Do not use 0 as address for memory because of the special meaning for
pointers (null pointer). Change the spl bss start address to the second
page.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220714134733.7487-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The ISW_ENTRY_ADDR symbol was used for OMAP devices in place of
SPL_TEXT_BASE. Keystone2 HS devices were not using it right either.
Remove ISW_ENTRY_ADDR and use SPL_TEXT_BASE directly.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
CONFIG_PREBOOT just cause putting "preboot=CONFIG_PREBOOT" into env list.
Value CONFIG_PREBOOT="run preboot" in defconfig is just nonsense and does
not do anything useful (it is infinite recursion). Config file for this
board already contains default preboot= env variable with correct value,
which has higher priority than CONFIG_PREBOOT and this is reason why
nonsense CONFIG_PREBOOT is ignored.
Remove nonsense and unused CONFIG_PREBOOT from nokia_rx51_defconfig file.
Signed-off-by: Pali Rohár <pali@kernel.org>
We have different dtbs for the Lite and Extended WiFi variants of the
SanCloud BBE.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_ETHPRIME can be set to DT node name or alias which refers to DT
node. Define ethernet aliases and set ETHPRIME to eth2 which refers to WAN
ethernet port. This removes hardcoded DT node name from U-Boot
configuration file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
uDPU like eDPU does not expose SCSI based peripherals like SATA nor PCI
and for sure it does not have the Intel E1000 PCI card.
So, like for eDPU remove those from the defconfig.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
eDPU does not use SCSI nor it has SATA exposed, and commit
arm: mvebu: a3720: Set BOOT_TARGET_DEVICES list to enabled peripherals
now allows compiling U-boot wihout all of the BOOT_TARGET_DEVICES since
not all boards have all of the listed peripherals exposed.
So, disable SCSI support in defconfig for eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Methode eDPU is an Armada 3720 power board based on the Methode uDPU.
They feature the same CPU, RAM, and storage as well as the form factor.
However, eDPU only has one SFP slot plus a copper G.hn port which does not
work under U-boot.
In order to reduce duplication, split the uDPU DTS into a common one.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables the recently added watchdog support on the MIPS
Octeon EBB7304 eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The boards that come with a flash memory pre-soldered have a Macronix
flash chip.
Fixes: 280294c5df ("sunxi: boards: Enable SPI flash support in U-Boot proper")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Many LicheePi Nano boards come with SPI flash soldered, which already
works for booting the SPL and loading U-Boot proper.
With the updated DTB, we can now also use the SPI flash from U-Boot
proper, so enable the bits in the defconfig, to allow loading binaries
from SPI flash.
There seem to be board revisions with a Winbond SPI chip, but also
others with an XTX chip, so include support for both: the actual chip
used will be autodetected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Adding the SPL_USB_DWC3_GENERIC symbol broke some ti builds. This
should fix the builds but untested on HW.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
The mt7621_rfb board supports integrated giga PHYs plus one external
giga PHYs. It also has up to 512MiB DDR3, 16MB SPI-NOR, 3 mini PCI-e x1
slots, SDXC and USB.
The mt7621_nand_rfb board is almost the same as mt7621_rfb board, but it
uses NAND flash and SDXC is not available.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmLNj88ACgkQ4rK92eCq
k3Wukwf+PZnmQuyzwwFDOpZO1lUPfUN0WkoEBV8M5IxLehHdfHJT3YsAtm6DS8dd
4+n0+WmR7Uk4B8ODRPrGNBJftFoOVfEAvWmpfCC/VcHgEDEzdJzJe6yxa9wAWeQR
djRZLM8qx6OIEUW+sfYbFkD2BCv+cLiT0YH9qqx8WCRlf6JTuLquSBJQXIJAqYiE
LdO/pp0rv4oC0s08BSL4bHL/Mh7FHeUPiEjn2uRP/vISgmH1qyCql3gbr/wCaTYR
jfqr9pjmWTxEOppZIdE832QMy1MTSA/6Q3Jr4LKRko6ArBGjbGlj3EbeeEdKPDRy
BtQ6OLnxWKdcPr2qp301nnERRi4L4w==
=WgbW
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220712' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Alignment with Linux kernel device tree v5.19 for stm32mp15 and stm32mp13
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
MPS3 board have a ISP1763 usb controller, enable it to be used
for mass storage access for example. Enable the usb command
also and for the FVP support for mass storage enable the mmc
command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Activate the I2C driver in STM32MP13x config.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the RTC driver in STM32MP13x config.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the RNG driver provided by OP-TEE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With support of SCMI in OP-TEE, the early malloc usage
increase, the associated defined CONFIG_SYS_MALLOC_F_LEN
need to be increased.
For example, for stm32mp15_defconfig and
stm32mp157c-dk2-scmi.dtsi, we have:
Early malloc usage: 14098 / 80000
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Perform a basic migration of the calls in setup_serial_number() to DM so
that we can switch to using DM_I2C on this platform.
Cc: David Lechner <david@lechnology.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: David Lechner <david@lechnology.com>
Currently, the imx8mq_phanbell board fails to boot.
Remove the custom CONFIG_SYS_MALLOC_F_LEN setting in favor of the
generic one done via the main Kconfig.
Since commit b598957206 ("Kconfig: Fix SYS_MALLOC_F_LEN for i.MX8MQ")
the default SYS_MALLOC_F_LEN value for i.MX8MQ is 0x2000.
With such default value, the board boots again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The normal way of loading u-boot is as a FIT, so configure u-boot.img as
the SPL playload.
The u-boot-with-spl.bin target will add padding according to
CONFIG_SPL_MAX_SIZE which defaults to 64KB on the AST2600.
With this the following simple steps can be used to build and boot a
system:
make u-boot-with-spl.bin
truncate -s 64M u-boot-with-spl.bin
qemu-system-arm -nographic -M ast2600-evb \
-drive file=u-boot-with-spl.bin,if=mtd,format=raw
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The HACE driver lacks support for all the hash types, causing boot to
fail with the default FIT configuration which uses CRC32.
Additionally the Qemu model or the u-boot driver is unable to correctly
compute the SHA256 hash used in a FIT.
Disable HACE by default while the above issues are worked out to enable
boot testing in Qemu.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Allows loading one u-boot from another. Useful for testing on hardware.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Useful for testing images with the default hash type.
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
