Commit graph

36 commits

Author SHA1 Message Date
Marek Vasut
6757fa5756 serial: mxc: Add iMX6SX compatible string
Add compatible string for iMX6SX.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Adam Ford
e434b414fb imx: serial_mxc: use CONFIG_IS_ENABLED instead of ifdef
Kconfig allows boards to configured with DM_SERIAL and still
have SPL_DM_SERIAL disabled.  This patch changes the ifdef's
to CONFIG_IS_ENABLED to allow the modes to differ between
SPL and U-Boot.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2019-03-13 09:14:35 +01:00
Max Krummenacher
a24532083c imx: serial_mxc: disable ri and dcd irq in dte mode
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.

Disable the bits to prevent an interrupt storm when Linux enables
the UART interrupts.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-02-15 22:01:15 +01:00
Bin Meng
4687919684 serial: Remove DM_FLAG_PRE_RELOC flag in various drivers
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.

To mitigate this potential impact, the following changes are
implemented:

- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
  only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
  is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
  drivers that support both statically declared devices and
  configuration from device tree

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-14 09:16:28 -08:00
Bernhard Messerklinger
4684fa8bdd serial: mxc: Add match string for i.mx6 quad/dual lite serial
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2018-10-22 18:56:17 +02:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Jagan Teki
61366b71a8 serial: mxc: Add debug uart support
Add support for the debug UART to assist with early debugging.
Enable it for i.CoreM6 as an example.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-12 09:44:22 +02:00
Jagan Teki
52c14cabda serial: mxc: Code cleanup
- Remove space between #define to macro
- Add tab between macro and value

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-12 09:42:33 +02:00
Jagan Teki
45d97511a9 serial: mxc: Move common baud gen into _mxc_serial_setbrg
Move the common baud generation code into _mxc_serial_setbrg
so-that dm and non-dm can call this func.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-12 09:42:33 +02:00
Jagan Teki
97548d5947 serial: mxc: Move common init into _mxc_serial_init
Move the common initialization code into _mxc_serial_init
so-that dm and non-dm can call this func.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-12 09:42:33 +02:00
Jagan Teki
57d3e98f57 serial: mxc: Move cr1 and cr2 write to mxc_serial_setbrg
Control reg write should be part of setbrg for better
buadrate generation, so move cr1 and cr2 write to
mxc_serial_setbrg

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-12 09:42:33 +02:00
Jagan Teki
62af03ee97 serial: mxc: Use RFDIV in dm-code
Use RFDIV in dm-code instead of numeric value, so-that
it can be common for dm and non-dm.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-12 09:42:33 +02:00
Jagan Teki
ffa8bcd7f1 serial: mxc: Add common mxc_uart reg space
This patch will add common reg space for non-dm and
dm code and non-dm reg space can be accessed using
mxc_base.

This will
- get rid of __REG volatile assignments
- Make common reg_space by removing unneeded macros

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-12 09:42:33 +02:00
Simon Glass
a821c4af79 dm: Rename dev_addr..() functions
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

   1. dev_read_addr...()    - works on devices, supports flat/live tree
   2. devfdt_get_addr...()  - current functions, flat tree only
   3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:01 -06:00
Sébastien Szymanski
3a5d63635d dm: imx: serial: add i.MX6UL support
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2017-03-19 17:24:13 +01:00
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Stefan Agner
a99546ab62 dm: imx: serial: support device tree
Support instatiation through device tree. Also parse the fsl,dte-mode
property to determine whether DTE mode shall be used.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-07 12:26:14 +02:00
Breno Lima
5d219d46aa serial_mxc: Remove unconditional DCE setting
Commit 83fd908f28 ("dm: imx: serial: Support DTE mode when using driver
model") breaks the serial output for the imx boards that do not use
the serial driver model.

The reason for the breakage is that it's setting UFCR_DCEDTE
unconditionally for the non-dm case.

So keep the original behavior by removing UFCR_DCEDTE setting in the
non-dm case.

Tested on mx7sabresd and mx6wandboard.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-21 10:43:52 +02:00
Stefan Agner
83fd908f28 dm: imx: serial: Support DTE mode when using driver model
The MXC UART IP can be run in DTE or DCE mode. This depends on the
board wiring and the pinmux used and hence is board specific. This
extends platform data with a new field to choose wheather DTE
mode shall be used.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-19 19:52:13 +02:00
Alison Wang
055457ef25 serial: Move carriage return before line feed for some serial drivers
In general, a carriage return needs to execute before a line feed.
The patch is to change some serial drivers based on this rule, such
as serial_mxc.c, serial_pxa.c, serial_s3c24x0.c and usbtty.c.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-14 15:34:50 -06:00
Maximilian Schwerin
434afa809e serial_mxc: Fix setup of UARTx_UFCR register
This patch writes the default values for TXTL and RXTL to UARTx_UFCR.
Without this patch some older kernel versions crash as UARTx_UFCR was
not always correctly initialized.

Signed-off-by: Maximilian Schwerin <maximilian.schwerin@tigris.de>
2016-01-03 15:22:11 +01:00
Masahiro Yamada
86256b796e dm: move platform data headers to include/dm/platform_data
The platform_data definitions are generally referenced from both
drivers and board files.  That is why header files defining
platform_data sturectures are placed in "include" directory,
but our top level "include" directory is already too cluttered.

Let's collect platform_data definitions under the directory
"include/dm/platform_data" like Linux gathers ones around under
"include/linux/platform_data".

This commit moves two header files:

  include/serial_mxc.h -> include/dm/platform_data/serial_mxc.h
  include/serial_pl01x.h -> include/dm/platform_data/serial_pl01x.h

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-23 21:43:07 -06:00
Simon Glass
a8ba569cba dm: imx: serial: Support driver model in the MXC serial driver
Add driver model support with this driver. Boards which use this driver
should define platform data in their board files.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22 10:36:56 -06:00
Eric Nelson
3a56482590 serial_mxc: disable new features of autobaud detection
Bit 7 of UCR3 is described in the i.MX3x/i.MX5x/i.MX6x
reference manuals as follows:

	Autobaud Detection Not Improved-. Disables new features of
	autobaud detection (See Baud Rate Automatic Detection
        Protocol, for more details).

	0 Autobaud detection new features selected
	1 Keep old autobaud detection mechanism

On at least i.MX6DQ, i.MX6DLS and i.MX53, the "new features"
occasionally cause the receiver to get out of sync and
continuously produce received characters of '\xff'.

This patch disables the "new feature" on all boards, since
there's no support for auto-baud in U-Boot on any of them.

More details are available in this post on i.MX Community:
	https://community.freescale.com/message/403254

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-05-28 17:37:47 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Marek Vasut
ec3fd68952 serial: Use default_serial_puts() in drivers
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
2012-10-17 07:55:50 -07:00
Marek Vasut
a382725060 serial: Remove CONFIG_SERIAL_MULTI from serial drivers
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15 11:53:58 -07:00
Marek Vasut
a943472c23 serial: arm: Implement CONFIG_SERIAL_MULTI into mxc serial driver
Implement support for CONFIG_SERIAL_MULTI into mxc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mxc driver. Also, add a weak implementation
of default_serial_console() returning this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:53:56 -07:00
Stefano Babic
40f6fffee5 MX: serial_mxc: cleanup removing nasty #ifdef
The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Helmut Raiger <helmut.raiger@hale.at>
CC: John Rigby <jcrigby@gmail.com>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
2011-12-06 23:59:40 +01:00
Stefano Babic
8627111543 IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27 19:38:05 +02:00
Stefano Babic
1b22b0d35b serial_mxc: add support for Freescale's i.MX35 processor
The patch adds UART support for the i.MX35 processor.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-02-02 00:54:42 +01:00
Liu Hui-R64343
0c466ad017 serial_mxc: add support for MX53 processor
This patch add UART support for Freescale MX53 processor

Signed-off-by: Jason Liu <r64343@freescale.com>
2011-02-02 00:54:41 +01:00
Stefano Babic
4ec3d2a745 MXC: Add watchdog support to serial driver
Calls WATCHDOG_RESET() inside serial driver
for boards enabling watchdog.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-29 11:24:31 +02:00
John Rigby
552ff8f1d9 Add support for Freescale MX25 SOC
ARM926EJS core with MX31 peripherals.

Signed-off-by: John Rigby <jcrigby@gmail.com>
Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
2010-03-07 12:36:36 -06:00
Stefano Babic
71d64c0e4f serial_mxc: add support for MX51 processor
The patch adds support for the Freescale mx51 processor.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
2010-03-07 12:36:35 -06:00
Ilya Yanok
47d19da4d3 serial_mx31: allow it to work with mx27 too and rename to serial_mxc
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-06-21 16:18:13 +02:00
Renamed from drivers/serial/serial_mx31.c (Browse further)