Commit graph

34347 commits

Author SHA1 Message Date
Ye.Li
1a1f795078 imx: gpt: Add High frequency clock source support for GPT
Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set,
the GPT will select a high frequency clock as clock source.
Otherwise, the GPT will stay to use 32Khz OSC as clock source.

In the implementation, since only the GPT on i.MX6 series provide the
clock source option for 24Mhz OSC. For others (only i.MX5 and i.MX6
compile the driver), if the configuration is set, the perclk will be
selected as clock source.
MX6Q/D Rev 1.0 and MX6SL are special in the implementation, because they
don't have the 24Mhz OSC clock source option, so also select the perclk
for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so
eventually the clock comes from OSC 24Mhz.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-03 11:21:41 +01:00
Ye.Li
de97980478 imximage: Fix the bootdata.size calculation
In system boot chapter of i.MX6 reference manual, the "Image Vector Table"
figure shows the bootdata.start points to the beginning of the destination
memory. It means the bootdata.size should contain the IVT offset part,
but the calculation in imximage tool does not have.

We found this issue when booting from QuadSPI NOR on i.MX6SX. The u-boot
runs into abnormal (crash or stop) after booting. After checked the destination
memory where the image is loaded to, there are hundreds of bytes at
the image end are not loaded into memory. Since there is a 4096 bytes
round in the calculation, for the booting devices using smaller IVT offset,
such as SD and SPI booting, they are not easy to reproduce.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-03 10:33:01 +01:00
Daniel Schwierzeck
265072ba75 MIPS: add .padding section to linker script
Commit 79fd7e649e

    MIPS: always keep all sections in u-boot ELF binary.

    Always keep all sections in u-boot ELF binary. Move all unneeded
    sections after _end to avoid allocating space in the final binary.
    Also remove .deadcode section which is now obsolete.

removed section .deadcode because the original symptoms were not
visible anymore. Unfortuneatly the binutils bug still exists.

The size of .rel.dyn section is often bigger than needed for all
entries. But objcopy only allocates space as much as required for all
reloc entries. Thus there is a gap between the last entry and
__rel_dyn_end in u-boot.bin. If u-boot is booted from RAM (e.g. in
SPL scenarios) that area could contain garbage data which could lead
to CPU exceptions during relocation.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:05 +01:00
Daniel Schwierzeck
837cad1e47 MIPS: refactor setting of compiler options
Refactor and unify all compiler settings in arch/mips/config.mk.
Also add tune flags for each supported CPU type.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:05 +01:00
Daniel Schwierzeck
4207917867 MIPS: kconfig: add options for vct board variant select
The vct board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
2014-11-01 18:18:05 +01:00
Daniel Schwierzeck
edf7dbba69 MIPS: kconfig: add options for dbau1x00 board variant select
The dbau1x00 board can be built with various variants which are
configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus
add new Kconfig options for those board variants.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:05 +01:00
Daniel Schwierzeck
aa45f75eaf MIPS: kconfig: merge targets qemu_mips and qemu_mips64
Now the user can separately select the CPU type. Thus the
targets qemu_mips and qemu_mips64 can be merged to a single
target.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:04 +01:00
Daniel Schwierzeck
b9863b6de2 MIPS: kconfig: globally define CONFIG_SYS_CPU for MIPS
Now the user can select the CPU type for each target. Thus
CONFIG_SYS_CPU could be set globally.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:04 +01:00
Daniel Schwierzeck
02611cbb7c MIPS: kconfig: add options for CPU type select
Add new Kconfig option to let the user select the targets
CPU type. Each target have to select SUPPORTS_CPU_MIPS[32,64]_R[1,2]
to indicate which CPU types are supported.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:03 +01:00
Daniel Schwierzeck
0e1dc3456f MIPS: kconfig: add options for endianess select
Add new Kconfig option to let the user select the targets
endianess. Each target have to select SUPPORTS_BIG_ENDIAN
and/or SUPPORTS_LITTLE_ENDIAN to indicate which endianess
is supported.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:17:22 +01:00
Marek Vasut
8a78ca9ea5 arm: socfpga: Add example config entry for EPCS/EPCQ SPI
Add example config file entry for the Altera SPI controller. This SPI
controller can also, under special conditions, be used to operate the
EPCS/EPCQ SPI NOR.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-31 10:18:05 +01:00
Masahiro Yamada
548b310c68 Remove the CREDITS file
This file is not maintained these days.

We use MAINTAINERS for the maintainership of the supported boards.
For dead boards, we have some clues in doc/README.scrapyard and
also imperishable history in git-log.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-By: Wolfgang Denk <wd@denx.de>
2014-10-31 00:50:51 +01:00
Fabio Estevam
953d27a105 novena: Add MAINTAINERS file
Commit f91c09acf5 ("ARM: mx6: Add support for Kosagi Novena") missed to
add a MAINTAINERS file, so add Marek as the maintainer.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-10-31 00:46:35 +01:00
Masahiro Yamada
b445c33a68 ppc/arm: remove remainders of dead boards in Kconfig
Commit d58a9451e7 (ppc/arm: zap EMK boards) removed
TOP* boards support but missed to remove entries in Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
2014-10-31 00:42:19 +01:00
Masahiro Yamada
9ea7f3a6d8 Remove unused files
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
 The top9000 was the last board to use this header file.
 It was removed by commit d58a9451e7 (ppc/arm: zap EMK boards).

[2] board/matrix_vision/common/*
 Some Matrix Vision boards were dropped by commit e7a565638a
 (powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
 and commit af55e35d33
 (powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
 Since then these files have been unused.

[3] include/usb/omap1510_udc.h
  The omap5912osk was the last board to use this header file.
  It was removed by commit 62d636aa2a
  (omap: remove omap5912osk board support).

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
2014-10-31 00:38:15 +01:00
Paul Kocialkowski
2ed8c878eb twl4030: VMMC2 3.2V enable on MMC init
This enables the VMMC2 LDO, which powers the MMC2 device.
When the device starts from MMC2, this has already been enabled by the BootROM,
but when starting from peripheral boot (USB, UART), it is not the case.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-31 00:29:39 +01:00
Stefan Roese
934a529f94 tools/kwbimage: Fix compilation warning
This patch fixes a compilation warning of kwbimage.c:

tools/kwbimage.c: In function ‘kwbimage_set_header’:
tools/kwbimage.c:784:8: warning: ‘headersz’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  memcpy(ptr, image, headersz);
        ^
Instead of using multiple if statements, use a switch statement with
a default entry. And return with error if an unsupported version
is configured in the cfg file.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-By: Wolfgang Denk <wd@denx.de>
2014-10-31 00:29:29 +01:00
Andreas Bießmann
e5f1a586a7 tools/kwbimage.c: fix build on darwin
kwbimage uses get_current_dir_name(3) which is a gnu extension and not
available on darwin host. Fix this by converting to portable getcwd(3)
function.

This patch fixes the following error:
---8<---
  HOSTCC  tools/kwbimage.o
tools/kwbimage.c:399:16: warning: implicit declaration of function 'get_current_dir_name' is invalid in C99 [-Wimplicit-function-declaration]
                        char *cwd = get_current_dir_name();
                                    ^
tools/kwbimage.c:399:10: warning: incompatible integer to pointer conversion initializing 'char *' with an expression of type 'int' [-Wint-conversion]
                        char *cwd = get_current_dir_name();
                              ^     ~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
...
Undefined symbols for architecture x86_64:
  "_get_current_dir_name", referenced from:
      _image_headersz_v1 in kwbimage.o
ld: symbol(s) not found for architecture x86_64
--->8---

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
[agust: fixed getcwd() return warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2014-10-31 00:26:12 +01:00
Soeren Moch
d37e96ecb9 video: speedup writing strings to fb console
With enabled framebuffer console the printenv command can take several
seconds to complete. This patch temporarily disables cache flush when
writing strings to fb console. Then there is no noticable delay anymore.

Tested with imx6 hdmi framebuffer.

Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-10-30 21:45:25 +01:00
Marek Vasut
d12159b63b arm: mxs: Define bootscript env variable on m28evk
The patch below failed to define the variable, so define it
to make it consistent with M53EVK.

commit a428ac914b
Author: Lothar Rubusch <lothar@denx.de>
Date:   Thu Jun 26 11:01:29 2014 +0200

    ARM: m28evk: Update default environment

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-10-30 15:18:21 +01:00
Soeren Moch
4bfa2db8e1 arm: arch-mx6: typo fixes in crm_regs.h
fix typos in video pll related register names and bit defines

Signed-off-by: Soeren Moch <smoch@web.de>
2014-10-30 11:58:18 +01:00
Przemyslaw Marczak
4aa97312f7 odroid: adjust gpio calls to dm gpio api
Setting gpio value before dm gpio init has no effect,
so now, odroid gpio settings are moved after the gpio uclass init.

Using non-requested gpio pin cases printing error messages.
To avoid this, gpio_request() is added for those gpios.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-30 19:56:16 +09:00
Przemyslaw Marczak
9e306f15c6 exynos4/4x12: gpio: use gpio extra base addresses
This patch adds extra gpio part addresses to exynos4
and exynos4x12_gpio_data arrays, which are required
since the gpio enum lists are linear

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-30 19:56:16 +09:00
Przemyslaw Marczak
92f4dbaf1a exynos4/4x12: cpu: add extra gpio base addresses
After remove the offsets in Exynos4/4x12 gpio enums,
an additional gpio base addresses are required.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-30 19:56:16 +09:00
Marek Vasut
f9cfe17b3d mtd: nand: mxs: Add ECC geometry for 2048b/112b NAND
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB
size. This is for example Macronix MX30LF2G28AB chip.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-10-30 11:02:23 +01:00
Anatolij Gustschin
9c56936eb5 arm: imx6: fix typos in CCM_ANALOG_PLL_VIDEO_DENOM register name
Fix name for Video PLL denominator register.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2014-10-30 10:51:24 +01:00
Nikolay Dimitrov
b99ed2766a novena: Fix ethernet PHY reset sequence
This patch fixes conflict between PHY pins becoming outputs after reset and
imx6 still driving the pins. It also fixes the reset timing as recommended by
the PHY datasheet.

Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-30 10:48:43 +01:00
Christian Gmeiner
56740fa96f ot1200: rework card detect for eMMC
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-30 10:46:28 +01:00
Christian Gmeiner
5a9ca420ce ot1200: add support for usdhc4
On the 'mr' variant switching to 'mmc dev 1' will result
in "MMC: no card present".

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-30 10:46:28 +01:00
Christian Gmeiner
1199ddce9c ot1200: add feature pads
The older 'mr' variant and the generic variant of the
OT1200 differ in some places. As the name suggests the
generic variant supports more boot devices.

In order to be compatible with the 'mr' variant we define
some 'feature' GPIOs. On the 'mr' variant this pads are
not connected so we define their state with the help
of the internal pullups.

On the generic variant this GPIOs are connected and
represent the state of the hardware.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-30 10:46:28 +01:00
Markus Niebel
29fd5c289c tqma6: fix typo in header guard define
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-10-30 10:43:35 +01:00
Markus Niebel
1719d49c34 tqma6: fix sf detection
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-10-30 10:43:12 +01:00
Stefan Roese
ebcaf966ed arm: socfpga: Add I2C support to SoCFPGA
This patch adds I2C support for the SoCFPGA. Using the designware I2C
controller driver. It supports all 4 I2C busses on the SoCFPGA.

The designware I2C driver has now been converted to the
CONFIG_SYS_I2C framework. So lets enable it on SoCFPGA.

Tested on SoCrates.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2014-10-30 10:17:47 +01:00
Fabio Estevam
ca9d817ab5 mx6sabresd: Add Seiko WVGA panel support
Add support for the 4.3'' Seiko WVGA parallel display.

In order to direct the splash screen to the Seiko display:

=> setenv panel SEIKO-WVGA
=> save
=> reset

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-10-30 10:11:39 +01:00
Marek Vasut
f91c09acf5 ARM: mx6: Add support for Kosagi Novena
Add support for the Kosagi Novena board. Currently supported are:
- I2C busses
- FEC Ethernet
- MMC0, MMC1, Booting from MMC
- SATA
- USB ports
- USB Ethernet

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Nikolay Dimitrov <picmaster@mail.bg>
Reviewed-by: Nikolay Dimitrov <picmaster@mail.bg>
2014-10-30 10:09:06 +01:00
Jeroen Hofstee
9df4757718 board: wandboard: add usb storage
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-30 10:06:34 +01:00
Tom Rini
2c54cb5516 Merge git://git.denx.de/u-boot-x86 2014-10-29 15:57:59 -04:00
Tom Rini
b8be4e365c Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2014-10-29 15:57:33 -04:00
Simon Glass
026090e4c5 x86: config: Increase CONFIG_SYS_BOOTM_LEN to 16MB
The code density of x86_64 is not wonderful. Increase the maximum boot
size and adjust the load address to cope.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-29 13:11:54 -06:00
Wolfgang Denk
69445d6c56 powerpc: TQM5200: convert to generic board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-10-29 16:18:09 +01:00
Wolfgang Denk
23c5d253d5 powerpc: tqm8xx*: convert to generic board
This converts all TQM8xx boards (MPC8xx based) to generic board.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-10-29 16:18:08 +01:00
Masahiro Yamada
d9bc8fd1cb serial: UniPhier: add static to locally used functions
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29 22:53:42 +09:00
Masahiro Yamada
bb72148b2b serial: UniPhier: add .pending handler
Without .pending handler, tstc() function always returns 1.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29 22:53:42 +09:00
Masahiro Yamada
59ca5537be ARM: UniPhier: make pinmon command optional
Add CONFIG_CMD_PINMON to UniPhier-specific Kconfig and make the
"pinmon" command user-configurable.  This command can be disabled
via the configuration if users do not need it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29 22:53:42 +09:00
Georges Savoundararadj
571bdf16a7 arm: interrupt_init: set sp in IRQ/FIQ modes
Before this commit, the stack addresses for IRQ and FIQ modes,
IRQ_STACK_START and FIQ_STACK_START, were computed in interrupt_init but
they were not used.

This commit sets the stack pointers for IRQ and FIQ modes.

Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-10-29 09:03:28 -04:00
Georges Savoundararadj
3ff46cc42b arm: relocate the exception vectors
This commit relocates the exception vectors.
As ARM1176 and ARMv7 have the security extensions, it uses VBAR.  For
the other ARM processors, it copies the relocated exception vectors to
the correct address: 0x00000000 or 0xFFFF0000.

Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Warren <twarren@nvidia.com>
2014-10-29 09:02:50 -04:00
Georges Savoundararadj
c57a642384 arm: make .vectors section allocatable
A regression was introduced in commit 41623c91. The consequence of that
is the non-relocation of the section .vectors symbols :
_undefined_instruction, _software_interrupt, _prefetch_abort,
_data_abort, _not_used, _irq and _fiq.

Before commit 41623c91, the exception vectors were in a .text section.
The .text section has the attributes allocatable and executable [1].

In commit 41623c91, a specific section is created, called .vectors, with
the attribute executable only.

What have changed between commit 41623c91^ and 41623c91 is the attribute
of the section which contains the exception vectors.
An allocatable section is "a section [that] occupies memory during
process execution" [1] which is the case of the section .vectors.
Adding the lacking attribute (SHF_ALLOC or "a") for the definition of
the section .vectors fixed the issue.

To summarize, the fix has to mark .vectors as allocatable because the
exception vectors reside in "memory during execution" and they need to
be relocated.

[1] http://man7.org/linux/man-pages/man5/elf.5.html

Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-10-29 09:02:17 -04:00
Georges Savoundararadj
2e07c249a6 kconfig: arm: introduce symbol for ARM CPUs
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.

For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.

Also, it removes redundant "string" type in some Kconfig files.

Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29 09:02:09 -04:00
Stefan Roese
678398b19e i2c: designware: Convert driver to multibus/multiadapter framework
In preparation for the SoCFPGA support of the designware I2C driver,
convert this driver to the common CONFIG_SYS_I2C framework.

This patch converts all users of this driver, this is:

- ST spearxxx boards
- AXS101 (ARC700 platform)

I couldn't test this patch on those boards. Only compile tested for all
spear boards. And tested on SoCFPGA.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-29 08:56:23 +01:00
Marek Vasut
318a9cea49 i2c: mxs: Add support for I2C 1 on i.MX28
Add support for I2C bus 1 on the i.MX28.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2014-10-29 08:56:07 +01:00