Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Currently accessing the SD card on USDHC2 fails with:
=> mmc dev 1
Card did not respond to voltage select! : -110
This is due to the fact that UHS modes are enabled in the defconfig
and the devicetree, but the referenced LDO5 regulator (reg_nvcc_sd)
is not available to switch the data lines from 3.3V to 1.8V mode.
By enabling the regulator driver the vqmmc-supply is now available
and the SD card works also in high speed modes:
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Please note that the board has a GPIO connected to the SD_VSEL signal
of the PMIC. As the driver uses the LDO5CTRL_H register to set the
voltage, we need to make sure that this GPIO (GPIO01_IO4) is set to
a high level.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Fabio Estevam <festevam@denx.de>
Select the CMD_UNZIP option so that the 'gzwrite' command
can be used to flash wic.gz image into the eMMC.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
Even if board can be successfuly built, CI goes in deadlock (see thread
on https://www.mail-archive.com/u-boot@lists.denx.de/msg419663.html).
This is caused by SYS_CONFIG set in header file and because defconfig
for the board is out of sync with Kconfig. As result, buildman goes on
to read from stdin until an OOM is reached.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Frieder Schrempf <frieder.schrempf@kontron.de>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
