Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add entry for 3732 MT/s mode of operation of the LPDDR4, in
which case the DDR PLL has to be configured in 933 MHz mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add DT compatible string for PCA9450C PMIC. This is a variant of the
PCA9450 PMIC with 6 A dual-phase buck regulator and 3 A buck regulator,
and is software-wise compatible with the PCA9450B. This variant of the
PCA9450 is designed for use as companion PMIC for i.MX8MP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The correct compatible string for i.MX8MP variant of DWC EQoS MAC
is "nxp,imx8mp-dwmac-eqos", use it. Drop the two current users of
the current wrong compatible string to avoid breaking them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
added device tree support for job ring driver.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
-----BEGIN PGP SIGNATURE-----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=SxkC
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
With dm-tag feature, any U-Boot subsystem is allowed to associate
arbitrary number of data with a particular udevice. This can been
see as expanding "struct udevice" without modifying the definition.
As a first user, UEFI subsystem makes use of tags to associate
an efi_disk object with a block device.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time an ide bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time a sata bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time a nvme bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time a mmc bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Every time a scsi bus/port is scanned and a new block device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Take as reference Linux kernel code:
drivers/gpio/gpio-pca953x.c
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the CONFIG macros to conditionally build the GPIO hogging support in
either the SPL or U-Boot, or both, depending on the configuration. Also
call the GPIO hog probe function in the common SPL board initialization
as an equivalent to adding it to the U-Boot init sequence functions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for the upstream gpio-line-names property already described
in the common GPIO binding document[1]. The ability to search for a line
name allows boards to lift the implementation of common GPIO behaviours
away from specific line indexes on a GPIO controller.
[1] 3c35bfee83/dtschema/schemas/gpio/gpio.yaml (L17)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_SCIF0
CONFIG_CONS_SCIF1
CONFIG_CONS_SCIF2
CONFIG_CONS_SCIF4
CONFIG_CONS_SCIFA0
Signed-off-by: Tom Rini <trini@konsulko.com>
When SPI flash is used in SPL there is no console, so ctrlc() cannot be
called. Add a condition to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The tps65217 PMIC driver is used with am335x SoC based designs.
It is used in the SPL (MLO) as well, so the DM conversion only is
for u-boot proper.
This driver only allows simple reading/writing/dumping of the content
of its registers and requires the DM_I2C for proper operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
In current slg7xl45106 gpio driver xlate() function we are not updating
gpio flags from DT. Read the given flag from DT and update the gpio desc
flags variable with required gpio direction state.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/a8d7b4799337bd99f61ace509889f02b192a9414.1648631275.git.michal.simek@xilinx.com
As we are not reading the PHY address in case of CONFIG_ETH_PHY in plat
function, phy address always prints as -1. So move the ethernet info
print statement to probe function, to display proper phy address.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f6efc6719d767b1bebe65987c22c6d52329f4225.1648631275.git.michal.simek@xilinx.com
If DM_ETH_PHY config is enabled PHY gpio reset is taken care by the
eth-phy-uclass driver, so use the PHY gpio reset functionality from
ethernet_id file when this config is disabled to reset the PHY.
Use debug() print instead of dev_err() to avoid warning incase if phy-id
compatible string is not present.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/4d0fd3f9f886c1d943776025e5efb5438b0eb389.1648631275.git.michal.simek@xilinx.com
While creating a phy device using phy_device_create(), we need to
provide a valid phyaddr instead of 0 causing phy address being
registered as 0 with mdio bus and shows mdio phy list as below
ZynqMP> mdio list
eth0:
0 - TI DP83867 <--> ethernet@ff0b0000
eth1:
0 - TI DP83867 <--> ethernet@ff0c0000
Also PHY soft reset is being requested on 0 instead of valid
address causing "PHY reset timed out" error.
So add phyaddr argument to phy_connect_phy_id() and to its prototype
to create phy device with valid phyaddress.
Fixes: a744a284e3 ("net: phy: Add support for ethernet-phy-id with gpio reset")
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Link: https://lore.kernel.org/r/fe35fddb9faa5af577ffdfabaec6879c935a30f8.1648562755.git.michal.simek@xilinx.com
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Makes it possible to use 16-bit DDR memory.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Introduce ECC Functionality for full memory space as implemented in the
DDRSS. The following is done to accomplish this:
* Introduce a memory region "ss" to allow dt to provide DDRSS region,
which is not the same as "ctl" which is the controller region.
* Introduce a "ti,ecc-enable" flag which allows a memorycontroller
instance to enable ecc.
* Introduce functionality to properly program the DDRSS registers to
enable ECC for the full DDR memory space if enabled with above flag.
* Expose a k3_ddrss_ddr_fdt_fixup call to allow fixup of fdt blob to
account from DDR memory that must be reserved for ECC operation.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The current address being read from dt actually represents the ddrss_ctl
memory region, while ddrss_ss region is something else. Introduce
ddrss_ctl_regs and use it to free up ddrss_ss_regs for its proper
purpose later so that we can avoid confusion.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
