Commit graph

69 commits

Author SHA1 Message Date
Masahiro Yamada
24572db909 pinctrl: uniphier: add UniPhier sLD3 pinctrl driver
Add pin-mux support for UniPhier sLD3 SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:17 +09:00
Masahiro Yamada
bbb119800f pinctrl: uniphier: support 4bit-width pin-mux register capability
On LD4 SoC or later, the pin-mux registers are 8bit wide, while 4bit
wide on sLD3 SoC.  Support it for the sLD3 pinctrl driver.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:11 +09:00
Masahiro Yamada
cdc7e3cb32 pinctrl: uniphier: move register base macros from header to .c file
These macros are only referenced in pinctrl-uniphier-core.c, so
they need not reside in a header file.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14 22:54:19 +09:00
Masahiro Yamada
865a39a23f pinctrl: uniphier: add System Bus pin-mux settings
This is needed to get access to UniPhier System Bus (external bus).

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14 22:54:19 +09:00
Beniamino Galvani
677b53580d pinctrl: add driver for meson-gxbb pin controller
Add a pin controller driver for Meson GXBB adapted from Linux kernel.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06 13:18:19 -04:00
Beniamino Galvani
2c936374c8 pinctrl: generic: scan for "pins" and "groups" properties in sub-nodes
In cases where the pins and groups definitions are in a sub-node, as:

	uart_a {
		mux {
			groups = "uart_tx_a", "uart_rx_a";
			function = "uart_a";
		};
	};

pinctrl_generic_set_state_subnode() returns an error for the top-level
node and pinctrl_generic_set_state() fails. Instead, return success so
that the child nodes are tried.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-06 13:18:19 -04:00
Masahiro Yamada
f835706c29 pinctrl: fix typos in comment blocks of pinconfig_post_bind()
'-' is never used in function names.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-20 14:03:28 -04:00
Wenyou Yang
ac72e174f9 pinctrl: at91-pio4: Add pinctrl driver
AT91 PIO4 controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.

The pin configuration is performed on specific registers which
are shared along with the gpio controller. So regard the pinctrl
device as a child of atmel_pio4 device.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-08-15 22:58:03 +02:00
John Keeping
2b51784aef rockchip: rk3288: Fix pinctrl for GPIO bank 0
Bank 0 is the "PMU GPIO" bank which is controlled by the PMU registers
rather than the GRF registers.  In the GRF the top half of the register
is used as a mask so that some bits can be updated without affecting the
others, but in the PMU this feature is not provided and the top half of
the register is reserved.

Take the same approach as the Linux driver to update the value via
read-modify-write but setting the mask for only the bits that have
changed.  The PMU registers ignore the top 16 bits so this works for
both GRF and PMU iomux registers.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2016-07-31 07:24:20 -06:00
Simon Glass
911954859d dm: Use dm_scan_fdt_dev() directly where possible
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
2e3f1ff63f dm: Convert users from dm_scan_fdt_node() to dm_scan_fdt_dev()
This new function is more convenient for callers, and handles pre-relocation
situations automatically.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:07 -06:00
Heiko Stübner
041cdb5f3d cosmetic: rockchip: sort socs according to numbers
Having some sort of ordering proofed helpful in a lot of other places
already. So for a larger number of rockchip socs it might be helpful
as well instead of an ever increasing unsorted list.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:20 -06:00
Heiko Stübner
23c3042b10 cosmetic: rockchip: rk3036: pinctrl: fix config symbol naming
Rockchip socs are always named rkxxxx in all places, as also shown
by the naming of the rk3036 pinctrl file itself.
Therefore also name the config symbol according to this scheme.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:20 -06:00
Heiko Stübner
9f862ec717 cosmetic: rockchip: rk3288: pinctrl: fix config symbol naming
The rk3288 pinctrl is very specific to this soc, so should
not hog the generic rockchip naming.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:20 -06:00
Masahiro Yamada
4e3d84066e ARM: uniphier: use (devm_)ioremap() instead of map_sysmem()
This does not have much impact on behavior, but makes code look more
more like Linux.  The use of devm_ioremap() often helps to delete
.remove callbacks entirely.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24 00:13:10 +09:00
Simon Glass
d95b14ffab rockchip: pinctrl: Update the rk3288 driver to support of-platdata
Add support for of-platdata with rk3288. This requires disabling access to
the device tree and renaming the driver to match the string that of-platdata
will search for.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14 20:40:24 -06:00
Masahiro Yamada
fc9da85c60 pinctrl: uniphier: add Ethernet pin-mux settings
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02 05:44:30 +09:00
Masahiro Yamada
64c1cc4cc5 pinctrl: uniphier: avoid building unneeded pin-mux tables for SPL
SPL does not use all of the devices, so we can save some memory
footprint.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02 05:44:30 +09:00
Masahiro Yamada
5e25b9d5d9 pinctrl: uniphier: support pin configuration for dedicated pins
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.

Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function.  The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.

[ Linux commit: 363c90e743b50a432a91a211dd8b078d9df446e9 ]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02 05:44:29 +09:00
Masahiro Yamada
3379987e26 pinctrl: uniphier: split pinctrl driver for PH1-LD11 and PH1-LD20
PH1-LD11 and PH1-LD20 have much pin controlling in common, so I
added a single driver shared between them in the initial commit.

However, the Ethernet pin-mux settings I am going to add are
different with each other, and they may diverge more as the
progress of development.  Split it into two dedicated drivers.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02 05:44:29 +09:00
Masahiro Yamada
186c133444 pinctrl: uniphier: allow to have pinctrl node under syscon node
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node.  This commit allows to migrate to
the new DT structure.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02 05:44:29 +09:00
Masahiro Yamada
aac641bcf4 pinctrl: uniphier: remove unneeded pin group nand_cs1
This SoC does not support NAND CS1.  This place-holder is no longer
necessary.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30 23:49:26 +09:00
Masahiro Yamada
69da34c073 pinctrl: uniphier: fix NAND pin-mux setting for PH1-LD11/LD20
My mistake in the initial support patch.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30 23:49:26 +09:00
Masahiro Yamada
4d1065c8d8 pinctrl: uniphier: remove wrong pin-mux functions for ProXstream2
These are pin group names, not function names.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30 23:49:26 +09:00
Tom Rini
d77fa2ff76 Merge http://git.denx.de/u-boot-samsung
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/peach-pi_defconfig
	configs/peach-pit_defconfig
2016-06-06 13:39:43 -04:00
Sjoerd Simons
70f7a2cdac rockchip: rk3288: pinctrl: support more pins
The rgmii_pins node in rk3288.dtsi configures 15 pins. Increase the size
of the cell array to accomedate that, otherwise only the first 10 get
configured.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-27 09:00:48 -06:00
Thomas Abraham
16ca80adc5 pinctrl: Add pinctrl driver support for Exynos7420 SoC
Add pinctrl driver support for Samsung's Exynos7420 SoC. The changes
have been split into Exynos7420 specific and common Exynos specific
portions so that this implementation is reusable on other Exynos
SoCs as well.

The Exynos pinctrl driver supports only device tree based pin
configuration. The bindings used are similar to the ones used in the
linux kernel.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 10:00:18 +09:00
Thomas Abraham
ac98527313 pinctrl: add the DM_UC_FLAG_SEQ_ALIAS flag for numbering the devices
It is possible to have multiple pin controllers in the system. Use the
DM_UC_FLAG_SEQ_ALIAS flag so that the pinctrl instances are assigned
a sequence number.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 10:00:18 +09:00
Wills Wang
c102453aeb drivers: pinctrl: Add simple pinctrl driver for Qualcomm/Atheros qca953x.
This is a simple pinctrl driver, it just support uart and spi pin-mux now.

Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[fixed typo in commit subject line]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-21 01:25:50 +02:00
Wills Wang
a79d0643f4 drivers: pinctrl: Add simple pinctrl driver for Qualcomm/Atheros ar933x.
This is a simple pinctrl driver, it just support uart and spi pin-mux now.

Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[fixed typo in commit subject line]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-21 01:25:50 +02:00
Masahiro Yamada
740314326d pinctrl: uniphier: fix NAND and SD pin-mux settings for PH1-LD11/LD20
I found many mistakes in the initial version.

Fixes: 8a3328c209 ("pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:53:54 +09:00
Masahiro Yamada
ac13ce49a4 pinctrl: uniphier: rename function/array names
Make function/array names match the file names for consistency.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:53:54 +09:00
Masahiro Yamada
6105aa2f2a pinctrl: uniphier: support UniPhier PH1-LD11 pinctrl driver
The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20
(as far as used in boot-loader), so this commit makes the driver
shared between the two SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:57:19 +09:00
Masahiro Yamada
8a3328c209 pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver
Add pin configuration and pinmux support for UniPhier PH1-LD20 SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:57:15 +09:00
Masahiro Yamada
3b05b5f0e4 pinctrl: uniphier: support per-pin input enable for new SoCs
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin.  (While, existing ones only support it
per pin-group.)  This commit prepares the core part for that.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:56:07 +09:00
Masahiro Yamada
8cc92b996d pinctrl: uniphier: introduce capability flag
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs.  This sometimes happens
because pinctrl drivers include really SoC-specific stuff.

This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding new ones.  Having flags would be better than
adding new members every time a new SoC-specific capability comes up.

At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from our customer.  For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:54:00 +09:00
Masahiro Yamada
510454db04 pinctrl: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:25 +09:00
Masahiro Yamada
ea65c98050 ARM: uniphier: drop PH1- prefix from CONFIG options and file names
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too
long.  It would not hurt to drop "PH1_" because "UNIPHIER_" already
well specifies the SoC family.  Also, rename files for consistency.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:42:13 +09:00
Masahiro Yamada
1d22c4b1bd pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.

The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long, so rename it
into CONFIG_PINCTRL_UNIPHIER.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-09 01:11:04 +09:00
Masahiro Yamada
fdd15b6a86 pinctrl: uniphier: set input-enable before pin-muxing
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.

Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
   (the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up.  The input signals to hardware block
   are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled.  The signals from the board reach the
    hardware block.

Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.

To avoid such problems, pins should be input-enabled before muxing.

[ ported from Linux commit bac7f4c1bf5e7c6ccd5bb71edc015b26c77f7460 ]

Fixes: 5dc626f836 ("pinctrl: uniphier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-09 01:10:52 +09:00
Peng Fan
c4068dfb31 pinctrl: imx: Support i.MX7D
Introudce i.MX7 pinctrl driver support.
For now only i.MX7D supported.
There are two iomux controllers in i.MX7D, iomuxc and iomuxc_lpsr.
To iomuxc_lpsr, ZERO_OFFSET_VALID is set, means offset of mux_reg
and conf_reg can begin at 0.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-21 11:25:29 +01:00
Peng Fan
745df68d36 pinctrl: imx: Introduce pinctrl driver for i.MX6
Introduce pinctrl for i.MX6
1. pinctrl-imx.c is for common usage. It's used by i.MX6/7.
2. Add PINCTRL_IMX PINCTRL_IMX6 Kconfig entry.
3. To the pinctrl_ops implementation, only set_state is implemented.
   To i.MX6/7, the pinctrl dts entry is as following:
&iomuxc {
        pinctrl-names = "default";

        pinctrl_csi1: csi1grp {
                fsl,pins = <
                MX6UL_PAD_CSI_MCLK__CSI_MCLK            0x1b088
                MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK        0x1b088
                MX6UL_PAD_CSI_VSYNC__CSI_VSYNC          0x1b088
                >;
        };

        [.....]
};
  there is no property named function or groups. So pinctrl_generic_set_state
  can not be used here.
5. This driver is a simple implementation for i.mx iomux controller,
   only parse the fsl,pins property and write value to registers.
6. With DEBUG enabled, we can see log when "i2c bus 0":
   "
   set_state_simple op missing
   imx_pinctrl_set_state: i2c1grp
   mux_reg 0x14c, conf_reg 0x3bc, input_reg 0x5d8, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
   write mux: offset 0x14c val 0x10
   select_input: offset 0x5d8 val 0x1
   write config: offset 0x3bc val 0x7f
   mux_reg 0x148, conf_reg 0x3b8, input_reg 0x5d4, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
   write mux: offset 0x148 val 0x10
   select_input: offset 0x5d4 val 0x1
   write config: offset 0x3b8 val 0x7f
   "
   this means imx6 pinctrl driver works as expected.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-21 11:23:48 +01:00
Purna Chandra Mandal
5f266c60bf drivers: pinctrl: Add pinctrl driver for Microchip PIC32.
In PIC32 pin-controller is a combined gpio-controller, pin-mux and
pin-config module. Remappable peripherals are assigned pins through
per-pin based muxing logic. And pin configuration are performed on
specific port registers which are shared along with gpio controller.
Note, non-remappable peripherals have default pins assigned thus
require no muxing.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-01 22:14:00 +01:00
Masahiro Yamada
84b8bf6d5d bug.h: move BUILD_BUG_* defines to include/linux/bug.h
BUILD_BUG_* macros have been defined in several headers.  It would
be nice to collect them in include/linux/bug.h like Linux.

This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.

I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot.  I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-25 10:39:59 -05:00
Simon Glass
318922b30f rockchip: rk3288: pinctrl: Fix HDMI pinctrl
Since the device tree does not specify the EDID pinctrl option for HDMI we
must set it manually. Fix the driver to handle this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
78a10b6656 rockchip: pinctrl: Implement the get_gpio_mux() method
Implement this so that the GPIO command will be able to report whether a
GPIO is used for input or output.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:35 -07:00
Simon Glass
63c52648e4 rockchip: pinctrl: Reduce the size for SPL
This file has many features that are not needed by SPL. Use #ifdef to
remove the unused features and reduce the code size.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:35 -07:00
Simon Glass
77eaa19e73 dm: pinctrl: Add a way for a GPIO driver to obtain a pin function
GPIO drivers want to be able to show if a pin is enabled for input, output,
or is being used by another function. Some drivers can easily find this
and the code is included in the driver. For some SoCs this is more complex.
Conceptually this should be handled by pinctrl rather than GPIO. Most
pinctrl drivers will have this feature anyway.

Add a method by which a GPIO driver can obtain the pin mux value given a
GPIO reference. This avoids repeating the code in two places.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:35 -07:00
Simon Glass
bea705c993 rockchip: pinctrl: Add a full pinctrl driver
We can make use of the device tree to configure pinctrl settings. Add this
support for the driver so we can use it in U-Boot proper.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:35 -07:00
Simon Glass
a4275f5e52 rockchip: Convert the PMU IOMUX registers into an array
This is easier to deal with when using generic code since it allows us to
use a register index instead of naming each register.

Adjust it, adding an enum to improve readability.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00