Add a efidebug subcommand to initiate a firmware update using the efi
firmware management protocol(fmp) set_image routine.
The firmware update can be initiated through
'efidebug capsule disk-update'
This would locate the efi capsule file on the efi system partition,
and call the platform's set_image fmp routine to initiate the firmware
update.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement the commands
* exception undefined - execute an illegal instruction
* exception sigsegv - cause a segment violation
Here is a possible output:
=> exception undefined
Illegal instruction
pc = 0x55eb8d0a7575, pc_reloc = 0x57575
Resetting ...
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present cli_simple_process_macros() requires that the caller provide
an output buffer that is exactly CONFIG_SYS_CBSIZE bytes in length. This
makes sense since it is designed to be used from the command line. But we
also want to use it for bootargs substitution.
Update the function to allow the caller to specify the buffer size. Also
return an error if the buffer is exhausted. The caller can ignore that if
preferred.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function returns 1 on success and 0 on failure. But in
the latter case it provides no indication of what went wrong.
If an attempt is made to delete a non-existent variable, the caller may
want to ignore this error. This happens when setting a non-existent
variable to "", for example.
Update the function to return 0 on success and a useful error code on
failure. Add a function comment too.
Make sure that env_set() does not return an error if it is deleting a
variable that doesn't exist. We could update env_set() to return useful
error numbers also, but that is beyond the scope of this change.
Signed-off-by: Simon Glass <sjg@chromium.org>
wip
"efidebug capsule" is more or less a debugging utility.
efidebug capsule update: invoke UpdateCapsule against data on memory
efidebug capsule show: show a capsule header
efidebug capsule result: dump a capsule result variable
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
A previous commit is adding EFI_TCG2_PROTOCOL, which in it's eventlog
support registers an EFI configuration table.
Let's add the necessary GUID so 'efidebug table' command can display
table names properly.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The current tpm2_pcr_extend is hardcoded using SHA256.
Let's make the actual command to the TPM2 configurable so we can support
a wider range of algorithms and keep the current command line as-is i.e
limited to SHA256 only
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_PROMPT_HUSH_PS2 in Kconfig, depending
on CONFIG_HUSH_PARSER, and remove the default value defined
in cli_hush.c under __U_BOOT__.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for dealing with string operands, including reading a string
from memory into an environment variable and concatenating two strings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Behún <marek.behun@nic.cz>
At present a ulong is used to hold operand values. This means that
strings cannot be used. While most operations are not useful for strings,
concatenation is. As a starting point to supporting strings, convert the
code to use a struct instead of a ulong for operands.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when more than one substitution is made this function
overwrites its buffers. Fix this bug and update the tests now that they
can pass.
Also update the debug code to show all substrings, since at present it
omits the final one.
Fixes: 855f18ea0e ("setexpr: add regex substring matching and substitution")
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the 'nlen' variable increases with each loop. If the previous
loop had back references, then subsequent loops without back references
use the wrong value of nlen. The value is larger, meaning that the string
terminator from nbuf is copied along to the main buffer, thus terminating
the string prematurely.
This leads to the final result being truncated, e.g. missing the last
(unmatched) part of the string. So "match match tail" become
"replaced replaced" instead of "replaced replaced tail".
Fix this by resetting nlen to the correct value each time around the lop.
Fixes: 855f18ea0e ("setexpr: add regex substring matching and substitution")
Signed-off-by: Simon Glass <sjg@chromium.org>
Add tests to check for buffer overflow using simple replacement as well
as back references. At present these don't fully pass.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function always allocates a large amount of stack, and
selects its own size for buffers. This makes it hard to test the code
for buffer overflow.
Separate out the inner logic of the substitution so that tests can call
this directly. This will allow checking that the algorithm does not
overflow the buffer.
Fix up one of the error lines at the same time, since it should be
printing nbuf_size, not data_size.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function assumes that a size of 4 refers to a ulong. This
is true on 32-bit machines but not commonly on 64-bit machines.
This means that the 'l' specify does not work correctly with setexpr.
Add an explicit case for 32-bit values so that 64-bit machines can still
use the 'l' specifier. On 32-bit machines, 64-bit is still not supported.
This corrects the operation of the default size (which is 4 for setexpr),
so update the tests accordingly.
The original code for reading from memory was included in 47ab5ad145
("cmd_setexpr: allow memory addresses in expressions") but I am not adding
a Fixes: tag since that code was not written with 64-bit machines in mind.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these values are open-coded in a few places. Add constants so
the meaning is clear.
Also add a comment to cmd_get_data_size()
Signed-off-by: Simon Glass <sjg@chromium.org>
As FDTDIR label doesn't specify exact file to be loaded, it should
not fail if no file exists in the directory. In this case try to boot
with internal FDT if it exists.
Signed-off-by: Anton Leontiev <aleontiev@elvees.com>
For implementing the EFI_TCG2_PROTOCOL we need the count field returned by
the TPM when reading capabilities via tpm2_get_capability().
Adjust the implementation of the 'tpm2 get_capability' command accordingly.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This command was missed when renaming getc() to getchar().
Fixes: c670aeee3d ("common: rename getc() to getchar()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This adds several commands to add, list, and remove log filters. Due to the
complexity of adding a filter, `log filter-list` uses options instead of
positional arguments.
These commands have been added as subcommands to log by using a dash to
join the subcommand and subsubcommand. This is stylistic, and they could be
converted to proper subsubcommands if it is wished.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the log level command print all valid log levels. The default
log level is annotated. This provides an easy way to see which log levels
are compiled-in.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows users to query which categories and drivers are available on
their system. This allows them to construct filter-add commands without
(e.g.) adjusting the log format to show categories and drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move parsing of log level into its own function so it can be re-used. This
also adds support for using log level names instead of just the integer
equivalent.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reduces duplicate code, and makes adding new sub-commands easier.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When rebasing this series I had to renumber all my log tests because
someone made another log test in the meantime. This involved updaing a
number in several places (C and python), and it wasn't checked by the
compiler. So I though "how hard could it be to just rewrite in C?" And
though it wasn't hard, it *was* tedious. Tests are numbered the same as
before to allow for easier review.
A note that if a test fails, everything after it will probably also fail.
This is because that test won't clean up its filters. There's no easy way
to do the cleanup, except perhaps removing all filters in a wrapper
function.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Checkpatch complains about using #ifdef for CONFIG variables.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This command lets the user list, select, and deselect mux controllers
introduced with the mux framework on the fly. It has 3 subcommands:
list, select, and deselect.
List: Lists all the mux present on the system. The muxes are listed for
each chip. The chip is identified by its device name. Each chip can have
a number of mux controllers. Each is listed in sequence and is assigned
a sequential ID based on its position in the mux chip. It lists details
like ID, whether the mux is currently selected or not, the current
state, the idle state, and the number of states.
A sample output would look something like:
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no unknown as-is 0x4
1 no 0x2 0x2 0x10
2 no 0x73 0x73 0x100
another-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x2 0x2 0x4
Select: Selects a given mux and puts it in the specified state. This
subcommand takes 3 arguments: mux chip, mux ID, state to set
the mux in. The arguments mux chip and mux ID are used to identify which
mux needs to be selected, and then it is selected to the given state.
The mux needs to be deselected before it can be selected again in
another state. The state should be a hexadecimal number.
For example:
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x1 0x1 0x4
=> mux select a-mux-controller 0 0x3
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 yes 0x3 0x1 0x4
1 no 0x1 0x1 0x4
Deselect: Deselects a given mux and puts it in its idle state. This
subcommand takes 2 arguments: the mux chip and mux ID to identify which
mux needs to be deselected. So in the above example, we can deselect mux
0 using:
=> mux deselect a-mux-controller 0
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x1 0x1 0x4
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
do_save() function defined in fs.c also supports FAT file system
re-use the same for fatwrite command.
Also fix the FAT test script to match the expected output.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Enable the command "misc" for accessing miscellaneous devices with
a MISC uclass driver. The command provides listing all MISC devices
as well as read and write functionalities via their drivers.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
The "cmd/Kconfig" has a TODO description for CMD_MISC that it should
really be named as CMD_SLEEP. Change it in the whole source tree.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Enable "optee_rpmb" command to write/read named persistent values
created on RPMB by opening session with OPTEE AVB TA.
This provides easy test for establishing a session with OPTEE
TA and storage of persistent data in MMC RPMB.
It includes following subcommands:
optee_rpmb read_pvalue:read persistent values on rpmb via OPTEE AVB TA
optee_rpmb write_pvalue:write persistent values on rpmb via OPTEE AVB
TA
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The sandbox is built with the SDL2 library with invokes the X11 library
which in turn calls getc(). But getc() in glibc is defined as
int getc(FILE *)
This does not match our definition.
int getc(void)
The sandbox crashes when called with parameter -l.
Rename our library symbol getc() to getchar().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To make the button command useful in a shell script it should return the
status of the button:
* 0 (true) - pressed, on
* 1 (false) - not pressed, off
The button command takes only one argument. Correct maxargs.
Adjust the Python unit test.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
To simplify configuration and keep synchronized the PStore/Ramoops between
U-Boot and the Linux kernel, this commit dynamically adds the Ramoops
parameters defined in the U-Boot session to the Device Tree.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch adds a new pstore command allowing to display or save ramoops
logs (oops, panic, console, ftrace and user) generated by a previous
kernel crash.
PStore parameters can be set in U-Boot configuration file, or at run-time
using "pstore set" command. Records size should be the same as the ones
used by kernel, and should be a power of 2.
This command allows:
- to display uncompressed logs
- to save compressed or uncompressed logs, compressed logs are saved as a
compressed stream, it may need some work to be able to decompress it,
e.g. adding a fake header:
"printf "\x1f\x8b\x08\x00\x00\x00\x00\x00\x00\x00" |
cat - dmesg-ramoops-0.enc.z | gzip -dc"
- ECC part is not used to check memory corruption
- only 1st FTrace log is displayed or saved
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
[trini: Minor updates for current design, correct spacing in rST]
Signed-off-by: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
At present the autoboot options are in cmd/Kconfig but they don't really
relate to commands. They relate to booting, so move this menu under the
boot menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is helpful to be able to see basic statistics about the bloblist and
also to list its contents. Add a 'bloblist' command to handle this.
Put the display functions in the bloblist modules rather than in the
command code itself. That allows showing a list from SPL, where commands
are not available.
Also make bloblist_first/next_blob() static as they are not used outside
this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
The device tree may contain a /reserved-memory node. The no-map property
of the sub-nodes signals if the memory may be accessed by the UEFI payload
or not.
In the EBBR specification (https://github.com/arm-software/ebbr) the
modeling of the reserved memory has been clarified.
If a reserved memory node in the device tree has the no-map property map,
create a EfiReservedMemoryType memory map entry else use
EfiBootServicesData.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This commits update the support of sntp to use
the framework udp. This change allows to remove
all the reference to sntp in the main network
file net/net.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For RISC-V arch, no need for CMD_IRQ so disable the same.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Add the Random Number Generator (RNG) protocol to the GUIDs that the
'efidebug dh' protocol can replace by a text.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
At present the 'bdinfo' command shows the framebuffer address, but not the
address of the copy framebuffer, if present. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the mtrr command only support 8 MTRRs. Some SoCs have more than
that. Update the implementation to support up to 10. Read the number of
MTRRs dynamically instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some HOBs include information that can be decoded. Add a -v option to the
hob command, to allow this to be displayed. Add the ability to decode a
resource descriptor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GUIDs are one of the seven evils of the computer world. They obfuscate the
meaning and require people to look up long hex strings to decode it.
Luckily only a miniscule fraction of the 10^38 possible GUIDs are in use.
Add a way to decode the GUIDs known to U-Boot. Add a few more to the list
for good measure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The 'hob' command currently lists all HOB entries. Add way to list a
single entry, by index.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
pxe sub commands need to be manually relocated for architectures which
enables MANUAL_RELOC as Microblaze.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following bugs are fixed:
* incorrect online help for setenv and env
* description of function efi_mem_carve_out()
* replace printf() by log_err() in stm32mp1_rng driver
A unit test is provided to check that the boot hart id is provided in the
RISC-V device-tree.
-----BEGIN PGP SIGNATURE-----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=vhkz
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc5-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc5 (2)
The following bugs are fixed:
* incorrect online help for setenv and env
* description of function efi_mem_carve_out()
* replace printf() by log_err() in stm32mp1_rng driver
A unit test is provided to check that the boot hart id is provided in the
RISC-V device-tree.
'env -e -i' syntax was changed from "," to ":". Account for this also
in the documentation.
Fixes: 2b3fbcb59f ("efi_loader: use ':' as separator for setenv -i")
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Correct the usage description for setenv -e too.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The bitflip test uses two equal sized memory buffers. This is achieved
by splitting the range of memory into two pieces. The address of the
second buffer, as well as the length of each buffer, were not correctly
calculated. This caused bitflip test to access beyond the end of range.
This patch fixes the pointer arithmetic problem.
A second problem arises because u-boot "mtest" command expects the
ending address to be inclusive. When computing (end - start) this
results in missing 1 byte of the requested length. The bitflip test
expects a count rather than an "ending" address. Thus it fails to test
the last word of the requested range. Fixed by using (end - start + 1).
Added Kconfig option to optionally disable the bitflip test, since it
does add significantly to the time taken for "mtest".
Fixes: 8e434cb705 ("cmd: mem: Add bitflip
memory test to alternate mtest")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds a sanity check that avoids 'size' to overflow and crash when
importing an environment that contains a checksum. Example with the wrong size
that causes the crash:
=> env import -c 0x4100000 3 v1
This assumes that v1 has already been successfully exported with
'env export -c -s 0x100 0x4100000 v1'
Signed-off-by: Pedro Aguilar <pedro.aguilar@vimar.com>
Extend Kconfig for the board with board-specific commands selection.
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add command for chimp handshake.
Handshake is used to know chimp is loaded and booted successfully.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add command to update the environmental variables which
are used to read the data from QSPI offsets and load
the binaries to bnxt.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chimp is a core in Broadcom netxtream controller (bnxt).
Add command to load binary to chimp and boot bnxt.
Signed-off-by: Trac Hoang <trac.hoang@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
* Eliminate superfluous enum value EFI_TABLE_END.
* Use correct variable type for the memory type.
* Check validity of memory type.
* Make efi_build_mem_table static.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Write log messages when booting via the bootefi command to allow tracking
on the syslog server. Example messages are
Booting /snp.efi
or
Booting /MemoryMapped(0x0,0x4fe00000,0x35a40)
Loading image failed
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The usb mass storage (f_mass_storage.c) uses fixed usb index 0,
this causes problem while CDNS3 USB controller index is 1.
Modify the API of fsg to pass the controller index.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The command 'mtrr' does not recognize the 'list' subcommand any more
since the code restructuring in commit b2a76b3fe7 ("x86: mtrr:
Restructure so command execution is in one place").
The if-else parsing the command arguments does not take 'list' into
account: the if-branch is intended for no subcommands, the else-branch
is intended for the non-list subcommands (which all expect additional
arguments). Calling the 'mtrr list' subcommand leads to a "return
CMD_RET_USAGE" in the else-branch.
Fix this by changing the else-branch to explicitly checking for
if (cmd != 'l').
Fixes: b2a76b3fe7 ("x86: mtrr: Restructure so command execution is in one place")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The commit e519f03a18 ("cmd: mem: Remove CONFIG_SYS_MEMTEST_SCRATCH
mapping") removed CONFIG_SYS_MEMTEST_SCRATCH but commit 0914011310
("command: Remove the cmd_tbl_t typedef") has added it back. That's why
symbol is still in the tree that's why remove it again.
Fixes: 0914011310 ("command: Remove the cmd_tbl_t typedef
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CMD_ADC selected DM_REGULATOR unconditionally without enabling DM.
That's why change select to depends on to cover it.
Kconfig is showing this issue as:
WARNING: unmet direct dependencies detected for REGMAP
Depends on [n]: DM [=n]
Selected by [y]:
- DM_REGULATOR_PBIAS [=y] && DM_REGULATOR [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update CMD_ADC=y configs to enable DM_REGULATOR now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove printing of the superseeded (by bi_dram[]) memory values from the
bdinfo command.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ovidiu Panait <ovidiu.panait@windriver.com>
With the planned removal of bi_memstart & bi_memsize, this patch now
moves the references to the better suiting gd->ram_base/ram_size
variables.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
Provide a command to display information about the SBI implementation.
The output might look like:
=> sbi
SBI 0.2
OpenSBI
Extensions:
sbi_set_timer
sbi_console_putchar
sbi_console_getchar
sbi_clear_ipi
sbi_send_ipi
sbi_remote_fence_i
sbi_remote_sfence_vma
sbi_remote_sfence_vma_asid
sbi_shutdown
SBI Base Functionality
Timer Extension
IPI Extension
RFENCE Extension
Hart State Management Extension
The command can be used to construct a unit test checking that the
communication with the SEE is working.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
The following bug fixes are contained in this pull-request:
* ResetSystem() should no hang if not implemented.
* Device paths in Bootxxxx variables should be verified.
* Use ':' as separator for command setenv -e -i instead of ','.
* Correct comments for functions.
* Update UEFI documentation.
-----BEGIN PGP SIGNATURE-----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=e50Q
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc3-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc3 (3)
The following bug fixes are contained in this pull-request:
* ResetSystem() should no hang if not implemented.
* Device paths in Bootxxxx variables should be verified.
* Use ':' as separator for command setenv -e -i instead of ','.
* Correct comments for functions.
* Update UEFI documentation.
setenv -e -i <address>,<filesize> can be used to set a UEFI variable
from memory.
For separating an address and a size we use ':' in most commands.
Let's do the same for setenv -e -i.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Add CCF clocks definitions for iMX6Q enet (ETH)
- Several fixes for CCF framework - the most notable is the one, which
adds get_rate helper to clk-mux.c
- Improvements for clk command - better visibility and alignment.
Update depth only when clock uclass is found to have correct display
of command "clk dump".
Without this patch, the displayed depth is the binding depth for
all the uclass and that can be strange as only clock uclass nodes
are displayed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This series includes bug fixes for:
* UEFI secure boot - images with multiple signatures
* UEFI secure boot - support for intermediate certificates
* corrections for UEFI unit tests
* missing loadaddr on MAIX board
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl82zyEACgkQxIHbvCwF
GsR8GQ/9FzCCfmhu2VhVI1cUKIT2B/FhAXbADAAhmBFk1SezhnKrsWUFFUbHeD+v
c0+QKBldIARxpD40M68FNP7QVA35iaU2+Z5jBQ7r5ZUuTuZkxeFavtHRXlSCL02R
rmdsKTtwPTRgve3IxEFJcxc4jpvAhNH+QLveK+PA+gUGjd2UoYWoGknJ4n8oe2rG
uDX4em8Sy1LXrkJLCf5Ae8+M3FBOtsBAFif1tX5cWnH5kP3DbL9A5A5JHxlVJEQi
SBC8NuJW+At89VlckEGpREt8itFMicdbLT/dSKDU3kh+l/h6zTbd9fGmoKLKXDdw
O/qwC2kwsKg/jrfZwYOTzUIpRt3jhe+CwrEajVJY12jIQzAW4kvj2mo9AeBEydHO
umFfbExGH8zwZgynrhhbjHdNxcGBahUGLoKLCkJI51I7EwCMCrN5rtUpUzxVybTE
VJKyTqlyUSIZGU4AsQT3KflLGRGU/HNS2ariQWjEbKWcCC03Q7dXH1RQMUxTlqL3
Owhqv/NI07WIvQZD3oWPkn3Z8tiQMzF370qO2gb/AwM7U0P3ggkcUxAs7mCIj5x6
81PP65di4+zRzCyU1IHCILem7LHxGR6drGatbHspGBYAJrPduyM2cYAa0eXUOCvX
Hz1GURhlVGwBdBAwaZ+g13/NtisrkRBQQYZO8jiEBqhnWoc3514=
=0ZD1
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc3 (2)
This series includes bug fixes for:
* UEFI secure boot - images with multiple signatures
* UEFI secure boot - support for intermediate certificates
* corrections for UEFI unit tests
* missing loadaddr on MAIX board
There is no need to show demo list description twice when help demo is
performed. The patch removes duplicated entry.
Current state:
=> help demo
demo - Driver model (dm) demo operations
Usage:
demo list List available demo devices
demo hello <num> [<char>] Say hello
demo light [<num>] Set or get the lights
demo status <num> Get demo device status
demo list List available demo devices
Fixes: a02af4aeec ("dm: demo: Add a simple GPIO demonstration")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add initial infrastructure for Xen para-virtualized block device.
This includes compile-time configuration and the skeleton for
the future driver implementation.
Add new class UCLASS_PVBLOCK which is going to be a parent for
virtual block devices.
Add new interface type IF_TYPE_PVBLOCK.
Implement basic driver setup by reading XenStore configuration.
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
The command 'exception' can be used to test the handling of exceptions.
Currently the exception command only allows to create an illegal
instruction exception on RISC-V.
Provide a sub-command 'exception unaligned' to cause a misaligned load
address exception.
Adjust the online help for 'exception undefined'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Variable load_options must be initialized to NULL to avoid a segmentation
fault when freeing the memory this variable points to.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Bugs in the UEFI sub-system are fixed:
* use the optional data of the BootXXXX variables as load options
* simplify function public_key_verify_signature()
* amend a copyright notice
-----BEGIN PGP SIGNATURE-----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=gMCK
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc3
Bugs in the UEFI sub-system are fixed:
* use the optional data of the BootXXXX variables as load options
* simplify function public_key_verify_signature()
* amend a copyright notice
Up to now we used the value of the bootargs environment variable as load
options in the boot manager. This is not correct. The data has to be taken
from the Boot#### variable.
Let the boot manager copy the optional data of the EFI_LOAD_OPTION as load
options to the loaded image protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The bootefi bootmgr command has to set the load options for a loaded image
from the value of BootXXXX variable. If the boot manager is not used, the
value is set from the environment variable bootargs (or efi_selftest).
Factor out a common function efi_set_load_options().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
