This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Currently the following error message is seen during boot:
U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
APLL: 600000000 DPLL:1200000000 GPLL:1188000000
ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000
MMC: dwmmc@30110000: 0
Loading Environment from MMC... OK
In: serial@10210000
Out: serial@10210000
Err: serial@10210000
Model: Elgin RV1108 R1 board
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
....
Since the elgin-rv1108 does not use ADC to read the download
key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid
such error.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 8e9a8d0d0c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.
These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.
So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.
This eventually drop the explicit defined added
on supported board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
