When build for arm64 target, comipler reports the following warning:
drivers/spi/bcm63xx_hsspi.c: In function ‘bcm63xx_hsspi_xfer_dummy_cs’:
include/linux/kernel.h:184:17: warning: comparison of distinct pointer
types lacks a cast
184 | (void) (&_min1 == &_min2); \
| ^~
drivers/spi/bcm63xx_hsspi.c:298:22: note: in expansion of macro ‘min’
298 | size_t curr_step = min(step_size, data_bytes);
This change fix this warning by casting the data_bytes to size_t.
Fixes: 0e144ec38c ("spi: bcm63xx-hsspi: Add prepend mode support")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
The wdt_start function takes timeout_ms as a parameter and starts the
watchdog with this value. However, when you output the message, it shows
the default timeout value for the watchdog device.
So this patch fixes that part to output the correct timeout value.
Before -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (60s timeout)
After -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (3s timeout)
Fixes: c2fd0ca1a8 ("watchdog: Integrate watchdog triggering into the cyclic framework")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Compiling with CONFIG_USB_XHCI_PCI and CONFIG_PCI=n results in
usb/host/xhci-pci.c:48:(.text.xhci_pci_probe+0x44):
undefined reference to `dm_pci_write_config32
Add the missing Kconfig dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Like Rockchip RK3328 and RK3568, the RK3588 also have a single node to
represent the glue and ctrl for USB 3.0.
Use rk_ops as driver data to select correct ctrl node for RK3588 DWC3.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
We need to get the DMA address before incrementing the pointer, as that
might move us onto another segment.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Now that we always check the return value, just return NULL on timeouts.
We can still log the error since this is a problem, but it's not reason
to panic.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
This isn't going to work, don't pretend it will and then end up timing
out.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is currently no codepath to recover from this case. In principle
we could require that the upper layer do this explicitly, but let's just
do it in xHCI when the next bulk transfer is started, since that
reasonably implies whatever caused the problem has been dealt with.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is a race where an endpoint may halt by itself while we are trying
to halt it, which results in a context state error. See xHCI 4.6.9 which
mentions this case.
This also avoids BUGging when we attempt to stop an endpoint which was
already stopped to begin with, which is probably a bug elsewhere but
not a good reason to crash.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
If the xHC has a problem with our STOP ENDPOINT command, it is likely to
return a completion directly instead of first a transfer event for the
in-progress transfer. Handle that more gracefully.
We still BUG() on the error code, but at least we don't end up timing
out on the event and ending up with unexpected event errors.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
xhci_wait_for_event returns NULL on timeout, so the caller always has to
check for that. This addresses immediate explosions in this part
of the code when timeouts happen, but not the root cause for the
timeout.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
The "i2cbcdev" sneaked in when implementing this function for the
bootcounter use case. Obviously the intention was to use prop_name
instead.
Fixes: b483552773 (i2c: Implement i2c_get_chip_by_phandle())
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
As the address read from device tree is being cast to a pointer, it's
better to use dev_read_addr_ptr() API for getting that address. The more
detailed explanation can be found in commit a12a73b664 ("drivers: use
dev_read_addr_ptr when cast to pointer").
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Just some minor style fixes. No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Get rid of magic numbers in s5p_serial_init() when writing to UART
registers. While at it, use BIT() macro for existing constants when
appropriate.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use dev_read_u8_default() instead of fdtdec_get_int() to read the "id"
property from device tree, as suggested in [1]. dev_* API is already
used in this driver, so there is no reason to stick to fdtdec_* API.
This also fixes checkpatch warning:
WARNING: Use the livetree API (dev_read_...)
[1] doc/develop/driver-model/livetree.rst
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It's not really needed here anymore. Remove it, as common.h is going
away at some point.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ChipIdea device controller wasn't properly cleaned up when disabled.
So enabling it again left it in a broken state. The problem occurred for
example when the host unbinds the driver and binds it again.
During the first setup, when the out request is queued, the endpoint is
primed (`epprime`). If the endpoint is then disabled, it stayed primed
with the initial buffer. So after the endpoint is re-enabled, the device
controller and device driver were out of sync: the new out request was
in the driver queue head, yet not submitted, but the "complete" function
was still called, since the endpoint was primed with the old buffer.
With the fastboot function this error led to the (rather confusing)
error message "buffer overflow".
Fixed by clearing the primed buffers with the `epflush` (`ENDPTFLUSH`)
register.
Signed-off-by: Simon Holesch <simon@holesch.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20231120002024.32865-1-simon@holesch.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
SCSI device scan code was executing TEST UNIT READY command without
explicitly setting dma direction in struct scsi_cmd to NONE, so command
was passed to driver with dma direction set to DMA_FROM_DEVICE,
inherited from older usage.
With WDC SDINDDH6-64G ufs device, that caused TEST UNIT READY to
return error.
Fix that, by explicitly setting dma direction to NONE for
TEST UNIT READY, and restoring it back DMA_FROM_DEVICE for the
following READ CAPACITY.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Marek Vasut <marex@denx.de>
According to the virtio v1.x "entropy device" specification, a virtio-rng
device is supposed to always return at least one byte of entropy.
However the virtio v0.9 spec does not mention such a requirement.
The Arm Fixed Virtual Platform (FVP) implementation of virtio-rng always
returns 8 bytes less of entropy than requested. If 8 bytes or less are
requested, it will return 0 bytes.
This behaviour makes U-Boot's virtio_rng_read() implementation go into an
endless loop, hanging the system.
Work around this problem by always requesting 8 bytes more than needed,
but only if a previous call to virtqueue_get_buf() returned 0 bytes.
This should never trigger on a v1.x spec compliant implementation, but
fixes the hang on the Arm FVP.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Peter Hoyes <peter.hoyes@arm.com>
CONFIG_DM_WARN has a text indicating that these messages should only
provided when debugging. This implies that the setting must be default no.
We should still create debug messages.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The clk-pll.h is going to be included in multiple files soon. Add
missing header guard to prevent possible build errors in future.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 166097e877 ("clk: exynos: add clock driver for Exynos7420 Soc")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
clk_get_by_index() returns negative number on error. Assigning it to
unsigned int makes the subsequent "ret < 0" check always false, leading
in turn to possible unhandled errors. Change 'ret' variable type to
signed int so the code checks and handles clk_get_by_index() return code
properly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: cf75cdf96e ("serial: s5p: use clock api to get clock rate")
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
s5p watchdog driver calls samsung_get_base_watchdog() function, but its
prototype is not included. That might lead to build warnings like this:
drivers/watchdog/s5p_wdt.c: In function 'wdt_stop':
drivers/watchdog/s5p_wdt.c:16:26:
warning: implicit declaration of function
'samsung_get_base_watchdog' [-Wimplicit-function-declaration]
16 | (struct s5p_watchdog *)samsung_get_base_watchdog();
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Include asm/arch/cpu.h to fix that issue.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently the renesas_sdhi_reset_tuning() unconditionally leaves SDHI
clock enabled after the tuning reset. This is not always necessary.
After the driver performed tuning reset at the end of probe function,
or in the unlikely case that tuning failed during regular operation,
the SDHI clock can be disabled after the tuning reset. The following
set_ios call would reconfigure the clock as needed.
In case of regular set_ios call which requires a tuning reset, keep
the clock enabled or disabled according to the mmc->clk_disable state.
With this in place, the controllers which have not been accessed via
block subsystem after boot are left in quiescent state. However, if an
MMC device is used e.g. for environment storage, that controller would
be accessed during the environment load and left active, including its
clock which would still be generated. This is due to the design of the
MMC subsystem, which does not deinit a controller after it was started
once, the controller is only deinited in case of mmc rescan, or before
OS boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
The X-Powers AXP313a is a small PMIC with just three buck converters and
three LDOs, one of which is actually fixed (so not modelled here).
Add the compatible string and the respective regulator ranges to allow
drivers to adjust voltages.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
On boards using the AXP313 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and
DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before
DRAM controller initialization. Therefore, this buffer must be placed in
the .data section.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
commit 95168d77d3 ("sunxi: add Allwinner R528/T113 SoC support") added
the new entry out of order.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
CONFIG_ARCH_SUNXI will not be enabled for RISC-V SoCs using this driver.
Use the symbol for the driver itself instead.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this
driver is never enabled in SPL, so the condition is always true.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
So far we have a convoluted #ifdef mesh that guards the early AXP PMIC
setup in board.c. That combination of &&, || and negations is very hard
to read, maintain and especially to extend.
Fortunately we have those same conditions already modelled in the
Kconfig file, so they are actually redundant. On top of that the real
reason we have those preprocessor guards in the first place is about the
symbols that are *conditionally* defined: without #ifdefs the build
would break because of them being undefined for many boards.
To simplify this, just change the guards to actually look at the symbols
needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER.
This drastically improves the readability of this code, and makes adding
PMIC support a pure Kconfig matter.
Doing this revealed one bug in Kconfig: there is no axp_set_dcdc4() for
the AXP818, even though CONFIG_AXP_DCDC4_VOLT includes that PMIC.
Since the AXP818 wasn't included when calling axp_set_dcdc4() in board.c,
this wasn't an issue, but becomes one now, so also remove the AXP818 from
the DCDC4 Kconfig symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
During bootstd scanning for bootdevs, if bootdev_hunt_drv() encounters
a device not found error (e.g. ENOENT), let it return a successful status
so that bootstd will continue scanning the next devices, not stopping
prematurely.
Background:
During scanning for bootflows, it's possible for bootstd to encounter a
faulty device controller. Also when the same u-boot is used for another
variant of the same board, some device controller such as SATA might
not exist.
I've found this issue while converting the Marvell Sheevaplug board to
use bootstd. This board has 2 variants, the original Sheevaplug has MMC and
USB only, but the later variant comes with USB, MMC, and eSATA ports. We
have been using the same u-boot (starting with CONFIG_IDE and later with DM
CONFIG_SATA) for both variants. This worked well with the old
envs-scripting booting scheme.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A power domain id on sandbox should be in the range from zero to
ARRAY_SIZE(scmi_pwdom) - 1. Correct the validity check logic.
Addresses-Coverity-ID: 467401 ("Out-of-bounds write")
Addresses-Coverity-ID: 467405 ("Out-of-bounds read")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
When we do not have CONFIG_BOUNCE_BUFFER enabled, inside of
scsi_init_dev_desc_priv we never set the 'bb' field to false, we only
initialize it to true when CONFIG_BOUNCE_BUFFER is set. Given that we
have a number of other fields here we had been explicitly setting to
zero, change to first calling memset to clear the struct and then
initialize only the fields that need non-zero default values.
Addresses-Coverity-ID: 467407 ("Uninitialized variables (UNINIT)")
Fixes: 81bd22e935 ("rockchip: block: blk-uclass: add bounce buffer flag to blk_desc")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend the otp driver to read rv1126 otp. This driver code was
adapted from the Rockchip BSP stack.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The following patch migrates the usage of debug and printf functions
to the relevant logging function as per U-Boot DM guidelines.
Additionally some of the debugging statements have been rearanged for
a more meaningfull debug experience.
aarch64-linux-gnu-size reports 229 bytes less when debug is enabled at
file level, while is just 5bytes more when disabled.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@amd.com>
Link: https://lore.kernel.org/r/20231013123739.2757979-1-ibai.erkiaga-elorza@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When 64-bit address is passed only lower 32-bit address
is getting updated. Program the upper 32-bit address in the
DMA destination memory address MSBs register.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011031515.4151-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Unhandled error coming from xilinx_pm_request() but return
value is not read back that's why getting sparse warning
as below:
warning: variable 'ret' set but not used [-Wunused-but-set-variable].
In case of error return the "ret" value.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011025647.17200-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Provide an explicit configuration option to disable default "lock"
of any flash chip which supports locking. By disabling the lock
config will save some amount of memory and also don't expose the
lock functionality to the users i.e., via sf protect command.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The baudrate configured in .config is taken by default by serial. If
change of baudrate is required then the .config needs to changed and
u-boot recompilation is required or the u-boot environment needs to be
updated.
To avoid this, support is added to fetch the baudrate directly from the
device tree file and update.
The serial, prints the log with the configured baudrate in the dtb.
The commit c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for
$fdtfile env variable") is taken as reference for changing the default
environment variable.
The default environment stores the default baudrate value, When default
baudrate and dtb baudrate are not same glitches are seen on the serial.
So, the environment also needs to be updated with the dtb baudrate to
avoid the glitches on the serial.
Also add test to cover this new function.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230921112043.3144726-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration.
Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files
to allow enabling them for armada boards.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921112043.3144726-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmVI8EMACgkQd9zb2sjI
SdG/OA//awml3WYtRnxbEcDn8OWZ7/Pqg5sJ59Szn47/B0M1tO5MgSfT94uux51y
HcSSTC+PqvPNKYFF5ng1sMEzh0byztZxnPBT0YPWUz8glfkMwhke7mycuugXi81M
99Xuj15P7iiMT/W5p6YknzVCvL4ZPFz7Rs7h1n5WoLKadaMOFkR8wa49uOuspjY9
mTj3Z7p/D8DnlDJiF/fK/dU3VQELjy7hbRL+Z8MqGpUAgaNCpX4TReMvnLsTy1NR
PTTNn3OnezjQwjKYaQwy6tYuuLdAHCZ81GDc2uc7Bx5r20CNtTqJCXp9byyZE7fI
Sd8hptAeIw7KCeXciI2IkA6XvDTQpOIbmS07/3BUTPPjzuROppjdLFP+sMPuJ9Yn
hfb3/6VYFAjQ1EhfNPM6mSjNfzxZu5xEmgs072eB4xlNe7nKf2LuxgqghFw/ovED
fXvCxOI79cNrhsvqnOSRB2bhmx0zyXBS664EHi99bDKOBC8oh+sDzsO8s8zbE7Bz
lwyiS0Uxelkd9lRrpKmsv/OWvF5Ii42a/msVIdX5yN7a8w+olll8vdHyrtYacIGU
zkI3BPLLEhOo8WQv4h9W49lMwVDE7GUdNFpborkIh7qW2KU5dhibw5LAmO9HmdOE
9hCiEv34eJwPqx8ydtFD1T3zdcqklPk74hgsDbsHVJQxODaKd1w=
=qtcH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20231106' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- fixup to also enabled DFU RAM boot for libretech-ac
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
One well-known sm child device that provides secure power control is the
Secure Power Controller. This device utilizes SMC calls to communicate
with power domains on the secure monitor side.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231101140500.9025-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
