In order to better compare the Linux rk3288.dtsi version
with the u-boot version move the dma-controller nodes
to the DT root.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version sort the mipi,hdmi,lvds and dp nodes.
Changed:
Rename mipi_dsi label.
Rename dp nodename.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the conversion of rockchip-usb-phy.yaml a long time used fallback
string for rk3066a/rk3188 was added. The linux driver doesn't do much with
the GRF phy address range, however the u-boot driver rockchip_usb2_phy.c
does. The bits in GRF_UOC0_CON2 for rk3066a/rk3188 and rk3288 for example
don't match. Remove the usb-phy fallback string for rk3188
to prevent possible strange side effects.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change define condition in board_usb_init() function
to allow rk3066/rk3188 to use the USB PHY driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In case rtt_nom is set to 0 keep ODT disabled (MMDC MPODTCTRL = 0).
No changes required for DDR MR1 Rtt_Nom impedance register, 0 value is
already handled correctly.
No board is currently affected by this change (rtt_nom != 0 on all i.MX6
ddr3 boards), this will be used by a follow-up change.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixup thermal trips in Linux device tree according to SoC thermal
grade.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Adam Ford <aford173@gmail.com>
linux system will die if we offline one of the cpu on R40 based board:
eg: echo 0 > /sys/devices/system/cpu/cpu3/online
The reason is that the R40 version of sunxi_cpu_set_power always passes
0 for the CPU number, so we turn off CPU0, regardless of what CPU the
CPU_OFF request came for.
Fix this by passing the proper CPU number, as there are proper power
clamp registers for every of the four cores.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
The previous version of this change was only partially applied.
Fixes: 4746694cba ("ARM: dts: sun4i: Sync from Linux v5.18-rc1")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Building the sandbox with NO_SDL=1 resulted in an undefined reference to
'sandbox_sdl_remove_display'. Resolve this by adding a stub
implementation to match the stubs of the other similar functions.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This was previously needed, but U-Boot is now capable of parsing
the new "phy-connection-type" property that is already used in
the main devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This syncs the devicetree files with the latest Linux kernel (5.19-rc2).
This also fixes the currently broken ethernet support:
Before:
Net: Could not get PHY for FEC0: addr 0
After:
Net: eth0: ethernet@30be0000
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Timeouts are not expected to happen and are handled as fatal errors.
Increase all timeouts to 1 second as defensive measure to avoid relying
on the timing behaviour of certain firmware versions or configurations.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
The NVMe firmware in the macOS 13 beta blocks or crashes with u-boot's
current minimal RTKit implementation. It does not provide buffers for
the firmware's buffer requests. The ANS2 firmware included in macOS 11
and 12 tolerates this. The firmware included in the first macOS 13 beta
requires buffers for the crashlog and ioreport endpoints to function.
In the case of the NVMe the buffers are physical memory. Access to
physical memory is guarded by what Apple calls SART.
Import m1n1's SART driver (exclusively used for the NVMe controller).
Implement buffer management helpers for RTKit. These are generic since
other devices (none in u-boot so far) require different handling.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Override __udelay() as 'always inlined' function so that PSCI code
run in '__secure' section can call this delay function as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for SPI2 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for CAN1 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART5 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART4 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART3 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The third parameter of dfu_alt_add(), the string description of alternate,
is build in stm32prog_alt_add() with a unnecessary character ';' at the
end of the string.
This separator was required in the first implementation of
dfu_alt_add() but is no more needed in the current implementation;
this separator is managed only in dfu_config_interfaces() which call
dfu_alt_add() for this parameter without this separator.
And since the commit 53b406369e ("DFU: Check the number of arguments
and argument string strictly"), this added character cause an error when
the stm32prog command is executed because the third parameter of
dfu_alt_add() must be a string with a numerical value; 's' must be NULL
in the result of call in dfu_fill_entity_mmc():
third_arg = simple_strtoul(argv[2], &s, 0);
Fixes: 53b406369e ("DFU: Check the number of arguments and argument string strictly")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Currently get_tcr() takes an "el" parameter, to select the proper
version of the TCR_ELx system register.
This is problematic in case of the Apple M1, since it runs with
HCR_EL2.E2H fixed to 1, so TCR_EL2 is actually using the TCR_EL1 layout,
and we get the wrong version.
For U-Boot's purposes the only sensible choice here is the current
exception level, and indeed most callers treat it like that, so let's
remove that parameter and read the current EL inside the function.
This allows us to check for the E2H bit, and pretend it's EL1 in this
case.
There are two callers which don't care about the EL, and they pass 0,
which looks wrong, but is irrelevant in these two cases, since we don't
use the return value there. So the change cannot affect those two.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
With the move to use DM_CLK the boards uart stops working. The used
properties are not supported by the imx8mq clock driver. Thus
the correct baudrate cannot be selected. Remove this properties here and
the board can start with working uart. Keep it in the main dts because
linux handles these porperties fine.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Without this register unlock it is not possible to configure the
pinmux used for mcu spi0.
Fixes: 92e46092f2 ("arch: arm: mach-k3: am642_init: Probe ESM nodes")
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This new MMC sample select value is obtained from running
tests on multiple Stratix 10 boards and proven working.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20220428082848.12191-4-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
The generated flash.bin does not boot the imx8mn evk LPDDR4 variant
as it misses the spl.bin description in binman.
Add its entry to fix the boot on the imx8mn evk LPDDR4 variant.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Arti Zirk <art@zirk.me>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Add new lines for error messages to make them easier to read.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Since the power domain driver default select CONFIG_CLK, so we will
meet lots failures without CLK_IMX8MQ, so default select it.
Fixes: commit 4eb82c2e56 ("imx: power-domain: Get rid of SMCCC dependency")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The AArch64 TCR_ELx register is a 64-bit register, and many newer
architecture features use bits in the upper half. So far U-Boot was
igorant of those bits, trying to leave them alone.
However, in an effort to set bit 31 to 1, it failed doing so, because
the compiler sign-extended "1 << 31", so that all bits[63:31] got set.
Older ARMv8.0 cores don't define anything dangerous up there, but newer
architecture revisions do, and setting all those bits will end badly:
=================
$ qemu-system-aarch64 -cpu max ....
U-Boot 2022.07-rc1 (May 09 2022 - 15:21:00 +0100)
DRAM: 1.5 GiB
================= (hangs here)
Defining TCR_ELx_RSVD to "1U << 31" avoids the sign-extension, so all
upper bits stay at a safe 0 value. This means no more surprises when
U-Boot runs on a more capable CPU core.
Reported-by: Balaji Anandapadmanaban <Balaji.Anandapadmanaban@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Peter Collingbourne <pcc@google.com>
Since commit dffdb1f8eb ("board: ti: am64x: Use fdt functions
for ram and bank init") ddr_init() and dram_bank_init() have
switched to fdtdec for getting the memory configuration from
the am64xx dts files instead of using hardcoded values. This
requires an accessible memory node in SPL as we already have
in k3-am642-r5-evm.dts.
Make the memory node accessible in A53 SPL for both am642-sk
and am642-evm and in am642-sk R5 SPL.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean up asm/io.h by
- removing commented code
- removing outdated comments
- removing unused definitions (for mem_isa, mem_pci)
This massively improves the readability of the file.
Suggested by commits:
7ab2e47d27 ("arm: Clean up asm/io.h")
909d0399a5 ("ARM: asm/io.h: kill off confusing #ifdef __mem_pci block")
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit ba1ed5b022 ("Convert CONFIG_ARCH_MAP_SYSMEM to Kconfig") clearly
defined that this option is available for SANDBOX (was also for already
removed NDS32). That's why there is no way how this code can be enabled
with current Kconfig layout for riscv.
Based on this removing this code.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
ARCH_SUNXI selects DM_SERIAL, so the condition can never be satisfied.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When CONFIG_UART0_PORT_F is defined, we try to configure two PortF pins
(usually used for the SD card) as UART0. Some SoCs use the mux value of
3 for this, while others use 4.
The combination of Kconfig symbols we currently use was not quite right:
we mis-configure the A31, A64, H6 and H616.
Going through the list in the pinctrl driver, there are only a few older
SoCs that use a value of 4, so revert the #ifdef clause, and name those
explicitly, instead of the other way around.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This would prevent configuring non-secure regs in case gic security
extensions are not emulated in Qemu.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Commit e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
fixed SD card booting on mpc85xx boards but broke NOR booting on these
boards. Reason is that U-Boot build system for NOR images uses binman and
this binman ignores alignment defined in linker script. Instead it has own
config file where is alignment defined.
Fix binman alignment for mpc85xx boards to match what is _now_ defined in
linker script.
This change fixes building of U-Boot for NOR booting on P2020 board.
Fixes: e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
