Originally, exporting the ATF_LOAD_ADDR was required, but since binman has
been used to generate the flash.bin, it is no longer needed to do
such manual export.
The ATF address is now passed via binman.
Remove the unneeded export ATF_LOAD_ADDR line.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The format specifier for the "unsigned int" variable is documented as
"%d". However, it should be "%u". Thus, fix it.
Fixes: f5e9035043 ("doc: printf() codes")
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The usage of proftool in docs is incorrect. If proftool is used without
'-o' argument, it will show the usage like following
$ ./sandbox/tools/proftool -m sandbox/System.map -t trace -f funcgraph dump-ftrace >trace.dat
Must provide trace data, System.map file and output file
Usage: proftool [-cmtv] <cmd> <profdata>
Change '>' to '-o' to fix it.
Signed-off-by: Puhan Zhou <puh4n.zhou@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no requirement that a partition 1 exists in a partition table.
We should not try to retrieve information about it.
We should not even try reading with partition number
CONFIG_SYS_NVME_BOOT_PARTITION here as this is done in the fs_set_blk_dev()
call anyway.
Fixes: 8ce6a2e175 ("spl: blk: Support loading images from fs")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present listing a partition produces lots of errors about this
filesystem:
=> part list mmc 4
cannot find valid erofs superblock
cannot find valid erofs superblock
cannot read erofs superblock: -5
[9 more similar lines]
Use debugging rather than errors when unable to find a signature, as is
done with other filesystems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Rename defconfig to include SoC name, use similar pattern as other
RK356x boards: <soc>-<name>.dts -> <name>-<soc>_defconfig
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
-----BEGIN PGP SIGNATURE-----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=Bzgn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra
ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
Add myself as a reviewer for RK3566/RK3568/RK3588 boards that I have and
can help with review and testing of defconfig and device tree changes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Eugen Hristev <eugen.hristev@collabora.com>
Update MAINTAINERS files for RK3566/RK3568/RK3588 boards to include
related device tree files. Also replace space with tabs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Eugen Hristev <eugen.hristev@collabora.com>
Update Rockchip documentation to include RK3566/RK3568 boards already
supported. Also list Pine64 boards under RK3566 and drop defconfig to
match other listed boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Dropping Faiz Abbas from the UFS maintainer list as his e-mail ID is no
longer valid.
Adding Bhupesh Sharma who has been using this framework working on
Qualcomm Snapdragon SoCs as well as sending out fixes.
Adding myself as well to support in reviewing and testing patches.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Acked-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use a recent coreboot build for this test.
The coreboot commit is:
6f5ead14b4 mb/google/nissa/var/joxer: Update eMMC DLL settings
This is build with default settings, i.e. QEMU x86 i440fx/piix4
Add some documentation as to how to update it next time.
Signed-off-by: Simon Glass <sjg@chromium.org>
replace info logs with debug logs
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to reduce the number of people that are cc'd on a patch for
simply touching arch/arm/dts/Makefile (which is a big common file) add
an entry specifically to MAINTAINERS under the ARM entry.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Waiting 150us TC bit couldn't be enough.
If TFA lets 16 bits in USART fifo, we has to wait 16 times 87 us (time
of 10 bits (1 byte in most use cases) at a baud rate of 115200).
Fixes: b4dbc5d65a ("serial: stm32: Wait TC bit before performing initialization")
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The DHCOM SoM has two options for supplying ETHRX clock to the DWMAC
block and PHY. Either (1) ETHCK_K generates 50 MHz clock on ETH_CLK
pad for the PHY and the same 50 MHz clock are fed back to ETHRX via
internal eth_clk_fb clock connection OR (2) ETH_CLK is not used at
all, MCO2 generates 50 MHz clock on MCO2 output pad for the PHY and
the same MCO2 clock are fed back into ETHRX via ETH_RX_CLK input pad
using external pad-to-pad connection.
Option (1) has two downsides. ETHCK_K is supplied directly from either
PLL3_Q or PLL4_P, hence the PLL output is limited to exactly 50 MHz and
since the same PLL output is also used to supply SDMMC blocks, the
performance of SD and eMMC access is affected. The second downside is
that using this option, the EMI of the SoM is higher.
Option (2) solves both of those problems, so implement it here. In this
case, the PLL4_P is no longer limited and can be operated faster, at
100 MHz, which improves SDMMC performance (read performance is improved
from ~41 MiB/s to ~57 MiB/s with dd if=/dev/mmcblk1 of=/dev/null bs=64M
count=1). The EMI interference also decreases.
Ported from Linux kernel commit
73ab99aad50cd ("ARM: dts: stm32: Switch DWMAC RMII clock to MCO2 on DHCOM")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Display the STMicroelectronics logo with features VIDEO_LOGO and
SPLASH_SCREEN on STMicroelectronics boards.
With CONFIG_SYS_VENDOR = "st", the logo st.bmp is selected, loaded at the
address indicated by splashimage and centered with "splashpos=m,m".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v6.4.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The PWR_MPUCR CSTBYDIS bit is set, therefore the CA cores can never
enter CStandby state and would always end up in CStop state. Clear
the PDDS bit, which indicates the CA cores can enter CStandby state
as it makes little sense to keep it set with CSTBYDIS also set.
This does however fix a problem too. When both PWR_MPUCR and PWR_MCUCR
PDDS bits are set, then the chip enters CStandby state even though the
PWR_MCUCR CSTBYDIS is set. Clearing the PWR_MPUCR PDDS prevents that
from happening.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As reported by the datasheet (DocID027590 Rev 4) for PG12:
- AF9 -> LCD_B4
- AF14 -> LCD_B1
So replace AF14 with AF9 for PG12 in the dts.
Fixes: fe63d3cfb7 ("ARM: dts: stm32: Sync DT with v4.20 kernel for stm32f7")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
To disabled a clock in clock tree initialization for a mux of STM32MP15,
the selected clock source index is set with the latest possible index for
the number of bit used. Today this valid configuration cause a error
in U-Boot messages, for example with CLK_ETH_DISABLED, when this clock
is not needed for the used ETH PHY without crystal:
no parents defined for clk id 123
This patch change the level of this message to avoid this trace for
valid clock tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the DHSOM is in suspend state and either reset button is pushed
or IWDG2 triggers a watchdog reset, then DRAM initialization could fail
as follows:
"
RAM: DDR3L 32bits 2x4Gb 533MHz
DDR invalid size : 0x4, expected 0x40000000
DRAM init failed: -22
### ERROR ### Please RESET the board ###
"
Avoid this failure by not keeping any Buck regulators enabled during reset,
let the SoC and DRAMs power cycle fully. Since the change which keeps Buck3
VDD enabled during reset is ST specific, move this addition to ST specific
SPL board initialization so that it wouldn't affect the DHSOM .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
board_get_usable_ram_top() returns a physical address that is stored in
gd->ram_top. The return type of the function should be phys_addr_t like the
current type of gd->ram_top.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In efi_add_known_memory() we currently call board_get_usable_ram_top() with
an incorrect value 0 of parameter total_size. This leads to an incorrect
value for ram_top depending on the code in board_get_usable_ram_top().
Use the value of gd->ram_top instead which is set before relocation by
calling board_get_usable_ram_top().
Fixes: 7b78d6438a ("efi_loader: Reserve unaccessible memory")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As it is only called in bootmeth_efi.c
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* Convert comments in part.h to Sphinx style.
* Create documentation page for the partition API.
* Add the partition API page to the API index page.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Improve the description of function board_get_usable_ram_top().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
* provide a description for function lmb_is_reserved()
* improve the description of funciton lmb_is_reserved_flags()
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Upgrade certifi to the latest version, to remove e-Tugra from the root
store.
Link: https://groups.google.com/a/mozilla.org/g/dev-security-policy/c/C-HrP1SEq1A?pli=1
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The MVTWSI controller can act either as a master or slave device. When
acting as a master, the FSM is driven by the CPU. As a slave, the FSM is
driven by the bus directly. In what is (apparently) a safety mechanism,
if the bus transitions our FSM in any improper way, the FSM goes to a
"bus error" state (0x00). I could find no documented or experimental way
to get the FSM out of this state, except for a controller reset.
Since U-Boot only uses the MVTWSI controller as a bus master, this
feature only gets in the way: we do not care what happened on the bus
previously as long as the bus is ready for a new transaction. So, when
trying to start a new transaction, check for this state and reset the
controller if necessary.
Note that this should not be confused with the "deblocking" technique
(used by the `i2c reset` command), which involves pulsing SCL repeatedly
if SDA is found to be held low, in an attempt to force the bus back to
an idle state. This patch only resets the controller in case something
else had previously upset it, and (in principle) results in no
externally-observable change in behavior.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
- fix simplefb format for raspberrypi-4b
- fix typo in Kconfig
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZNnCUQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXNeWAJ9UAkaoM0B7iTAieOTSFhQNYVXlRQCeNTEISsLe
lfCsmvp0A6Fa+8dq9s0=
=Xt1C
-----END PGP SIGNATURE-----
Merge tag 'video-20230814' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix NULL dereference in vidconsole_measure()
- fix simplefb format for raspberrypi-4b
- fix typo in Kconfig
On RK3568 most pins have a configurable drive strength of level 0-5 and
some pins level 0-11. When rk3568_set_drive is called with a strength
value above 7 the drv value written to reg may overflow into the write
enable bits, resulting in a bad configuration.
This cause e.g. ethernet PHY on Radxa CM3-IO board not to work after
drive is configured according to the device tree.
Could not get PHY for ethernet@fe010000: addr 0
Level 6-11 can be configured using a second reg for some pins, however
the drv value is reused resulting in lower 6 bits being written to reg.
Input schmitt is configured in 2-bit fields on RK3568 compared to
earlier generation and 2'b10 should be used to enable input schmitt.
Change to use regmap_update_bits with a rmask to fix the overflow issue
and closer match the linux driver. Bit shift the drv value used for the
second reg to configure drive strength level 6-11. Also write correct
values for input schmitt setting.
Fixes: 1977d746aa ("rockchip: rk3568: add rk3568 pinctrl driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When raspberrpi-4b platform boots up, there are 2 sets of same bootup
log displayed on HDMI monitor screen, it looks like the screen is split
into 2 parts. The root cause is that video format of u-boot is different
from kernel. The fixing "a8r8g8b8" video format is used in u-boot, but
"r5g6b5" video format from framebuffer node is used in kernel image. In
order to avoid weird display status on screen, it needs to set the correct
parameter for simple framebuffer node even if it has existed.
Signed-off-by: Meng Li <Meng.Li@windriver.com>
When the fkms dtb overlay is used only the simple-framebuffer is
presented as a usable video display. So, add "simple-framebuffer"
compatible to enable video driver bcm2835.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
At present vidconsole_measure() tests ops->select_font before calling
ops->measure, which would result in a null dereference when the console
driver provides no ops for measure.
Fixes: b828ed7d79 ("console: Allow measuring the bounding box of text")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since srecord v1.60, option "-Little_Endian_CONSTant" is deprecated.
Fix the build warnings by updating little‐endian byte order option in
srec_cat command when generating loader header.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Once all the other drivers got torn down in preparation for the OS
to start, tear down the clock controller last. The clock controller
must be torn down last as some of the clock which get turned off
might have still been needed during the teardown stage of the other
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
align with other ROCK series.
Fixes: 2b506407c8 ("rockchip: Add MAINTAINERS entry for Radxa Rock 4C+")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
