Merge 'spare' into 'bootloader' partition
Use same partition for ramdisk and rootfs boot scenarios.
Remove 'ramdisk' partition, use 'rootfs' for ramdisk
(ramdisk and nand boot scenarios are mutually exclusive).
Expand last partition to end of actual NAND size.
Adjust UBIFS rootfs boot kernel arguments.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
>From TO1.1, SNVS adds internal pull up control for POR_B,
the register filed is GPBIT[1:0], after system boot up,
it can be set to 2b'01 to disable internal pull up.
It can save about 30uA power in SNVS mode.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
For i.MX6, the mux width is 4, not 3. So enlarge the width.
IOMUX_CONFIG_LPSR is changed from 0x8 to 0x20 to not use bit 3 of mux.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Currently the bmode "usb" uses BOOT_CFG1 to 0x01, -which means
BOOT_CFG1[7:4] is set to b0000. According to Table 8-7 Boot
Device Selection this is NOR/OneNAND and not Reserved.
Use 0x10 which leads to b0001, which is a Reserved boot device.
With that the SoC reliably falls back to the serial loader.
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Need to initialize mmc->dev when probe, or will met
"dev_get_uclass_priv: null device", when `mmc dev 1`.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add i.mx6ul clock header, copied from kernel commit (29b4817d401).
i.MX6ULL reuse the file in Linux Kernel, so let's keep the same.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Add pinctrl defines for NXP i.MX 6ULL.
Since i.MX6ULL reuses some definitions of i.MX6UL,
also add i.MX6UL pinctrl defines from linux kernel commit (29b4817d401).
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
There two iomuxc for i.MX6ULL. one iomuxc is compatible is i.MX6UL,
the other iomuxc is for SVNS usage, similar with the one in mx7.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module,
not in IOMUXC, so correct the related registers' offset.
Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate
them from iomuxc pins.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since the mx6ull adds the AIPS3, so enable its initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update memory map address for mx6ull.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update Clock settings and CCM register map for i.MX6ULL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update misc SOC related settings for i.MX6ULL, such as FEC mac address,
cpu speed grading and mmdc channel mask clearing.
Also update s_init to skip pfd reset.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since MX6ULL select MX6UL, we can not use IS_ENABLED(CONFIG_MX6UL) here,
because this piece code is only for i.MX6UL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rom already initialized clock at 396M and 132M for arm core and ahb,
so skip setting them again in U-Boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX6ULL has two 128 bits fuse banks, bank 7 and bank 8,
while other banks use 256 bits. So we have to adjust the
word and bank index when accessing the bank 8.
When in command line `fuse read 8 0 1`, you can image
`fuse read 7 4 1` in the ocotp driver implementation for 6ULL.
When programming, we use word index, so need to fix bank7/8 programming
for i.mx6ull.
For example: fuse prog 8 3 1; The word index is (8 << 3 | 3) --> 67.
But actully it should be (7 << 3 | 7) ---> 63.
So fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX6ULL major cpu type.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
There is no stable mmcblk device numbering over different linux versions.
Enable CMD_PART to be able to query the UUID of the root filesystem partition.
So we can pass root=PARTUUID=XXX instead of root=/dev/mmcblkXpY in bootargs.
Leave the default environment as is for now to stay compatible with original
TBS settings.
Signed-off-by: Soeren Moch <smoch@web.de>
Currently the driver asserts WDOG_B by clearing WCR_WDA bit when
enabling the watchdog. Do not clear WCR_WDA.
Signed-off-by: Ross Parker <rossjparker@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
The CPU detection macro is_mx6dq returns 0 on an i.MX6DQP, so we need to
check for it explicitly in order to correctly initialize the pads when
CONFIG_MX6QDL is defined.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
The linux kernel imx_v6_v7_defconfig sets the user/kernel memory split
to 3G/1G now (was 2G/2G before). We have to adapt the BOOTMAPSZ so that
the decompressor finds zImage and dtb in lowmem.
Signed-off-by: Soeren Moch <smoch@web.de>
When using SPL on i.mx6 we frequently notice some DDR initialization
mismatches between the SPL code and the non-SPL code.
This causes stability issues like the ones reported at 7dbda25ecd
("mx6ul_14x14_evk: Pass refsel and refr fields to avoid hang") and also:
http://lists.denx.de/pipermail/u-boot/2016-September/266355.html .
As the non-SPL code have been tested for long time and proves to be reliable,
let's configure the DDR in the exact same way as the non-SPL case.
The idea is simple: just use the DCD table and write directly to the DDR
registers.
Retrieved the DCD tables from:
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg
and
board/freescale/mx6sabresd/mx6qp.cfg
(NXP U-Boot branch imx_v2015.04_4.1.15_1.0.0_ga)
This method makes it easier for people converting from non-SPL to SPL code.
Other benefit is that the SPL binary size is reduced from 44 kB to 39.9 kB.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The videoargs script is kernel version dependent and since wandboard
uses distro config, there is no need to handle videoargs locally.
In case such video related settings are needed, then the proper
location would be the distro extlinux.conf or boot.scr files.
So remove 'videoargs' script.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
A kernel hang is observed when running wandboard 3.14 kernel and
going to the lowest operational point of cpufreq:
# ifconfig eth0 down
# echo 1 > /sys/class/graphics/fb0/blank
The problem is caused by incorrect setting of the REFR field
of register MDREF. Setting it to 4 refresh commands per refresh
cycle fixes the hang.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Authentication of images in Falcon Mode is not supported. Do not enable
SPL_OS_BOOT when TI_SECURE_DEVICE is enabled. This prevents attempting
to directly load kernel images which will fail, for security reasons,
on HS devices, the board is locked if a non-authenticatable image load
is attempted, so we disable attempting Falcon Mode.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
This config option seems to be unused and is probably vestigial.
Remove it.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Like OMAP54xx and AM43xx family SoCs, AM33xx based SoCs have high
security enabled models. Allow AM33xx devices to be built with
HS Device Type Support.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
When CONFIG_FIT_IMAGE_POST_PROCESS or CONFIG_SPL_FIT_IMAGE_POST_PROCESS
is enabled board_fit_image_post_process will be called, add this
function to am33xx boards when CONFIG_TI_SECURE_DEVICE is set to
verify the loaded image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
The option SPL_SPI_SUPPORT is used to enable support in SPL for loading
images from SPI flash, it should not be used to determine the build type
of the SPL image itself. The ability to read images from SPI flash does
not imply the SPL will be booted from SPI flash.
Unconditionally build SPI flash compatible SPL images.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a section describing the additional boot types used on AM33xx
secure devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes.
For AM33xx devices additional image types are needed for
various SPL boot modes as the ROM checks for the name of
the boot mode in the file it loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.
This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by the
CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE config option.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the ending portion of the DRAM is reserved for secure
world use, then u-boot cannot use this memory for its relocation
purposes. To prevent issues, we mark this memory as PRAM and this
prevents it from being used by u-boot at all.
Signed-off-by: Daniel Allred <d-allred@ti.com>
After EMIF DRAM is configured, but before it is used,
calls are made on secure devices to reserve any configured
memory region needed by the secure world and then to lock the
EMIF firewall configuration. If any other firewall
configuration needs to be applied, it must happen before the
lock call.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a secure OS/TEE). There are two sizes, a total size and a
protected size. The region is divided into protected (secure) and
unprotected (public) regions, that are contiguous and start at the
start address given. If the start address is zero, the intention
is that the region will be automatically placed at the end of the
available external DRAM space.
Signed-off-by: Daniel Allred <d-allred@ti.com>
rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.
We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>