Use the correct macro to test presence CONFIG_LED:
replace CONFIG_IS_ENABLED(CONFIG_LED) by CONFIG_IS_ENABLED(LED)
Issue see during review unrelated patch
"board: stm32mp1: update management of boot-led"
http://patchwork.ozlabs.org/patch/1264823/
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable these standard U-Boot commands for image manipulation and for
starting the default boot command using 'boot' command in U-Boot shell.
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The LED labels do not match the silkscreen on the board, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Define FMC2 base address, for use in board files, until there is an
actual FMC2 bus driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add management of property "reg" to configure @ of phy and
also "max-speed" property to specify maximum speed in Mbit/s
supported by the device
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add management of property "reset-gpios" in the node identified by
"phy-handle" to configure any GPIO used to reset the PHY.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrice CHOTARD <patrice.chotard@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Get the watchdog platform clock from the DTS file
using clk subsystem and use the same for calculating
ticks in msec.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some watchdog devices, e.g. external gpio-triggered ones, must be
reset more often than once per second, which means that the current
rate-limiting logic in watchdog_reset() fails to keep the board alive.
gpio-wdt.txt in the linux source tree defines a "hw_margin_ms"
property used to specifiy the maximum time allowed between resetting
the device. Allow any watchdog device to specify such a property, and
then use a reset period of one quarter of that. We keep the current
default of resetting once every 1000ms.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
This function is a bit large for an inline function, and for U-Boot
proper, it is called via a function pointer anyway (in board_r.c), so
cannot be inlined.
It will shortly set a global variable to be used by the
watchdog_reset() function in wdt-uclass.c, so this also allows making
that variable local to wdt-uclass.c.
The WATCHDOG_TIMEOUT_SECS define is not used elsewhere.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
Since WATCHDOG_TIMEOUT_MSECS was converted to Kconfig (commit
ca51ef7c0c), CONFIG_WATCHDOG_TIMEOUT_MSECS has been guaranteed to be
defined. So remove the dead fallback ifdeffery.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
Use the new a3700_fdt_fix_pcie_regions function in turris_mox.c so that
MOX boards with 4 GB RAM are fully supported.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
In case when ARM Trusted Firmware changes the default address of PCIe
regions (which can be done for devices with 4 GB RAM to maximize the
amount of RAM the device can use) we add code that looks at how ATF
changed the PCIe windows in the CPU Address Decoder and changes given
device-tree blob accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
In order to support MOX boards with 2 GB or 4 GB RAM, we use the new
Armada-3700 generic code for memory information structures. This is done
by removing dram_init and dram_init_banksize from turris_mox.c, in order
for the generic, weak definitions to be used.
Also for boards with 4 GB RAM it is needed to increase
CONFIG_NR_DRAM_BANKS to 2 in turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently on Armada-37xx the mem_map structure is statically defined to
map first 2 GB of memory as RAM region, and system registers and PCIe
region device region.
This is insufficient for when there is more RAM or when for example the
PCIe windows is mapped to another address by the CPU Address Decoder.
In the case when the board has 4 GB RAM, on some boards the ARM Trusted
Firmware can move the PCIe window to another address, in order to
maximize possible usable RAM.
Also the dram_init and dram_init_banksize looks for information in
device-tree, and therefore different device trees are needed for boards
with different RAM sizes.
Therefore we add code that looks at how the ARM Trusted Firmware has
configured the CPU Address Decoder windows, and then we update the
mem_map structure and compute gd->ram_size and gd->bd->bi_dram bank
base addresses and sizes accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move Armada-8k specific DRAM init code into armada-8k specific
directory.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Sort #includes alphabetically, the only exception is common.h, which is
included first in most parts of U-Boot.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Use macro MVEBU_REGISTER to access register addresses instead of
hardcoded addresses.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit e8e9715df2 requires the USB3 regulator node to have the
enable-active-high property for the regulator to work properly. The
GPIO_ACTIVE_HIGH constant is not enough anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: e8e9715df2 ("regulator: fixed: Modify enable-active-high...")
Reviewed-by: Stefan Roese <sr@denx.de>
Patch Linux's device tree according to which Mox modules are connected.
Linux's device tree has all possible Mox module nodes preprogrammed, but
in disabled state.
If MOX B, MOX F or MOX G module is present, this code enables the PCI
node.
For the network modules (MOX C, MOX D and MOX E) are present, the code
enables corresponding ethernet and swtich nodes and DSA connections.
For the SFP cage the SFP GPIO controller node and SFP node are also
enabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
With recent changes to the mmc subsystem (chip detect code etc) update
the sdhci node of the Turris Mox device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The SPI clock signal changes value when the SPI configuration register
is configured. This can sometimes lead to the device misinterpreting
the enablement of the SPI controller as actual clock tick.
This can be solved by first setting the SPI CS1 pin from GPIO to SPI mode,
and only after that writing the SPI configuration register.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Switch to explicitly using the Pro variant DT, which has been
available since Linux 4.11.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Migrate the values for ENV_SIZE and ENV_OFFSET into board specific
Kconfig defaults so they're more accessible for configuration.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add reasonable default SPI offsets and ENV size when configured to
boot from SPI flash.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Unify the location of DT selection into board_late_init instead of
split between detection and static configuration paths.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately
configured for SATA usage.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
While newer Linux kernels provide autoconfiguration of SFP, provide
an option for setting in U-Boot Kconfig for use prior to booting.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a unique entry for ClearFog Base variant, reflected in the board
name and adjusted SerDes topology.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Make the board version printed indicate the Pro variant default.
Also adjust static name casing to match what is expected for
EEPROM product name to share string constants.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Using a consistent hardcoded MAC address from the DTS file causes
issues when using multiple devices on the same network segment.
Instead rely on environment configuration or random generation.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable distro bootcmd support for additional SATA ports if enabled.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Include attempting to boot from SCSI (SATA) devices within generated
board distro bootcmd environment. The reasoning for boot ordering is
that MMC and USB are external and removable, while when a case is in
use, replacing M.2 or mSATA drives requires disassembly. Therefore,
to boot SCSI, [bootable] external media must be removed. If SCSI were
placed before MMC or USB, then removing a bootable SCSI drive to
enable MMC or USB booting would be more difficult.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the RTC (Read Timing Control) values for PCIe memory wrappers
following an ERRATA (ERRATA# TDB). This means the PCIe accesses will
used slower memory Read Timing, to allow more efficient energy
consumption, in order to lower the minimum VDD of the memory. Will lead
to more robust memory when voltage drop occurs (VDDSEG)
The code is based on changes from Marvell's U-Boot, specifically:
20cd270407eb608a7c8dc4af19ae2b
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Support for sata devices via the scsi command is available and already
enabled by default for the Clearfog Base and Pro. This change adds scsi
to the list of boot targets used by distro-boot.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
The value of local variable ecc is immediately overwritten. So we can
remove the first assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Sort the Armada series dts in the Makefile alphabetically
prior to adding new board support.
Signed-off-by: Josip Kelečić <josip.kelecic@sartura.hr>
Reviewed-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add all TI specific drivers, include, arch files under ARM TI entry.
Driver files are added only if there is no entry for the specific
subsystem in MAINTAINERS file.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
- Add a boot logic in the distro boot command
- Add fallback mechanism in alternate boot command
- Keep single boot target -> ubifs0
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
- As there is a requirement to store certain data, we need a persistent
storage in u-boot. Hence, we need to save env in NAND
- Add default Guardian environment variables
- Update partition table:
- Reserve some space for experimentation, this ensures proper
backwards compatibility
- Update defconfig accordingly
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
This patch enables the guardian board to provide feedback
about the boot stage in headless mode. The on-board led
would behave in the following pattern
* U-boot -> GLOW LED
* Linux -> BLINK LED [HEART-BEAT PATTERN]
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
- On Guardian board, usb-eth boot in SPL stage fails due to certain
misconfiguration. Hence, add the same to fix the issue.
- configs are set based on the conditional statement present in
arch/arm/mach-omap2/am33xx/board.c
- disable tiny printf in SPL stage:
As the library is optimized, the ability to deal with ethaddr is lost.
The following message would be printed on the console,
Error: flags type check failure for "ethaddr" <= "80a81144M" (type: m)
Error inserting "ethaddr" variable, errno=1
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
For some layouts it is necessary to adjust the CK_DELAY parameter to
successfully complete DDR training. Add the ability to specify the
CK_DELAY in the mv_ddr_topology_map.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
