This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.
The following build error is reported if DM watchdog support was
enabled in SPL:
CC spl/drivers/usb/gadget/rndis.o
LD spl/drivers/usb/gadget/built-in.o
LD spl/drivers/usb/musb-new/built-in.o
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.
Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds device tree and driver model watchdog support,
converts the legacy omap watchdog driver to driver model for
TI AM335x chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_HW_WATCHDOG is no more a default option for AM33XX devices
after DT/DM conversion, adjusted kconfig accordingly.
DM watchdog support is enabled by default in SPL. The SPL image
doesn't fit into SRAM because of size constraints and build breaks
with an overflow. For this reason DM watchdog support should be
disabled in SPL, driver code should be adjusted accordingly to serve
this purpose.
Built and tested on AM335x device (BeagleboneBlack), compile tested
for all other AM33xx based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The SPL for the Overo board does not initialise the MMC. Hence, it
cannot load the main boot loader from the SD card susequently. This
patch moves the initialisation code for the MMC so it gets included in
the SPL.
[trini: Add missing header]
Signed-off-by: Tom Rini <trini@konsulko.com>
giedi and deneb are i.MX8X based and have additional data with
WLAN MAC in factoryset container. Enable building for these
boards and adapt factoryset functions to set WLAN MAC and dtb
name in environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
For new boards we always enable DM_I2C. Extend factoryset functions
to support EEPROM reading on these boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
Add a few bits of platform code to support R8A77980 V3H SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import R8A77980 V3H DTs and headers from Linux 5.2.7 , commit 5697a9d3d55f.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix various type warnings when building this driver for 64bit machine.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A77980 V3H gether needs a few minor adjustments to the sh_eth
driver, add them to support ethernet on R8A77980.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove obsolete legacy usbboot wrapper, as distroboot can handle
booting from USB drivers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When mainline kernels reboot TK1 they use SW_RESET,
that reset mode does not reset PMIC. Some rails
need to be off for RAM Re-repair to work correctly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove video=tegrafb0:640x480-16@60 aka VESA VGA mode from vidargs in
order for the panel specification in the device tree to be used. This
causes the default to be the 10.1" LVDS display which will be available
in the Toradex webshop shortly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Switch to the generic compressed Kernel image type (zImage) instead of
the U-Boot specific uImage format.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Let the kernel print some debug messages when a user program
crashes due to an exception.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use unified values for USB Product/Vendor numbers
when the config block is missing
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Make sure the Apalis GPIO 8 aka FAN_EN is on when using Apalis TK1
modules.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
By keeping RESET_MOCI_CTRL low we avoid explicitly releasing
RESET_MOCI#.
Please note that module hardware versions up to V1.1A will already
release RESET_MOCI# in hardware coming out of reset.
Please further note that with this change the USB hub on the Apalis
Evaluation board is kept in reset in U-Boot and therefore none of its
ports are operational in U-Boot.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We never really added a sensible DFU configuration for platforms
based on eMMC. Most of the things one might want to do can also be done
with UMS or fastboot, so drop the DFU configuration.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is a configuration option specific to the tegra controller.
Doing it this way makes it show up directly under the tegra controller
option, indented one level, as "Disable external clock loopback".
The way it is now, it shows up at the end of the controller list, not
indented, as if it's some kind of generic MMC configuration option.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For U-Boot we allow a GPIO to be specified to enable the codec. Add this
to the relevant binding files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This file was missed when adding the sound driver to U-Boot. Bring it in
from Linux 5.0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This file was missed when adding the sound driver to U-Boot. Bring it in
from Linux 5.0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The setting up MTRRs have already been done in previous
Slim Bootloader stages.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add slimbootloader board to run U-boot as a Slim Bootloader payload
- Add new board/intel/slimbootloader directory with minimum codes
- Add slimbootloader configuration files
- Add doc/board/intel/slimbootloader.rst
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add slimbootloader board MAINTAINERS file]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a new device tree which has very minimum nodes
- x86 reset
- x86 tsc_timer
- x86 pci
- Slim Bootloader serial
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Slim Bootloader already calibrated TSC and provides it to U-Boot.
Therefore, U-Boot does not have to re-calibrate TSC.
Configuring tsc_base and clock_rate makes x86 tsc_timer driver bypass
TSC calibration and use the provided TSC frequency.
- Get TSC frequency from performance info hob
- Set tsc_base and clock_rate for tsc_timer driver
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Slim Bootloader provides serial port info thru its HOB list pointer.
All these HOBs are eligible for Slim Bootloader based board only.
- Get serial port information from the serial port info HOB
- Leverage ns16550 driver with slimbootloader specific platform data
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Slim Bootloader provides memory map info thru its HOB list pointer.
Configure memory size and relocation memory from the HOB data, and
provide e820 entries as well.
- Get memory size from the memory map info HOB
- Set available top memory lower than 4GB for U-Boot relocation
- Provide e820 entries from the memory map info HOB
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
FSP (CONFIG_HAVE_FSP) and Slim Bootloader (CONFIG_SYS_SLIMBOOTLOADER)
consume HOB (CONFIG_USE_HOB) data from the each HOB list pointer.
Add a common HOB library in lib/hob.c and include/asm/hob.h.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use existing EFI_GUID and efi_guid_t instead of struct efi_guid.
This is pre-work before making a common HOB library.
- Change 'struct efi_guid' to efi_guit_t
- Remove 'struct efi_guid'
- Define GUIDs with EFI_GUID() macro
- Use guidcmp() instead of compare_guid()
- Remove compare_guid()
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on MinnowMax
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This slimbootloader CPU type is to enable U-Boot as a payload which
runs on top of Slim Bootloader (https://github.com/slimbootloader).
The Slim Bootloader is designed with multi-stage architecture for
the execution from reset vector to OS booting, and supports QEMU,
Apollolake, Whiskeylake and Coffeelake platforms consuming Intel
FSP (https://github.com/IntelFsp) for silicon initialization
including CAR and memory initialization.
The Slim Bootloader generates new HOB (Hand Off Block) which are
serial port info, memory map info, performance data info and so on,
and passes it to a Payload. U-Boot as a payload will use these HOB
information for basic initialization such as serial console.
As an initial commit,
- Add CONFIG_SYS_SLIMBOOTLOADER to enable slimbootloader CPU type
- Add new arch/x86/cpu/slimbootloader directory with minimum codes
- Get hob_list pointer from Slim Bootloader
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With the introduction of the new spi-mem model operations changed
slightly. The new spi-mem operations make things a bit easier to
handle for ich-spi flash interface. This patch converts the ich-spi
driver by using spi-mem operations.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on Intel CrownBay and MinnowMax
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix compiler warnings when building the driver for 64-bit]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Remove a stray break which suppresses some debug messages.
Indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
At present the iasl tool (Intel ACPI (Advanced Configuration and Power
Interface) Source Language Compiler) is called in such a way that it uses
the source directory for its temporary files.
This means we end up with these files when building x86 boards:
board/dfi/dfi-bt700/dsdt.aml
board/dfi/dfi-bt700/dsdt.asl.tmp
Update the code to put temporary files in the target directory instead.
The iasl tool is quite confusing since it generates files with different
extensions and does not allow these to be individually specified. Add some
documentation to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove dsdt.hex from 'make clean' rules and correct U-Boot spelling]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Intel Tangier has a shared DMA controller that, according to Microsoft spec,
has to be presented in CSRT table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ACPI has a capability to specify DMA parameters for DMA channel consumers.
To enable this for Intel Edison, describe GP DMA device in ACPI table
in order to get an ACPI handle to it in OS.
This works in conjunction with CSRT, which must be in align with DSDT.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Here is a stub function that generates an empty CSRT. If the target platform
provides acpi_fill_csrt() function, it will be used to populate the table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With qemu-x86 starting to use config_distro_bootcmd, the pre-defined
ramboot and nfsboot commands do not work any more. This is caused by
undefined environment variable 'ramdiskaddr' that was previously set
in CONFIG_EXTRA_ENV_SETTINGS but later CONFIG_EXTRA_ENV_SETTINGS was
redefined for distro boot.
Update the x86 generic CONFIG_EXTRA_ENV_SETTINGS to consider distro
boot, and remove the one in qemu-x86.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Converts qemu x86 machines to boot using distro_config. The intent is to
allow u-boot in qemu to be maximally compatible with many boot methods
without having to change the config. Previously, u-boot would only boot
in a very limited set of circumstances where there was a /boot/vmlinuz
on scsi 0:3 with no ramdisk.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: convert doc updates to reST]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
