Adds an "ncsi" command to manually start NC-SI configuration.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
In the sbi command use the same short texts for the legacy extensions
as the SBI specification 1.0.0.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
If calling 'Get SBI specification version' fails, write an error message
and return CMD_RET_FAILURE.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The SBI command can print out the version number of the SBI implementation.
Choose the correct output format for RustSBI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Some configuration symbols formerly defined in header files were
recently converted to Kconfig symbols. This moved their value definition
into *every* defconfig file, even though those values are hardly board
choices.
Use the new Kconfig option to define per-SoC default values, in just one
place, which makes the definition in each defconfig file redundant.
We refrain from setting a sunxi specific value for CONFIG_SYS_BOOTM_LEN,
so this defaults to a much better 64MB for uncompressed arm64 kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The working FDT is the one which comes from the OS and is fixed up by
U-Boot. When the bootm command runs, it sets up the working FDT to be the
one it is about to pass to the OS, so that fixups can happen.
This seems like an important step, so add a message indicating that the
working FDT has changed. This is shown during the running of the bootm
command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Functions which implement commands must return a CMD_RET_... error code.
At present bootm can return a negative errno value in some cases, thus
causing strange behaviour such as trying to exit the shell and printing
usage information.
Fix this by returning the correct value.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a few commands that iterate uclass with
uclass_first_device/uclass_next_device or the _err variant.
Use the _check class iterator variant to get devices that fail to probe
as well, and print the status.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Loadfile2 code is installing two protocols on it's own handle
and uses efi_delete_handle() to clean it up on failure(s). However
commit 05c4c9e21a ("efi_loader: define internal implementations of
install/uninstallmultiple") prepares the ground for us to clean up
efi_delete_handle() used in favor of Install/UninstallMultipleProtocol.
While at it clean up the non needed void casts to (void *) on the
protolcol installation.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* don't use EFI_CALL() for variable services
* don't use runtime pointer to access exported function
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
To allow easily iterate over all UBI volumes, add a new command which
either print all user UBI volumes on output or set them into env variable.
As UBI volumes can have arbitrary name/label, in most cases it is useful to
iterate them by their numbers. This can be achieved by -numeric flag.
This functionality is similar to already existing 'part list' command which
prints partitions on formatted block device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Currently, there is no way for users to check the readings from thermal
sensors from U-boot console, only some boards print it during boot.
So, lets add a simple "temperature" command that allows listing thermal
uclass devices and getting their value.
Note that the thermal devices are intenionally probed if list is used as
almost always they will not get probed otherwise and there is no way for
users to manually call probe on a certain device from console.
Assumption is made that temperature is returned in degrees C and not
milidegrees like in Linux as this is what most drivers seem to return.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add xxd command to print file content as hexdump to standard out
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Roger Knecht <rknecht@pm.me>
When host issues "fastboot reboot fastboot", it's expected that the
board drops the USB connection before resetting.
On some boards, such as Khadas VIM3L and SEI610, this is not the case.
We observe the following error:
$ fastboot reboot fastboot
Rebooting into fastboot OKAY [ 0.004s]
fastboot: error: Failed to boot into userspace fastboot; one or more components might be unbootable.
This does not happen when we use the RST button on the board.
It can be reproduced in linux with:
# echo b > /proc/sysrq-trigger
In this case, we hit a undefined hardware behavior, where D+ and D-
are in an unknown state. Therefore the host can't detect usb
disconnection.
Make sure we always call usb_gadget_release() when a "fastboot reboot"
command is issued.
Note: usb_gadget_release() should be called before g_dnl_unregister()
because g_dnl_unregister() triggers a complete() call on each
endpoint (thus calling do_reset()).
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The cls command works fine on the serial console. There is no reason to
let it depend on the availability of video.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In general handles should only be deleted if the last remaining protocol
is removed. Instead of explicitly calling
efi_create_handle -> efi_add_protocol -> efi_delete_handle which blindly
removes all protocols from a handle before removing it, use
InstallMultiple/UninstallMultiple which adheres to the EFI spec and only
deletes a handle if there are no additional protocols present
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently we have subcommands 'efidebug dh' which shows protocols per
handle and 'efidebug devices' which shows the device path. None shows which
U-Boot device matches the handle.
Change 'efidebug dh' to show the device path and the U-Boot device if any
is associated with the handle.
Remove 'efidebug devices'.
Old output of 'efidebug dh':
Handle Protocols
================ ====================
000000001b22e690 Device Path, Block IO
000000001b22e800 Device Path, Block IO, system, Simple File System
New output of 'efidebug dh':
000000001b22e690 (host0)
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/VenHw(bbe4e671-5773-4ea1-9aab-3a7dbf40c482,00)
Block IO
000000001b22e800 (host0:1)
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/VenHw(bbe4e671-5773-4ea1-9aab-3a7dbf40c482,00)/HD(1,GPT,7e5c17c5-3f5f-49d0-ae96-511b21d7f273,0x800,0x3f7df)
Block IO
system
Simple File System
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a lot of cases kernel resets UART HW. To ensure that U-Boot messages
printed before booting the kernel are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changing baudrate is a sensitive operation. To ensure that U-Boot messages
printed before changing baudrate are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt command currently handles stringlists as strings in 'fdt get value'
subcommand. Since strings in FDT stringlists are separated by '\0', only
the first value gets inserted into the environment variable passed to the
'fdt get value' command.
Example, consider the following DT snippet:
/ { compatible = "foo", "bar" };
The following command only reports the first string in stringlist:
=> fdt get value var / compatible ; print var
foo
It is not possible to assign list of null-terminated strings into U-Boot
environment variable. Add optional 'index' parameter to the subcommand
'fdt get value <var> <path> <prop> [<index>]' which lets user specify which
string within the stringlist should be assigned into the 'var' variable.
The default value of 'index' is 0 in case it is not present. This way the
'fdt' command API does not change and existing scripts are not broken.
The following command now reports the Nth string in stringlist, counting
from zero:
=> fdt get value var / compatible 1 ; print var
bar
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This condition is not needed for these commands, since BLK is enabled for
all boards which use block devices and commands are not available in SPL,
so even if SPL_BLK is not enabled, it doesn't affect commands.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now when loadx and loady commands could be aborted / cancelled by CTRL+C,
allow to configure timeout for initial x/y-modem packet via env variable
$loadxy_timeout and by default use value from new compile-time config
option CONFIG_CMD_LOADXY_TIMEOUT. Value is in seconds and zero value means
infinite timeout. Default value is 90s which is the value used before this
change for loadx command.
Other load commands loadb and loads already waits infinitely. Same behavior
for loadx and loady commands can be achieved by setting $loadxy_timeout or
CONFIG_CMD_LOADXY_TIMEOUT to 0.
Signed-off-by: Pali Rohár <pali@kernel.org>
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
-----BEGIN PGP SIGNATURE-----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=P89S
-----END PGP SIGNATURE-----
Merge tag 'efi-next-2022-09-14' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for efi next
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
This commit adds the menu entry to update UEFI BootOrder variable.
User moves the entry with UP/DOWN key, changes the order
with PLUS/MINUS key, press SPACE to activate or deactivate
the entry, then finalizes the order by ENTER key.
If the entry is activated, the boot index is added into the
BootOrder variable in the order of the list.
The U-Boot menu framework is well designed for static menu,
this commit implements the own menu display and key handling
for dynamically change the order of menu entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
UEFI specification requires booting from removal media using
a architecture-specific default image name such as BOOTAA64.EFI.
This commit adds the removable media entries into bootmenu,
so that user can select the removable media and boot with
default image.
The bootmenu automatically enumerates the possible bootable
media devices supporting EFI_SIMPLE_FILE_SYSTEM_PROTOCOL,
add it as new UEFI boot option(BOOT####) and update BootOrder
variable. This automatically generated UEFI boot option
has the dedicated guid in the optional_data to distinguish it from
the UEFI boot option user adds manually. This optional_data is
removed when the efi bootmgr loads the selected UEFI boot option.
This commit also provides the BOOT#### variable maintenance feature.
Depending on the system hardware setup, some devices
may not exist at a later system boot, so bootmenu checks the
available device in each bootmenu invocation and automatically
removes the BOOT#### variable corrensponding to the non-existent
media device.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit adds the menu entry to delete the UEFI boot option.
User moves the entry with UP/DOWN key, changes, then presses
ENTER key to delete the selected boot option.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit adds the menu entry to edit the existing
BOOT#### variable contents.
User selects the item from the boot option list, then
user can edit the description, file path and optional_data.
Note that automatically generated boot option entry by bootmenu
to support the removable media device is filtered out and user
can not edit the automatically generated entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit add the "eficonfig" command.
The "eficonfig" command implements the menu-driven UEFI boot option
maintenance feature. This commit implements the addition of
new boot option. User can select the block device volume having
efi_simple_file_system_protocol and select the file corresponding
to the Boot#### variable. User can also enter the description and
optional_data of the BOOT#### variable in utf8.
This commit adds "include/efi_config.h", it contains the common
definition to be used from other menus such as UEFI Secure Boot
key management.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This patch adds the cyclic command, which currently only supports the
'list' subcommand, to list all currently registered cyclic functions.
Here an example:
=> cyclic list
function: cyclic_demo, cpu-time: 7010 us, frequency: 99.80 times/s
function: cyclic_demo2, cpu-time: 1 us, frequency: 1.13 times/s
As you can see, the cpu-time is accounted, so that cyclic functions
that take too long might be discovered. Additionally the frequency is
logged.
The 'cyclic demo' commands registers the cyclic_demo() function to
be executed all 'cycletime_ms' milliseconds. The only thing this
function does is delaying by 'delay_us' microseconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add bdinfo_print_size() helper to display size variables (such as cache
sizes) in bdinfo format. The size is printed as "xxx Bytes", "xxx KiB",
"xxx MiB", "xxx GiB", etc as needed;
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
For obvious reasons BootROMS rejects unsigned images when secure boot is
enabled in OTP secure bits. So check for OPT secure bits and do not allow
flashing unsigned images when secure boot is enabled. Access to OTP via
U-Boot fuse API is currently implemented only for A38x and A37xx SoCs.
Additionally Armada 3700 BootROM rejects signed trusted image when secure
boot is not enabled in OTP. So add also check for this case. On the other
hand Armada 38x BootROM acceps images with secure boot header when secure
boot is not enabled in OTP.
OTP secure bits may have burned also boot device source. Check it also and
reject flashing images to target storage which does not match OTP.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently for A38x image is checked only header checksum.
So check also for image data checksum to prevent flashing broken image.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The command's name is a misnomer.
The command loads a file but does not run (boot) it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Calling tftpput with less than 2 arguments must lead to a failure.
If tftpput is called with two arguments, these are the address and
the size of the file to be transferred.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the FIT loading process of the fpga command to use
fit_get_data_node.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Format the KVM implementation number in a human readable form.
With the patch output of the sbi command for Linux 5.19.1 looks like:
=> sbi
SBI 0.3
KVM 5.19.1
Machine:
Vendor ID 0
Architecture ID 7005c
Implementation ID 7005c
Extensions:
SBI Base Functionality
Timer Extension
IPI Extension
RFENCE Extension
Hart State Management Extension
System Reset Extension
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
It is useful to read information about the current TPM state, where
supported, e.g. for debugging purposes when verified boot fails.
Add support for this to the TPM interface as well as Cr50. Add a simple
sandbox test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This feature is used for measured boot, so we can add a log entry to the
TCPA with some information about where the digest comes from. It is not
currently supported in the TPM drivers, but add it to the API so that
code which expects it can signal its request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
fit_image_get_comp() should not set value -1 in case it can't read
the compression node. Instead, leave the value untouched in that case
as it can be absent and a default value previously defined by the
caller of fit_image_get_comp() should be used.
As a result the warning message
WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its file!
no longer shows if the compression node is actually absent.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reinstates fix from commit 8f8c04bf1e ("i2c: fix stack buffer
overflow vulnerability in i2c md command") without the changes unrelated
to the actual fix. Avoid the underflow by setting only nbytes and
linebytes as unsigned integers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nicolas Iooss <nicolas.iooss+uboot@ledger.fr>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
This reverts commit 8f8c04bf1e.
The commit is largely wrong and breaks most of i2c command functionality.
The problem described in the aforementioned commit commit message is valid,
however the commit itself does many more changes unrelated to fixing that
one problem it describes. Those extra changes, namely the handling of i2c
device address length as unsigned instead of signed integer, breaks the
expectation that address length may be negative value. The negative value
is used by DM to indicate that address length of device does not change.
The actual bug documented in commit 8f8c04bf1e
can be fixed by extra sanitization in separate patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nicolas Iooss <nicolas.iooss+uboot@ledger.fr>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
other minor fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmMJZZ8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZ8pggAjYxdCTEtTMJamt67hht8xjeZLom4KX3G
HZJhXHAXHgnw2vku4nYKEZp6B5+if184I34Gbw6AGHJib7tfGBPFHeb0lIg+NHlB
bb7hMSKJwZJAASWB5Txqtmx2iFdnTZVnUUMp5Jl8Fpd0yhd8YxsaDKrt7BUTTZgM
84ht/zv+laFoDvM0Xj81TVkPym8ShIylsUc44Sn8je5KC8kg1lmukqnBHAOj0DKG
cE/hGOmdq5HLu7Ylj3XQ8tl6jpPMn6hltoIMku6ePsJeaTOdsXg2i3RN/Xga835D
7/KW+qasl2+5XwqYyAXjLW6YncbGzxmsLfJ6HrzInLtp9rkOt/z0hA==
=09Bs
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26aug22' of https://source.denx.de/u-boot/custodians/u-boot-dm
binman/patman documentation improvements
other minor fixes
Avoid enabling this command by default. This saves about 1KB of code
space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
PCIe config space has address range 0-4095. So do not allow reading from
addresses outside of this range. Lot of U-Boot drivers do not expect that
passed value is not in this range. PCI DM read function is extended to
fill read value to all ones or zeros when it fails as U-Boot callers
ignores return value.
Calling U-Boot command 'pci display.b 0.0.0 0 0x2000' now stops printing
config space at the end (before 0x1000 address).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently message is not intended that prompt end up at the end of debug
line. For example like this:
DFU alt info setting: done
DFU entities configuration failed!
(partition table does not match dfu_alt_info?)
Firmware update failed: <NULL>
Cannot handle a capsule at 10000000Zynq>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for handling this concept in bootflows. Update the 'bootflow'
command to allow only the normal bootmeths to be used. This alllows
skipping EFI bootmgr and VBE, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
With global bootmeths we want to scan without a bootdev. Update the logic
to allow this.
Change the bootflow command to show the bootdev only when valid.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current way of handling things like EFI bootmgr is a bit odd, since
that bootmeth handles selection of the bootdev itself. VBE needs to work
the same way, so we should support it properly.
Add a flag that indicates that the bootmeth is global, rather than being
invoked on each bootdev. Provide a helper to read a bootflow from the
bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the dependency on CMD_PXE from BOOTMETH_DISTRO by introducing a
new hidden kconfig symbol to control whether pxe_utils is compiled,
allowing bootstd's distro method to be compiled without needing
networking support enabled.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct build errors when CMD_BOOTM is not enabled:
Signed-off-by: Simon Glass <sjg@chromium.org>
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
If 'extension apply all' is executed and no extension is found, the return
value of do_extension_apply() is undefined. Return CMD_RET_FAILURE in this
case.
Fixes: 2f84e9cf06 ("cmd: add support for a new "extension" command")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
The source code contains an error:
- argv[2] contains <channel> arg, variable for env_set is in argv[3]
- number of args is 4
Revert 54d24d7260
cmd: simplify do_adc_single()
Fixes 9de612ae4d
cmd: adc: Add support for storing ADC result in env variable
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'rng' command dumps a number of random bytes on the console. Add a
set of tests for the 'rng' command. The test function performs basic
sanity testing of the command.
Since a unit test is being added for the command, enable it by default
in the sandbox platforms.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use a statically allocated buffer on stack instead of using malloc for
reading the random bytes. Using a local array is faster than
allocating heap memory on every initiation of the command.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The 'rng' u-boot command is used for printing a select number of
random bytes on the console. Currently, the RNG device from which the
random bytes are read is fixed. However, a platform can have multiple
RNG devices, one example being qemu, which has a virtio RNG device and
the RNG pseudo device through the TPM chip.
Extend the 'rng' command so that the user can provide the RNG device
number from which the random bytes are to be read. This will be the
device index under the RNG uclass.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Negative return value from cmd main function cause U-Boot to print criplic
error message: exit not allowed from main input shell.
Set return value on error to 1.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Armada 3700 BootROM supports also images with sha512 checksums and
mox-imager tool [1] generates such bootable images. Without sha512 support
U-Boot bubt command just prints error message:
Error: Unsupported hash_algorithm_id = 64
Error: Image header verification failed
This patch adds support for sha512 checksum validation for Armada 3700
images. With it bubt prints:
Image checksum...OK!
[1] - https://gitlab.nic.cz/turris/mox-boot-builder.git
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
net_loop() returns signed int type and negative value represents error.
tftp_read_file() returns unsigned size_t type and zero value represents
error. Casting signed negative value to unsigned size_t type cause losing
information about error and bubt thinks that no error happened, and
continue erasing SPI-NOR which cause malfunction device.
Fix this issue by correctly propagating failure during tftp transport.
With this change when there is no eth link, bubt does not erase SPI-NOR
anymore.
=> bubt
Burning U-Boot image "flash-image.bin" from "tftp" to "spi"
ethernet@30000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
ethernet@30000: No link.
Error: Failed to read file flash-image.bin from tftp
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Current image type verification code is specific to 32-bit Armada SoCs but
used only for Armada 38x. Implement image type verification for Armada 3700
and enable Armada 38x image verification for all 32-bit Armada SoCs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
add arguments for mmc wp to assign which boot partition to protect.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
These flags may be used to check whether an FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-7-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
It allows using this feature without enabling the "fpga loads"
command.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Co-developed-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-2-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Do not suggest successful operation if a flash area to be changed is
actually locked, thus will not execute the request. Rather report an
error and bail out. That's way more user-friendly than asking them to
manually check for this case.
Derived from original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
efi_dp_str() allocates memory which should be released after use.
Use %pD printf code. Adjust message wording.
Fixes: d837cb1e3b ("efi: Add debugging to efi_set_bootdev()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The "autoload" environment variable is always checked with env_get_yesno
as it can be set to any form of no. The default behavior of
env_get_yesno is to return -1 on variables that are not set, which acts
as true in general (we test for non-zero return). To convert
CONFIG_SYS_AUTOLOAD to Kconfig, given that it was almost always used to
set autoload to no, first rename to CONFIG_SYS_DISABLE_AUTOLOAD for
consistency sake. Then, make it so that if enabled we set autoload=0 in
the default environment. Migrate all platforms which set
CONFIG_SYS_AUTOLOAD to non-true or that set autoload to false in their
default environment to using CONFIG_SYS_DISABLE_AUTOLOAD
Signed-off-by: Tom Rini <trini@konsulko.com>
