sun8i: Add defconfig for Ippo_q8h v1.2
We need separate defconfigs for the v5 and v1.2 versions of this board, as
they use different DRAM parameters.

Note they also use different dtb files, as the wifi is different too.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
08fd1479c7 sun8i: Add dram initialization support
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
d3a96f7a68 sunxi: axp221: Disable dcdc4 on sun8i (A23)
dcdc4 is not used on sun8i, disable it.

While at it also add comments to the other fixed voltages to document what
they are used for.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
50e0d5e60b sunxi: axp221: Explicitly turn off unused voltages
Explicitly turn off unused voltages, rather then leaving them as is. Likewise
explictly enabled the dcdc convertors, rather then assuming they are already
enabled at boot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
1262a85fe3 sunxi: axp221: Make dcdc1 voltage configurable
The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like
GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to
safe battery, but not on all, make it configurable so that we can use the
same settings as the original firmware on all boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Chen-Yu Tsai
a805b7e5da sun6i: Add new board Merrii Hummingbird A31
The Merrii Hummingbird A31 is a A31 based development board with 1G
RAM, 8G NAND, AP6210 WiFi+BT, gigabit ethernet, USB OTG, 2 USB 2.0
ports connected to a USB hub chip, HDMI, VGA, TV and stereo in/out.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:36 +01:00
Hans de Goede
cac5b1cc0d sunxi: Add sunxi_get_sid helper function
On sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a helper function to abstract this away.

This makes our MAC address generation code also work on sun6i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
b0f25b6f51 sun6i: Add new CSQ_CS908 board
The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out:

http://www.geekbuying.com/item/CS908-Allwinner-A31S-Quad-Core-1-2GHz-Android-4-4-Mini-TV-Box-HDMI-HDD-Player-1G-8G-WIFI-Miracast---Black-333395.html

Note it has no sdcard slot and therefore can only be fel booted.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
37781a1a7e sun6i: Make dram clk and zq value Kconfig options
It turns out that there is a too large spread between boards to handle this
with a default value, turn this into Kconfig options, and set the values
the factory images are using for the Colombus and Mele_M9 boards.

Note this changes the ZQ default when not overriden through defconfig from
120 to 123, as that is what most boards seem to actually use.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Anthoine Bourgeois
a91ef4adfb arm: omap3: devkit8000: inherit from ti_omap3_common.h
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
2015-01-13 15:26:11 -05:00
Felipe Balbi
403d70abd9 board: ti: am43xx: add support for AM43xx Industrial Development Kit
AM43xx Industrial Development Kit is a new board
based on AM437x line of SoCs. Targetted at Industrial
Automation applications, it comes with EtherCAT, motor
control and other goodies.

Thanks to James Doublesin for all the help.

Cc: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13 15:26:10 -05:00
Tom Rini
5f88ed5cde Merge git://git.denx.de/u-boot-x86 2015-01-13 13:39:25 -05:00
Felipe Balbi
d5c082a32d board: ti: am43xx: take care of all OPPs
Make sure that all OPPs are checked on
scale_vcores(). While at that also fix 600MHz
VDD_MPU voltage according to AM437x Data Manual
available at [1].

Table 5-3 on that document, lists all valid
voltages per frequency.

[1] http://www.ti.com/lit/ds/symlink/am4379.pdf

Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13 11:53:40 -05:00
Felipe Balbi
068ea0a8a8 board: ti: am43xx: replace if else if else with a switch
A switch statement fits better in this case,
specially considering we have a few extra
frequencies to use.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13 11:53:39 -05:00
James Doublesin
c87b6a96ac arm: am437x: Correct PLL frequency for 25MHz
The frequencies for 25MHz in dpll_per were out of spec for 25MHz,
correct.

Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13 11:53:39 -05:00
James Doublesin
fc46bae2ae arm: am437x: Enable hardware leveling for EMIF
Switch to using hardware leveling for certain parameters on the EMIF
rather than using precalculated values.  Doing this also means we have a
common place now between am437x and am335x for setting
emif_sdram_ref_ctrl with a value for the correct delay length.

Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13 11:53:39 -05:00
James Doublesin
e2a6207bcc arm: am437x: PLL values for all input frequencies
Need to provide PLL values for all possible input frequencies (19.2, 24,
25, 26MHz). Values provide are also optimized for jitter (needed
especially for PER PLL and DDR PLL).

Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-01-13 11:53:39 -05:00
Bin Meng
48a223e4ba x86: coreboot: Wrap cros_ec initialization
cros_ec_board_init() should be called only when CONFIG_CROS_EC is
enabled.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:04 -08:00
Bin Meng
ade8127a79 x86: Make chromebook_link the default board for coreboot
Change SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE to chromebook_link
which is currently the only real board officially supported to run
U-Boot loaded by coreboot.

Note the symbolic link file chromebook_link.dts is deleted and
link.dts is renamed to chromebook_link.dts.

To avoid multiple definition of video_hw_init, the CONFIG_VIDEO_X86
define needs to be moved to arch/x86/cpu/ivybridge/Kconfig.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:04 -08:00
Bin Meng
fa48e51013 x86: Remove include/configs/coreboot.h
Since we already swtiched to use the new mechanism for building
U-Boot for coreboot, coreboot.h is no longer needed so remove it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:04 -08:00
Bin Meng
24ef04280c x86: Move CONFIG_SYS_CAR_xxx to Kconfig
Move CONFIG_SYS_CAR_ADDR and CONFIG_SYS_CAR_SIZE to Kconfig so that
we don't need them in the board configuration file thus the same
board configuratoin file can be used to build both coreboot version
and bare version.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:04 -08:00
Bin Meng
c57522f656 x86: coreboot: Make SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE configurable
In theory U-Boot built for coreboot is supposed to run as a payload
to be loaded by coreboot on every board that coreboot supports.
The U-Boot build process uses SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE
which are hardcoded in board defconfig and Kconfig files. For better
support of coreboot, we want to make these two options configurable
so that we can easily change them during 'make menuconfig' so that
the generated U-Boot image for coreboot is board configuration aware.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:03 -08:00
Bin Meng
8cb20ccc34 x86: Move CONFIG_X86_RESET_VECTOR and CONFIG_SYS_X86_START16 to Kconfig
Convert CONFIG_X86_RESET_VECTOR and CONFIG_SYS_X86_START16 to Kconfig
options so that we can remove them from board configuration file.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-13 07:25:03 -08:00
Matthias Fuchs
7eaeb08b20 ppc4xx: cleanup CPCI4052 board
- remove some obsolete code
- switch to generic board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2015-01-13 09:37:26 -05:00
Matthias Fuchs
5f1459dc0d ppc4xx: remove some CPCI405 variants
only keep CPCI4052

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2015-01-13 09:37:25 -05:00
Matthias Fuchs
5f8f6294a7 ppc4xx: remove G2000 board
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2015-01-13 09:37:25 -05:00
Matthias Fuchs
fc88a5bf79 ppc4xx: remove WUH405 board
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2015-01-13 09:37:25 -05:00
Matthias Fuchs
807db88b62 ppc4xx: remove VOH405 board
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2015-01-13 09:37:25 -05:00