Add documention for Rockchip rkmtd virtual block device.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xunlong Orange Pi 5 Plus is a single-board computer based on the
Rockchip RK3588 SoC. The board provides abundant interfaces, including
two HDMI output ports, one HDMI input port, two 2.5G Ethernet ports,
M.2 M-Key slot, M.2 E-Key slot, two USB 3.0, two USB 2.0, and two Type-C.
Features tested on a Orange Pi 5 Plus 4GB v1.2:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Xunlong Orange Pi 5 is a single-board computer based on the Rockchip
RK3588S SoC. The board provides abundant interfaces, HDMI output, GPIO
interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0,
etc.
Features tested on a Orange Pi 5 4GB v1.2:
- SD-card boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPC-T6 is a Rockchip RK3588 based SBC by FriendlyElec.
There are four variants depending on the DRAM size: 4G/32GB eMMC,
8G/64GB eMMC, 16G/16MB SPI NOR, and 16G/256GB eMMC/16MB SPI NOR
Specifications:
CPU: Rockchip RK3588, 4x Cortex-A76 (up to 2.4GHz)
+ 4x Cortex-A55 (up to 1.8GHz)
GPU: Mali-G610 MP4
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder,
4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
eMMC: 0GB/32GB/64GB/256GB HS400
MicroSD Slot: MicroSD SDR104
PCIe 3.0: M.2 M-Key x1, PCIe 3.0 x4 for NVMe SSDs up to 2,500 MB/s
Ethernet: PCIe 2.5G 2x Ethernet (RTL8125BG)
PCIe 2.1: M.2 E-Key x1, PCIe 2.1 x1 and USB2.0 Host,
supports M.2 WiFi and Bluetooth
4G Module: MiniPCIe x1, MicroSIM Card Slot x1
Audio Out: 3.5mm jack for stereo headphone output
Audio In: 2.0mm PH-2A connector for analog microphone input
Video Input: standard HDMI input port, up to 4Kp60
2x 4-lane MIPI-CSI, compatible with MIPI V1.2
Video Output: 2x standard HDMI output ports compatible with HDMI2.1,
HDMI2.0, and HDMI1.4
2x 4-lane MIPI-DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
USB-A: USB 3.0, Type A
USB-C: Full function USB Type‑C port, DP display up to 4Kp60, USB 3.0
40-pin 2.54mm header connector: up to 2x SPIs, 6x UARTs, 1x I2Cs,
8x PWMs, 2x I2Ss, 28x GPIOs
Debug UART: 3 Pin 2.54mm header, 3V level, 1500000bps
Onboard IR receiver: 38KHz carrier frequency
RTC Battery: 2 Pin 1.27/1.25mm RTC battery connector for low power
RTC IC HYM8563TS
5V Fan connector
Working Temperature: 0C to 70C
Power: 5.5*2.1mm DC Jack, 12VDC input
Dimensions: 110x80x1.6mm (without case) / 86x114.5x30mm (with case)
Kernel commits:
893c17716d0c ("arm64: dts: rockchip: Add NanoPC T6")
a721e28dfad2 ("arm64: dts: rockchip: Add NanoPC T6 PCIe Ethernet support")
ac76b786cc37 ("arm64: dts: rockchip: Add NanoPC T6 PCIe e-key support")
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When built with CONFIG_IMX_HAB, the full FIT image, including stuff
tacked on beyond the end of the fdt structure, is expected to be (fdt
size rounded up to 0x1000 boundary)+CONFIG_CSF_SIZE.
Now, when the FIT image is loaded from a storage device, it doesn't
really matter that the flash.bin that gets written to target isn't
quite that big - we will just load some garbage bytes that are never
read or used for anything. But when flash.bin is uploaded via uuu,
it's important that we actually serve at least as many bytes as the
target expects, or we will hang in rom_api_download_image().
Extend the logic in the csf.sh script so that the csf blob is padded
to CONFIG_CSF_SIZE minus the size of the IVT header.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The SPL authenticates image starting from CONFIG_SPL_LOAD_FIT_ADDRESS
address, update the csf_fit.txt to match.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add documentation to explain the printing of the capsule headers
through the mkeficapsule tool.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* Bump urllib3 version
* Migrate Renesas board docs to rst
* Link an introduction video
UEFI
* Use same GUID as EDK II for auto-created boot options
* Clean up BitBlt test
-----BEGIN PGP SIGNATURE-----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=vtF1
-----END PGP SIGNATURE-----
Merge tag 'efi-2024-01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-01-rc1
Documentation:
* Bump urllib3 version
* Migrate Renesas board docs to rst
* Link an introduction video
UEFI
* Use same GUID as EDK II for auto-created boot options
* Clean up BitBlt test
Some of the information in README.rmobile is obsolete, references
defconfigs which no longer exist in u-boot or has broken links. The
information which is still relevant is moved into the reStructuredText
documentation under `doc/board/renesas`, and `doc/README.rmobile` is
dropped.
The list of boards in `doc/board/renesas` is converted into a table so
it's easier to see which defconfig to use. The list is expanded based on
reviewing the current u-boot code and the contents of the eLinux wiki
[1] [2].
[1]: https://elinux.org/R-Car
[2]: https://elinux.org/RZ-G
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This video covers the basics in a short time, so add a link to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Cyclic now just print a warning once instead of disabling the cyclic
function when the cyclic function upon exceeding CPU time usage.
Fixes: ddc8d36a74 ("cyclic: Don't disable cylic function upon exceeding CPU time")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Rephrase the paragraph.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
While not a direct issue for us, urllib3 before 1.26.17 is vulnerable to
CVE-2023-43804 to bump our version up.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use urllib3 2.0.6
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
There is a function for this but it is never used. Showing the history is
a useful feature, so add a new 'history' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is part of a longer series, which isn't quite ready. Revert this
for now at least.
This reverts commit 4cb6c8e5f0.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add 'Integration with IDEs' chapter.
For now, this chapter is mostly a reference to the documentation of
gen_compile_commands, in doc/build, but it can be futurely used as
a guide for other IDE-friendly features.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
This documentation briefly explains what is a compilation database,
and how to use the script to generate one.
This is not a portage, as there was no original documentation in the
Linux sources.
Acknowledge the documentation in the script's header and in doc/build
index.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
The man page correctly said that -B was ignored without -E, while the
`mkimage -h` output suggested otherwise. Now that -B can actually be
used by itself, update the man page.
While at it, also amend the `mkimage -h` line to mention the
connection with -E.
The FDT header is a fixed 40 bytes, so its size cannot (and is not)
modified, while its alignment is a property of the address in RAM one
loads the FIT to, so not something mkimage can affect in any way. (In
the file itself, the header is of course at offset 0, which has all
possible alignments already.)
Reported-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Moving towards using .dtso for overlay sources, update the
documentation examples to follow that pattern.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added new xenguest_arm64_virtio_defconfig which
enables support for virtio-blk using various types
of transport like virtio-pci, vrtio-mmio. Currently
supported: up to 2 PCI host bridges and 10 MMIO devices.
Note: DT parsing code was partly taken from pci-uclass.c
Limitation: All memory regions should be
below 4GB address space.
Signed-off-by: Andrii Chepurnyi <andrii_chepurnyi@epam.com>
Make it possible for data that was externalized using a static external
position (-p) to be internalized. Enables the ability to convert
existing FIT images built with -p to be converted to a FIT image where the
data is internal, to be converted to a FIT image where the data is
external relative to the end of the FIT (-E) or change the initial
static external position to a different static external position (-p).
Removing the original external-data-related properties ensures that
they're not present after conversion. Without this, they would still be
present in the resulting FIT even if the FIT has been, for example,
internalized.
Signed-off-by: Lars Feyaerts <lars@bitbiz.be>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Update and improve documentation about build steps for SoCs that
require using TF-A and TPL binaries provided by Rockchip, such as
rk3308. Add rk3308 boards case to rST document. Add ROCK Pi S in
the list of supported boards. Minor page format improvements.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move this down by 4KB so that it is large enough to hold the devicetree.
Also fix up the devicetree address in the documetation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the useful help to Kconfig.
Drop mention of CONFIG_SYS_MALLOC_SIMPLE since it doesn't exist.
Correct a 'CONFIGSYS_MALLOC_F_LEN' typo
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <sjg@chromium.org>
`part` option is in hexadecimal, so information is missing in usage
documentation.
Callgraph for `part` parsing is :
do_load -> fs_set_blk_dev -> part_get_info_by_dev_and_name_or_num ->
blk_get_device_part_str -> hextoul (This is why it is hexadecimal)
Signed-off-by: Mickaël Tansorier <mickael.tansorier@smile.fr>
Reviewed-by: Yoann Congal <yoann.congal@smile.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
A '.update' extension does not get preserved by buildman, so change it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Walle <michael@walle.cc>
The output from "dm tree" or "dm uclass" is a bit annoying
if the number of devices available on the system is huge.
(This is especially true on sandbox when I debug some DM code.)
With this patch, we can specify the uclass name or the device
name that we are interested in in order to limit the output.
For instance,
=> dm uclass usb
uclass 121: usb
0 usb@1 @ 0bcff8b0, seq 1
uclass 124: usb
=> dm tree usb:usb@1
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ ] usb_sandbox usb@1
usb_hub 0 [ ] usb_hub `-- hub
usb_emul 0 [ ] usb_sandbox_hub `-- hub-emul
usb_emul 1 [ ] usb_sandbox_flash |-- flash-stick@0
usb_emul 2 [ ] usb_sandbox_flash |-- flash-stick@1
usb_emul 3 [ ] usb_sandbox_flash |-- flash-stick@2
usb_emul 4 [ ] usb_sandbox_keyb `-- keyb@3
If you want forward-matching against a uclass or udevice name,
you can specify "-e" option.
=> dm uclass -e usb
uclass 15: usb_emul
0 hub-emul @ 0bcffb00, seq 0
1 flash-stick@0 @ 0bcffc30, seq 1
2 flash-stick@1 @ 0bcffdc0, seq 2
3 flash-stick@2 @ 0bcfff50, seq 3
4 keyb@3 @ 0bd000e0, seq 4
uclass 64: usb_mass_storage
uclass 121: usb
0 usb@1 @ 0bcff8b0, seq 1
uclass 122: usb_dev_generic
uclass 123: usb_hub
0 hub @ 0bcff9b0, seq 0
uclass 124: usb
=> dm tree -e usb
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ ] usb_sandbox usb@1
usb_hub 0 [ ] usb_hub `-- hub
usb_emul 0 [ ] usb_sandbox_hub `-- hub-emul
usb_emul 1 [ ] usb_sandbox_flash |-- flash-stick@0
usb_emul 2 [ ] usb_sandbox_flash |-- flash-stick@1
usb_emul 3 [ ] usb_sandbox_flash |-- flash-stick@2
usb_emul 4 [ ] usb_sandbox_keyb `-- keyb@3
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a little more detail as to why coreboot64 is preferred for booting
Linux distros.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move this out of the main file since for simple users it is easier to
rely on standard boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Refresh the summary information so it is more up-to-date. Add links to
the coreboot and slimbootloader docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is enough material that it makes sense to split this up into
several files. Create an x86/ directory for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is very annoying as it is quite slow on many machines. Also, U-Boot
has an existing 'preboot' mechanism to enable this feature if desired.
Drop this code so that it is possible to choose whether to init USB or
not.
Use the existing USE_PREBOOT mechanism instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable bootstd options and provide instructions on how to boot a linux
distro using coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add these options to permit access to more disk types.
Add some documentation as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a note about using -cdrom with QEMU.
Suggested-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
When building in a portage chroot, we do not have the environment needed
to build pylibfdt. It is instead build as a separate package.
Provide a build option to tell U-Boot to skip this part of the build. We
still need it to use binman, etc. but don't need it to build its
dependencies.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mike Frysinger <vapier@chromium.org>
[s/build bytes/builds bytes in tools.rst]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
clk:
- Dont return error when assigned-clocks is empty or missing
dm:
- Support reading a single indexed u64 value
- Add support for reading bootscript address/flash address from DT
cmd:
- Fix flash_is_unlocked API
fpga:
- Define fpga_load() for debug build
global:
- U-Boot project name cleanup (next2)
net:
- zynq_gem: Use generic_phy_valid() helper
- axienet: Convert to ofnode functions
- gmii2rgmii: Read bridge address from DT
pytest:
- skip tpm2_startup when env__tpm_device_test_skip=True
spi-nor:
- Add mx25u25635f support
- zynqmp_qspi: Tune cache behavior
trace:
- Fix flyrecord alignment issue
xilinx:
- Move scriptaddr to DT as bootscr-address
- Pick script_offset_f/script_size_f from DT as bootscr-flash-offset/size
- Do not generate distro boot variables if disabled
versal:
- Extend memory ranges to cover HBM
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
- Clean mini targets bootcommand
- Fix clock driver
versal-net:
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
zynqmp;
- Allow AES to run from SPL
- Enable CMD_KASLRSEED
- Add proper dependencies for USB and remove ZYNQMP_USB
- Fix user si570 default frequency for zcu* boards
- Cover SOM rev2 revision
- Various DT changes
- Add firmware and pinctrl support for tristate configuration
(high impedance/output enable)
- Add output-enable pins to SOMs
- Fix distroboot prioritization in connection to available devices
- Read bootscript address/flash address from DT
- Fix pcap_prog address
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZQwqWAAKCRDKSWXLKUoM
IQYIAJ9WQrnZoCfi7MuxzYA2t34Dbx4gkwCgk1o6bX+R89jvjBOhgZOlXTQCbb0=
=/rxs
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2024.01-rc1
clk:
- Dont return error when assigned-clocks is empty or missing
dm:
- Support reading a single indexed u64 value
- Add support for reading bootscript address/flash address from DT
cmd:
- Fix flash_is_unlocked API
fpga:
- Define fpga_load() for debug build
global:
- U-Boot project name cleanup (next2)
net:
- zynq_gem: Use generic_phy_valid() helper
- axienet: Convert to ofnode functions
- gmii2rgmii: Read bridge address from DT
pytest:
- skip tpm2_startup when env__tpm_device_test_skip=True
spi-nor:
- Add mx25u25635f support
- zynqmp_qspi: Tune cache behavior
trace:
- Fix flyrecord alignment issue
xilinx:
- Move scriptaddr to DT as bootscr-address
- Pick script_offset_f/script_size_f from DT as bootscr-flash-offset/size
- Do not generate distro boot variables if disabled
versal:
- Extend memory ranges to cover HBM
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
- Clean mini targets bootcommand
- Fix clock driver
versal-net:
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
zynqmp;
- Allow AES to run from SPL
- Enable CMD_KASLRSEED
- Add proper dependencies for USB and remove ZYNQMP_USB
- Fix user si570 default frequency for zcu* boards
- Cover SOM rev2 revision
- Various DT changes
- Add firmware and pinctrl support for tristate configuration
(high impedance/output enable)
- Add output-enable pins to SOMs
- Fix distroboot prioritization in connection to available devices
- Read bootscript address/flash address from DT
- Fix pcap_prog address
The StarFive VisionFive 2 board cannot load spl/u-boot-spl.bin but needs a
prefixed header. We have referring to a vendor tool (spl_tool) for this
task. 'mkimage -T sfspl' can generate the prefixed file.
Use binman to invoke mkimage for the generation of file
spl/u-boot-spl.bin.normal.out.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Standard boot has been in place for a while now. Quite a few problems
have been found and fixed. It seems like a good time to mark the
script-based approach as deprecated and encourage people to use standard
boot.
Update the DISTRO_DEFAULTS Kconfig to encourage people to move to
standard boot, which is able to boot Linux distributions automatically.
Add a short migration guide to make this easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
