If the device has a parent, it is instantiated from usb_hub_port_connect_change
and the portnr is right there in dev->portnr, so there is no need for this
whole dance to look it up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A bit field of DMA descriptor is on memory area of DMA. If we set data
to bit of DMA descriptor, we must be writeback data of DMA descriptor.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
RX_DESC_SIZE and TX_DESC_SIZE mean the size of the data descriptor for sh-eth.
We can acquire this in sizeof. It is not necessary to define these in define.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R8A7793 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds the preset value to register for R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds support for USB commands and USB storage device.
Signed-off-by: Yoshiyuki Ito <yoshiyuki.ito.ub@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board use SCIF2, not SCIF0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since board info structure is not still set up, the setting of RAM
address causes illegal access.
Therefore the setting of RAM address is removed.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0xB0000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The change of the CPU frequency is waited for until PLL0ST of the PLLECR is
set to 1.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Initialization of L2CTLR[5] was set only as R8A7790 by commit
237faf095f.
However, initialization of cash needs to be performed continuously.
This changes into the processing which continues initialization of
L2CTLR[5] into L2CTLR cash and performs it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Commit f91c09acf5 ("ARM: mx6: Add support for Kosagi Novena") missed to
add a MAINTAINERS file, so add Marek as the maintainer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
155fa9af95 "spi: mxc: fix sf probe when using mxc_spi" break
spi flash detection on the aristainetos board. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Set the CONFIG_MXC_GPT_HCLK configuration in mx6_common.h, so that
24Mhz OSC clock source will be selected for GPT on all MX6 platforms.
Signed-off-by: Ye.Li <B37916@freescale.com>
For MX6SL and MX6SX, the perclk can come from OSC 24Mhz source. Fix
the get_ipg_per_clk function to support it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set,
the GPT will select a high frequency clock as clock source.
Otherwise, the GPT will stay to use 32Khz OSC as clock source.
In the implementation, since only the GPT on i.MX6 series provide the
clock source option for 24Mhz OSC. For others (only i.MX5 and i.MX6
compile the driver), if the configuration is set, the perclk will be
selected as clock source.
MX6Q/D Rev 1.0 and MX6SL are special in the implementation, because they
don't have the 24Mhz OSC clock source option, so also select the perclk
for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so
eventually the clock comes from OSC 24Mhz.
Signed-off-by: Ye.Li <B37916@freescale.com>
In system boot chapter of i.MX6 reference manual, the "Image Vector Table"
figure shows the bootdata.start points to the beginning of the destination
memory. It means the bootdata.size should contain the IVT offset part,
but the calculation in imximage tool does not have.
We found this issue when booting from QuadSPI NOR on i.MX6SX. The u-boot
runs into abnormal (crash or stop) after booting. After checked the destination
memory where the image is loaded to, there are hundreds of bytes at
the image end are not loaded into memory. Since there is a 4096 bytes
round in the calculation, for the booting devices using smaller IVT offset,
such as SD and SPI booting, they are not easy to reproduce.
Signed-off-by: Ye.Li <B37916@freescale.com>
Commit 79fd7e649e
MIPS: always keep all sections in u-boot ELF binary.
Always keep all sections in u-boot ELF binary. Move all unneeded
sections after _end to avoid allocating space in the final binary.
Also remove .deadcode section which is now obsolete.
removed section .deadcode because the original symptoms were not
visible anymore. Unfortuneatly the binutils bug still exists.
The size of .rel.dyn section is often bigger than needed for all
entries. But objcopy only allocates space as much as required for all
reloc entries. Thus there is a gap between the last entry and
__rel_dyn_end in u-boot.bin. If u-boot is booted from RAM (e.g. in
SPL scenarios) that area could contain garbage data which could lead
to CPU exceptions during relocation.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Refactor and unify all compiler settings in arch/mips/config.mk.
Also add tune flags for each supported CPU type.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The vct board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The dbau1x00 board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Now the user can separately select the CPU type. Thus the
targets qemu_mips and qemu_mips64 can be merged to a single
target.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Now the user can select the CPU type for each target. Thus
CONFIG_SYS_CPU could be set globally.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add new Kconfig option to let the user select the targets
CPU type. Each target have to select SUPPORTS_CPU_MIPS[32,64]_R[1,2]
to indicate which CPU types are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add new Kconfig option to let the user select the targets
endianess. Each target have to select SUPPORTS_BIG_ENDIAN
and/or SUPPORTS_LITTLE_ENDIAN to indicate which endianess
is supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This file is not maintained these days.
We use MAINTAINERS for the maintainership of the supported boards.
For dead boards, we have some clues in doc/README.scrapyard and
also imperishable history in git-log.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-By: Wolfgang Denk <wd@denx.de>
Commit f91c09acf5 ("ARM: mx6: Add support for Kosagi Novena") missed to
add a MAINTAINERS file, so add Marek as the maintainer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Commit d58a9451e7 (ppc/arm: zap EMK boards) removed
TOP* boards support but missed to remove entries in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
The top9000 was the last board to use this header file.
It was removed by commit d58a9451e7 (ppc/arm: zap EMK boards).
[2] board/matrix_vision/common/*
Some Matrix Vision boards were dropped by commit e7a565638a
(powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
and commit af55e35d33
(powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
Since then these files have been unused.
[3] include/usb/omap1510_udc.h
The omap5912osk was the last board to use this header file.
It was removed by commit 62d636aa2a
(omap: remove omap5912osk board support).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
This enables the VMMC2 LDO, which powers the MMC2 device.
When the device starts from MMC2, this has already been enabled by the BootROM,
but when starting from peripheral boot (USB, UART), it is not the case.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch fixes a compilation warning of kwbimage.c:
tools/kwbimage.c: In function ‘kwbimage_set_header’:
tools/kwbimage.c:784:8: warning: ‘headersz’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(ptr, image, headersz);
^
Instead of using multiple if statements, use a switch statement with
a default entry. And return with error if an unsupported version
is configured in the cfg file.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-By: Wolfgang Denk <wd@denx.de>
kwbimage uses get_current_dir_name(3) which is a gnu extension and not
available on darwin host. Fix this by converting to portable getcwd(3)
function.
This patch fixes the following error:
---8<---
HOSTCC tools/kwbimage.o
tools/kwbimage.c:399:16: warning: implicit declaration of function 'get_current_dir_name' is invalid in C99 [-Wimplicit-function-declaration]
char *cwd = get_current_dir_name();
^
tools/kwbimage.c:399:10: warning: incompatible integer to pointer conversion initializing 'char *' with an expression of type 'int' [-Wint-conversion]
char *cwd = get_current_dir_name();
^ ~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
...
Undefined symbols for architecture x86_64:
"_get_current_dir_name", referenced from:
_image_headersz_v1 in kwbimage.o
ld: symbol(s) not found for architecture x86_64
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
[agust: fixed getcwd() return warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The patch below failed to define the variable, so define it
to make it consistent with M53EVK.
commit a428ac914b
Author: Lothar Rubusch <lothar@denx.de>
Date: Thu Jun 26 11:01:29 2014 +0200
ARM: m28evk: Update default environment
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
