The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Support for Raydium RM68200 720p dsi 2dl video mode panel.
This rm68200 panel driver is based on the Linux Kernel driver from
drivers/gpu/drm/panel/panel-raydium-rm68200.c.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Add a Synopsys Designware MIPI DSI host bridge driver, based on the
Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
This also enables mtd configs which are required by nandbcb command.
This command would be used to configure boot control block(BCB) while
writing spl image on nand device.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Implementation of pmic_get() uses uclass_find_device_by_name(), which
behaviour was changed in 4213609cc7
("drivers: core: use strcmp when find device by name"). Now we have to
supply full node name with unit address.
Fixes boot issue:
U-Boot 2019.07-00788-g0ef6e69a1e-dirty (Jul 19 2019 - 15:27:02 +0300)
CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 41C
Reset cause: POR
DRAM: 512 MiB
initcall sequence 9ffd3a4c failed at call 87803c61 (err=-19)
ERROR Please RESET the board
Fixes: 4213609cc7("drivers: core: use strcmp when find device by name")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
When building a FIT image for SPL to load also take into account the
configured external offset. This allows the SPL to load the u-boot FIT
image correctly when configuring SECURE_BOOT on i.mx6 is enabled
(with CONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Note this doesn't allow secure booting; but it does allow an unsigned
SPL/u-boot with secure boot support eanbled to boot on open device.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Modify the SPL TEXT base from OCRAM alias to OCRAM base 0x100000, so
we can use full OCRAM not limit to 96KB
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch updates envs responsible for using USB pendrive as a
SWUpdate based tool for recovery and update.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds new file - imx6q-kp-u-boot.dtsi with a set of u-boot
specific properties for imx6q KP device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The TPC70 can boot from SD card (debug/development) and eMMC (production).
The board_boot_order() function provides a run time check for the device
from which one wants to boot (it is selected by GPIO pins setup).
Moreover, a fallback to SD card is provided if the detection is not
possible or working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.
This patch removes the legacy pinmuxing code from the board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since this board config only supports, the i.MX6D/i.MX6Q configurations,
256K of on-chip RAM is available which increases the space available
to SPL to help further reduce board code and further enable device tree
functions.
This patch enables 256K of RAM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
So we can get rid of legacy pci config code.
PCI_PNP is not required for this board, remove it to reduce the size of the
u-boot binary.
DM_PCI does not start the host controller automatically anymore. Do so
in preboot instead.
Signed-off-by: Soeren Moch <smoch@web.de>
Both the distro boot configuration as well as the general pxe support
standardized on fdtfile as the variable to hold the dtb filename.
Adjust to follow that such that e.g. "pxe boot" will just work.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.htmlhttps://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Mipi_display.c contains a set of dsi helpers.
This file is a copy of file drm_mipi_dsi.c (linux kernel).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
We don't need to pull in anything from the MIPS job so exclude that from
the new bcm job and make it clear it's building only ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
When hitting an invalid FAT cluster while reading a file always print an
error message and return an error code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
