The bootaux uses ulong to read private data and write to M4 TCM,
this cause problem on ARM64 platform where the ulong is 8bytes.
Fix it by using u32 to replace ulong.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the support for loading image from secondary container set on
iMX8QM B0, iMX8QXP C0.
Using the SCFW API to get container set index, if it is the secondary
boot, get the offset from fuse and apply to offset of current container
set beginning for loading.
Also override the emmc boot partition to check secondary boot and switch
to the other boot part.
This patch is modified from NXP downstream:
imx8: Fix the fuse used by secondary container offset
imx: container: Skip container set check for ROM API
imx8: spl: Support booting from secondary container set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Checking container header tag and version is wrong, it causes to fail
to bypass invalid container
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix below coverity issues caused by get_idx function where "-1" is
compared with uint8_t "element"
343336 Unsigned compared with neg
343337 Operands don't affect result
Additional, this function returns "-1" will cause overflow to
event string array.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Extend the RX timeout value to 10s, because when authentication is failed
the ELE needs long time (>2s for 28M image) to return the result. Print
rx wait info per 1s.
Also correct TX and RX status registers in debug.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to SRM, the Sentinel MU has 8 TR and 4 RR registers. All
of them are used for ELE message. So update TR count to 8 and fix a
typo in receive msg
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity (CID 21143558).
When tee_shm_register returns failure, the shm_input pointer is
invalid, should not free it. Same issue also exists on registering
shm_output.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix build warning:
warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3
has type ‘u64’ {aka ‘long long unsigned int’} [-Wformat=]
printf("can't find memreg for image %d load address 0x%x, error %d\n",
warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but
argument 3 has type ‘sc_faddr_t’ {aka ‘long long unsigned int’} [-Wformat=]
debug("memreg %u 0x%lx -- 0x%lx\n", mr, start, end);
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Running a memtest in U-Boot and Linux shows that some Colibri iMX6
produce bitflips at temperatures above 60°C. This happens because the
RALAT and WALAT values on the Colibri iMX6 are too low. The problems
were introduced by commit 09dbac8174 ("mx6: ddr: Restore ralat/walat
in write level calibration") before the calibration process overwrote
the values and set them to the maximum value. With this commit, we make
sure that the RALAT and WALAT values are set to the maximum values
again. This has been proven to work for years.
Fixes: 09dbac8174 ("mx6: ddr: Restore ralat/walat in write level calibration")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add support for Winbond 256M-bit flash w25q256jwm.
Performed basic erase/write/readback operations on
ZynqMP zc1751+dc1 board.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If cs gpio is requested with ACTIVE_HIGH flag, it will
be pulled low(i.e. active). This is not what we expected.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
XTX changed full company name from "XTX Technology (Shenzhen) Limited
to "XTX Technology Limited" since 2020,So remove "(Shenzhen)".
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to Documentation/devicetree/bindings/spi/spi-gpio.yaml
from Linux, the recommended spio-gpio properties are:
sck-gpios, miso-gpios and mosi-gpios.
gpio-sck, gpio-mosi and gpio-miso are considered deprecated.
Update the bindings to suggest the recommeded properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to Documentation/devicetree/bindings/spi/spi-gpio.yaml
from Linux, the recommended spio-gpio properties are:
sck-gpios, miso-gpios and mosi-gpios.
gpio-sck, gpio-mosi and gpio-miso are considered deprecated.
Currently, U-Boot only supports the deprecated properties.
Allow the soft_spi driver to support both the new and old properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Current code expects that SPI_TX_BYTE is single bit mode
but it is wrong. It indicates byte program mode,
not single bit mode.
If SPI_TX_DUAL, SPI_TX_QUAD and SPI_TX_OCTAL bits are not set,
the default transfer bus width is single bit.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The newer BCMBCA SoCs such as BCM6756, BCM4912 and BCM6855 include an
updated SPI controller that add the capability to allow the driver to
control chip select explicitly. Driver can control and keep cs low
between the transfers natively. Hence the dummy cs workaround or prepend
mode found in the bcm63xx-hsspi driver are no longer needed and this new
driver is much cleaner.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-15-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Due to the controller limitation to keep the chip select low during the
bus idle time between the transfer, a dummy cs workaround was used when
this driver was first upstreamed to the u-boot based on linux kernel
driver. It basically picks the dummy cs as !actual_cs so typically dummy
cs is 1 when most of the case only cs 0 is used in the board design.
Then invert the polarity of both cs and tell the controller to start the
transfers using dummy cs. Assuming both cs are active low before the
inversion, effectively this keeps dummy cs high and actual cs low during
the transfer and workaround the issue.
This workaround requires that dummy cs 1 pin to is set to SPI chip
selection function in the pinmux when the transfer clock is above 25MHz.
The old chips likely have default pinmux set to chip select on the dummy
cs pin so it works but this is not case for the new Broadband BCA chips
and this workaround stop working. This is specifically an issue to
support SPI NAND and SPI NOR flash because these flash devices can
typically run at or above 100MHz.
This patch utilizes the prepend feature of the controller to combine the
multiple transfers in the same message to a single transfer when
possible. This way there is no need to keep clock low between transfers
and solve the issue without any pinmux requirement.
Multiple transfers within a SPI message may be combined into one
transfer if the following are all true:
* One or more half duplex write transfer in single bit mode
* Optional full duplex read/write at the end
* No delay and cs_change between transfers
Most of the SPI device meets this requirements such as SPI NOR, SPI NAND
flash, Broadcom SPI voice card and etc. So this change switches to the
prepend mode as the default mode. For any SPI message that does not meet
the above requirement, we switch to original dummy cs mode but limit the
clock rate to the safe 25MHz.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-12-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
New compatible string brcm,bcmbca-hsspi-v1.0 is introduced based on
dts document brcm,bcm63xx-hsspi.yaml. Add it to the driver to support
this new binding.
Port from linux patch:
Link: https://lore.kernel.org/r/20230207065826.285013-6-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
Fixes: 29cc4368ad ("dm: spi: add BCM63xx HSSPI driver")
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-11-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
ARCH_BCMBCA was introduced to cover individual Broadcom broadband SoC
for common features and IP blocks. Use this config instead of each chip
config as the Kconfig dependency for Broadcom HSSPI driver.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for an optional external chip-select gpio.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Remove the platform data header because its content is only used by the
driver.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rename the flush function into pl022_spi_flush to avoid conflicting
types with previous declaration of the function in stdio.h header.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Align the compatible property with the kernel device tree binding [1]
by removing the '-spi' suffix.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/spi/spi-pl022.yaml
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The NAND flash controller (NFC) on the AC5/AC5X SoC is the same as
the NFC used on other Marvell SoCs. It does have the additional
restriction of only supporting SDR timing modes up to 3.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The NF_CLK for the AC5 SoC runs at 400MHz. There's no strapping
or gating require so just add a mvebu_get_nand_clock() that
returns this value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The AC5/AC5X SoC has a NAND flash controller. Add this to the
SoC device tree.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Update the Thecus N2350 DTS to conform with latest device-tree binding
and styles.
- Correct typo in mdio node.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
