Not all systems have all the boot devices enabled, e.g. not all systems
have MTD devices and thus do not enable UBI. Make all the boot devices
in the distro bootcmd conditional to avoid failures.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Let board code override setup_mac_address(), which is useful e.g. if the
board derives the MAC address from another source, like an I2C EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The main prompt for this (defined in /Kconfig) is visible at all times,
which means there's no reason to have an additional, machine-specific
prompt to set the same option.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SoC base addresses should better go into a common SoC file instead
of repeating the definition in each board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As we use the driver model for ESDHC there is no need
for defining CONFIG_SYS_FSL_USDHC_NUM and CONFIG_SYS_FSL_ESDHC_ADDR,
so simply remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Clearfog: Fix SD booting (Baruch)
- Misc updates to MMC handling in SPL to support booting from
main data partition (vs hardware boot partition) on MVEBU (Baruch)
This patch add CONFIG_TARGET_MT7623 into mt7623n_bpir2_defconfig
to fix the mt7623 compile error after building others mediatek target
platform
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This patch move u-boot properties to -u-boot.dtsi file.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
This patch add mmc and sd support for Mediatek MT7622 SoCs
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This patch add power domain support for Mediatek MT7622 SoCs
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
This patch fix clock-rate overflow problem in mediatek
clock driver common part.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Due to the pinctrl hardware of MT7622 is difference from others
SoC which using the common part of mediatek pinctrl.
So we need to modify the common part of mediatek pinctrl.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Add support for MediaTek MT7622 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
If make the ref clock optional, no need refer to fixed-clock when
the ref clock is always on or comes from oscillator directly.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
No need check -ENOSYS anymore after add dummy_enable() for
fixed-clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This is used to avoid clk_enable() return -ENOSYS.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Sometimes we may need get (optional) clock without a device,
that means use ofnode.
e.g. when the phy node has subnode, and there is no device created
for subnode, in this case, we need these new APIs to get subnode's
clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Add valid check for clk->dev, it's useful when get optional
clock even when the clk point is valid, but its dev will be
NULL.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
If skip all return error number, it may skip some real error cases,
so only skip the error when the clock is not provided in DTS
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
The SSUSB IP's clocks come from ssusbsys module on mt7629,
so add its driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Add support for MediaTek MT8512 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Sam doesn't work for Linaro anymore, so Linaro mail is not valid. Change
it to his home mail instead.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
When no partition table is found, users should be warned so.
Warning that no device is available in this case could be misleading,
especially as it is the same error when no device is selected.
Signed-off-by: Alexandre Besnard <alexandre.besnard@softathome.com>
SPL now automatically selects the correct U-Boot image offset for both
eMMC and SD card. No need to tweak
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR anymore.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Armada 38x ROM skips the first SD card offset when loading SPL. This
affects the location of the main U-Boot image. SPL MMC code now supports
U-Boot image offset based on run-time detection of the boot partition.
Use this feature to make the same generated image support both SD card
and eMMC boot partition.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
On Armada 38x platforms the ROM code loads SPL from offset 0 of eMMC
hardware boot partitions. When there are no boot partitions (i.e. SD
card) the ROM skips the first sector that usually contains the (logical)
partition table. Since the generated .kwb image contains the main U-Boot
image in a fixed location (0x140 sectors by default), we end up with the
main U-Boot image in offset of 1 sector. The current workaround is to
manually set CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x141 to
compensate for that.
This patch uses the run-time detected boot partition to determine the
right offset of the main U-Boot partition. The generated .kwb image is
now compatible with both eMMC boot partition, and SD card main data
partition.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPL needs DM GPIO to read the SD card-detect signal. This complements
the fix in commit 70bae02f71 ("arm: mvebu: clearfog: fix boot from SD
card").
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.
Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
The eSDHC reference clocks should be provided by speed.c in arch/.
And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to
select which clock to use. Because we can make the driver to select
the periperhal clock which is better (provides higher frequency)
automatically if its value is provided by speed.c.
This patch is to drop this option and make driver to select clock
automatically. Also fix peripheral clock calculation issue in
fsl_lsch2_speed.c/fsl_lsch3_speed.c.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The QorIQ eSDHC controller supports two reference clocks. They are
platform clock and periperhal clock. The global variable sdhc_clk
has already been used for platform clock.
This patch is to add another global variable sdhc_per_clk for
periperhal clock, which provides higher frequency and is required
to be used for SD UHS and eMMC HS200/HS400 speed modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The below patch added eSDHC periperhal clock code initially.
2d9ca2c mmc: fsl_esdhc: Add peripheral clock support
The purpose was to fix up device tree properties "peripheral-frequency"
so that linux could get the periperhal clock by it.
However the implementation on both u-boot and linux was only
for a Freescale SDK release. The linux part implementation had never
been upstreamed. These code should not have been exist on u-boot
mainline.
Let's remove the powerpc part changes but keep the changes in
fsl_esdhc driver. The changes in fsl_esdhc driver could be utilized
to support SD UHS and eMMC HS200/HS400 speed modes for current
Layerscape ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fdt fixup for properties "peripheral-frequency" and "adapter-type"
was once for a Freescale SDK release. The properties haven't been existed
in linux mainline. Drop these useless code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The device tree compiler expects that a node with a unit-address has a reg
property.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
