SMSC911x chips have alignment function to allow frame payload data
(which comes after 14-bytes ethernet header) to be aligned at some
boundary when reading it from fifo (usually - 4 bytes boundary).
This is done by inserting fake zeros bytes BEFORE actual frame data when
reading from SMSC's fifo.
This function controlled by RX_CFG register. There are bits that
represents amount of fake bytes to be inserted.
Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long,
so we need to add 2 fake bytes to get payload data aligned at 4-bytes
boundary.
Linux driver does this by adding IP_ALIGNMENT constant (defined at
skb.h) when calculating fifo data length. All network subsystem of Linux
uses this constant too when calculating different offsets.
But u-boot does not use any packet data alignment, so we don't need to
add anything when calculating fifo data length.
Moreover, driver zeros the RX_CFG register just one line up, so chip
does not insert any fake data at the beginig. So calculated data length
is always bigger by 1 word.
It seems that at almost every packet read we get an underflow condition
at fifo and possible corruption of data. Especially at continuous
transfers, such as tftp.
Just after removing this magic addition, I've got tftp transfer speed as
it aught to be at 100Mbps. It was really slow before.
It seems that fifo underflow occurs only when using byte packing on
32-bit blackfin bus (may be because of very small delay between reads).
Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Cosmetic changes: Few comments updated
Functionality: Rx packet frame size is programming should
be done when port is in disabled state. this is corrected
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Fix MX27 FEC logic to check validity of the MAC address in fuse.
Only null (empty fuse) or invalid MAC address was retrieved from mx27 fuses before this change.
Signed-off-by: Eric Jarrige <jorasse@armadeus.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped. We need to wait for both, or the
controller could get into an invalid state.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current dm9000x driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
Blackfin systems as the accesses can get out of order. So convert the
direct volatile dereferences to use the normal in/out macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This saves the autonegotation delay when not using ethernet in U-Boot
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Avoid using the internal eeprom on MX25 like MX51 already does.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch enabled support for having PHYs on bitBang MII and uec MII
operating at the same time. Modeled after the MPC8360ADS implementation.
Added the ability to specify which ethernet interfaces have bitbang SMI
on the board header file.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
For some reason, (which I can't find any documentation on), if U-Boot
gives a port number higher than 17500 to a Microsoft DNS server, the
server will reply to port 17500, and U-Boot will ignore things (since
that isn't the port it asked the DNS server to reply to).
This fixes that by ensuring the random port number is less than 17500.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
For code archeologists, this is a nice example of copy and paste history.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch fixes following build warnings for kirkwood_egiga.c
kirkwood_egiga.c: In function "kwgbe_init":
kirkwood_egiga.c:448: warning: dereferencing type-punned pointer will break strict-aliasing rules
kirkwood_egiga.c: In function "kwgbe_recv":
kirkwood_egiga.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
QONG is a module that can be installed on several boards,
not only on the QONG-EVB manufactured by Dave srl.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The QONG module can be downsized and delivered
with 128MB instead of 256MB. The patch adds
run time support for the two different memory
configurations.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The NAND device is connected to the FPGA of the QONG board
and not to the NFC controller. For this reason, the FPGA must
be set and initialized before accessing to the NAND itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Replace call to imx_get_mpllclk with imx_get_armclk
to show frequency of ARM core instead of mpll internal
bus in print_cpuinfo.
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
moved CONFIG_CMD_FAT to filesystem section
swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
This patch includes a few additional commands in the sheevaplug
version of u-boot:
- support for LONGHELP so you can get help messages
- auto completion and command editing
- ubi and mii support
- ext2 filesystem (convenient if you have an ext2 from which you want to boot)
- jffs2 and ubifs filesystems (if you want to use these in NAND)
This also makes it more similar to openrd client.
Side effect of this patch is that the code now needs 3 sectors i.s.o. 2
so an existing env is overwritten
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
The lowlevel_init file contained some hard-coded values
to setup the RAM. These board related values are moved into
the board configuration file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch adds support for the magnesium board from
projectiondesign. This board uses i.MX27 SoC and has
8MB NOR flash, 128MB NAND flash, FEC ethernet controller
integrated into i.MX27. As this port is based on
the imx27lite port, common config options are collected
in include/configs/imx27lite-common.h
Signed-off-by: Heiko Schocher <hs@denx.de>
Because of s5pc1xx gpio is same as s5p seires SoC,
move gpio functions to drvier/gpio/
and modify structure's name from s5pc1xx_ to s5p_.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch fixes APC405 build, by defining CONFIG_PPC4XX_I2C. This is
needed since the move of the PPC4xx I2C driver into the drivers/i2c
directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
This patch adds support for the Mosaix Technologies, Inc. ICON board,
based on the AppliedMicro (AMCC) PPC440SPe. It's equipped with an SODIMM
(512MB standard) and 64MByte of NOR FLASH.
Support for the onboard SM502 will be added later.
Signed-off-by: Stefan Roese <sr@denx.de>
