Remove board_early_init_f() and board_late_init() callbacks for stm32
boards as the corresponding flags (CONFIG_BOARD_LATE_INIT and
CONFIG_BOARD_EARLY_INIT_R) are now disabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
These flags was defined and callbacks linked to these flags are empty
and only returning 0.
Remove BOARD_EARLY_INIT_F and BOARD_LATE_INIT flags for these stm32 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Check whether user has explicitly defined the mmc device to use
in mmc_get_env_dev() with CONFIG_SYS_MMC_ENV_DEV.
On STMicroelectronics boards the used mmc device for environment is
the instance of boot device provided by the ROM code; the mmc instance
is configured by alias in device tree. The used partition is defined in
device tree with u-boot,mmc-env-partition = "ssbl".
This patch allows to override this selection for the support of customer
boards without alias; for example when SDMMC1 is not used and ENV in
mmc0=SDMMC2, user can force the value: CONFIG_SYS_MMC_ENV_DEV = 0.
On STMicroelectronics boards, the current behavior is kept with
CONFIG_SYS_MMC_ENV_DEV = -1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The DSI phy can be turned on from the DSI digital interface in
the dphy_enable() function or from a dedicated DSI phy "wrapper"
in phy_ops->init() function. If the STM32MP1 case, the wrapper
is used then the dphy_enable() "warning" traces are not relevant.
This patch moves these "warning" traces to "debug" traces so
they are still available for DSI phy based on the digital
interface in debug logging mode, but not there in normal mode
for both cases.
Note: The related Linux kernel driver uses a "debug"
message too.
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove the child device of the STM32 DSI bridge when the driver probe
failed to stop futher probe request on panels used with STMicroelectronics
board (orisetech_otm8009a.c or raydium-rm68200.c driver).
This patch avoid the trace "cannot get reset GPIO" when
STM32MP157 device tree is used on stm32MP151 SOC without DSI support.
In this hw_version value is 0, as DSI bridge is absent and the panel
ofdata_to_platdata is called for each try of panel probe,
the gpio reset pin is requested but after dsi father probe failed).
For the next request, the PANEL ofdata_to_platdata failed as the gpio
is already used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The STM32MP15 boards have no reason to configure bootdelay in stm32mp1.h
as it is already done with CONFIG_BOOTDELAY (default = 2) and in
include/env_default.h.
This patch allows configuration for customers which reuse stm32mp1.h
and reduce the size of the default environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable the clocks during bsec probe when they are present in device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The command "stm32prog serial <dev>" can directly use the device sequence
number of serial uclass as this sequence number is egual to alias when it
exist; this assumption simplify the code and avoid access to gd->fdt_blob
and the device tree parsing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When serial instance is not found in device tree, the console
should be enabled and the error should be indicated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.
For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move CONFIG_CMD_STM32PROG in a specific Kconfig file for stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit d5d726d3cc ("configs: stm32mp1: only support SD card after
NOR in bootcmd_stm32mp"), the stm32mp1 boards only support SD card after
NOR boot device, so the MTD partitions for nand0 or spi-nand0 are useless
(no need of "UBI" partition in nand0 or spi-nand0).
This patch removes these nand MTD update for nor boot and simplify nand0
and spi-nand0 support (remove the mtd_boot variable).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable SCMI clock and reset domain support for stm32mp1 platform
and ARM SMC mailbox driver used as communication channel for
SCMI messages between non-secure world and secure SCMI server.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reorder include files in expected order.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Include the file needed for log function prototype, this patch solves the
compilation issue for undefined reference to `dev_err'.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This change makes stm32mp1 clock driver to get the root clocks
reference from the device node in the FDT rather than fetching
straight these clocks by their name. Driver now stores the
clock reference and use it to know if a root clock is present,
get its rate or gets its related udevice reference.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Define in the RCC clock provider node which root clocks the driver
depends on. These are root oscillators, which may be present or
not, upon FDT content.
This update binding is introduced in Linux kernel device tree by patch
"ARM: dts: stm32: move clocks/resets to SCMI resources for stm32mp15"
This patch is a preliminary step for SCMI support of stm32mp15
boards with trusted boot chain, based on TF-A or OP-TEE.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case of big area read/write on spi nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in spinand_mtd_read() and
spinand_mtd_write() to ensure that watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of big area erased on nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in nanddev_mtd_erase() to ensure that
watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of reading large area and memory-map mode is misconfigured
(memory-map size declared lower than the real size of the memory chip)
watchdog can be triggered.
Add WATCHDOG_RESET() in _stm32_qspi_read_fifo to fix it.
Issue reproduced with stm32mp157c-ev1 board and memory map size set to
1, with following command:
sf read 0xC0000000 0 0x4000000
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of big area write/erase on spi nor, watchdog timeout may occurs.
Issue reproduced on stm32mp157c-ev1 with following commands:
sf write 0xC0000000 0 0x3000000
or
sf erase 0 0x1000000
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In drivers we use a family of printing functions including pr_err() and
pr_cont(). CONFIG_LOGLEVEL is used to control which of these lead to output
via printf().
Our logging functions allow finer grained control of output. So replace
printf() by the matching logging functions. The usage of CONFIG_LOGLEVEL
remains unchanged.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When the btrfs_read_fs_root() function is searching a ROOT_ITEM with
location key offset other than -1, it currently fails via BUG_ON.
The offset can have other value than -1, though. This can happen for
example if a subvolume is renamed:
$ btrfs subvolume create X && sync
Create subvolume './X'
$ btrfs inspect-internal dump-tree /dev/root | grep -B 2 'name: X$
location key (270 ROOT_ITEM 18446744073709551615) type DIR
transid 283 data_len 0 name_len 1
name: X
$ mv X Y && sync
$ btrfs inspect-internal dump-tree /dev/root | grep -B 2 'name: Y$
location key (270 ROOT_ITEM 0) type DIR
transid 285 data_len 0 name_len 1
name: Y
As can be seen the offset changed from -1ULL to 0.
Do not fail in this case.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: David Sterba <dsterba@suse.com>
Cc: Qu Wenruo <wqu@suse.com>
Cc: Tom Rini <trini@konsulko.com>
As Stephen is no longer actively maintaining the uboot-test-hooks
repository, switch to using the instance on our GitLab.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmA5DRwACgkQ4rK92eCq
k3WKtQf+Nk2N8XzhKgoz4dfg+A/uZ1ppKiuuYfHWitvw9OLrjGO61MnYOc6Dh7De
LchPExBYnatj3lxu3IEaaNUGJRujnt9n3W8JNQTGB81MI1TO2oITEhAyDqpMGtqt
pvr1NaoxhZM4B7n/HoQnVB+XtlP08w45SQiEXjjaO82hWRk45sAZ7WGFSs60iVck
ocqhrJ/2AraG98JQPxWfvdqr+24gl1Gt++KT/cdHS//IeYJJYuiCD3m9vOj8TatH
gDVbfR6tquZ5HLvKr/orRz3smaCuutWdHcDwcjs3kFK1rBHSYFZhG3qHQ3ZqNm+w
T/7JIqz4W366o7QZXXlCoi56w2tpug==
=f/Cg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210226' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Add USB host boot support in stm32mp1 config
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
VenHw and VenMedia device path nodes may carry vendor defined data of
arbitrary length. When converting a device path node to text ensure that we
do not overrun our internal buffer.
In our implementation of
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL.ConvertDevicePathToText() we could first
determine the output length and then allocate buffers but that would nearly
double the code size. Therefore keep the preallocated buffers and truncate
excessive device paths instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fix a missing comma sign (,) from a printf(), that is only
reachable if DEBUG is defined, in which case the build fails with:
tools/mkeficapsule.c:266:36: error: expected ‘)’ before ‘bin’
266 | printf("\tbin: %s\n\ttype: %pUl\n" bin, guid);
| ^~~~
| )
Signed-off-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI spec does not allow ACPI tables to be in runtime services memory.
It recommends EfiACPIReclaimMemory.
Remove a superfluous check that the allocated pages are 16 byte aligned.
EFI pages are 4 KiB aligned.
Fixes: 86df34d42b ("efi_loader: Install ACPI configuration tables")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The board can boot with UEFI. With the latest changes in U-Boot's
EFI subsystem we also have support for EFI runtime variables, without
SetVariable support. We can also store the EFI variables in a file on the
ESP partition and preserve them across reboots.
The env and efidebug commands are missing in order to configure
EFI variables and the efibootmgr though. Since U-Boot's default config
enables other EFI related commands (e.g bootefi), let's add the env related
and efidebug commands and allow users to do that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove duplicated uart nodes introduced with commit 62f95af92a
("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.9-rc4"),
because the uart nodes wasn't correctly ordered in alphabetic order.
Only cosmetic: the generated device tree don't change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for booting from USB pen drive, since USB host port is
available on the STM32MP1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit 8745b9ebcc ("usb: gadget: add super speed support")
ums was no more functional on platform which use dwc2_udc_otg driver.
This was due to a too restrictive test which checked that the gadget
driver speed was either FS or HS.
So all gadget driver with max speed set to speed higher than
HS (SS in case of composite gadget driver in our case) are not
allowed, which is wrong.
Update the speed test in usb_gadget_register_driver() and in
dwc2_gadget_start() to allow all gadget driver speed equal or higher
than FS.
Tested on stm32mp157c-ev1 board.
Fixes: c791c8431c ("usb: dwc2: convert driver to DM_USB_GADGET")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The OUT endpoint can just be ignored as it is not used, just as the
corresponding Set_Report request for IN-only interfaces. E.g. the
Linux gadget hid keyboard also provides an interrupt endpoint.
Also cleanup confusing debug messages like "found set protocol", which
is printed when a keyboard device is found, while the Set_Protocol request
is issued quite some time later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This documents the way U-Boot understands partitions specifications.
This also updates the fastboot documentation for the changes in the
previous commit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This anchor is only for the k210 partition layout, so rename it
appropriately. This keeps it from conflicting with the (to be added)
anchor for U-Boot partitions in general.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for partitions of the form "dev.hwpart:part" and
"dev#partname". This allows one to flash to eMMC boot partitions without
having to use CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT. It also allows one to
flash to an entire device without needing CONFIG_FASTBOOT_MMC_USER_NAME.
Lastly, one can also flash MMC devices other than
CONFIG_FASTBOOT_FLASH_MMC_DEV.
Because devices can be specified explicitly, CONFIG_FASTBOOT_FLASH_MMC_DEV
is used only when necessary for existing functionality. For those cases,
fastboot_mmc_get_dev has been added as a helper function. This allows
There should be no conflicts with the existing system, but just in case, I
have ordered detection of these names after all existing names.
The fastboot_mmc_part test has been updated for these new names.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the next commit more readable by doing the move now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The only thing mmcpart was used for was to pass to blk_dselect_hwpart.
This calls blk_dselect_hwpart directly from raw_part_get_info_by_name. The
error handling is dropped, but it is reintroduced in the next commit
(albeit less specificly).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for things like "#partname" and "0.1#partname". The block
device parsing is done like in blk_get_device_part_str.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
