This patch changes the USB port scanning procedure and timeout
handling in the following ways:
a)
The power-on delay in usb_hub_power_on() is now reduced to a value of
max(100ms, "hub->desc.bPwrOn2PwrGood * 2"). The code does not wait
using mdelay, instead usb_hub_power_on() will wait before querying
the device in the scanning loop later. The total timeout for this
hub, which is 1 second + "hub->desc.bPwrOn2PwrGood * 2" is calculated
and will be used in the following per-port scanning loop as the timeout
to detect active USB devices on this hub.
b)
Don't delay the minimum delay (for power to stabilize) in
usb_hub_power_on(). Instead skip querying these devices in the scannig
loop until the delay time is reached.
c)
The ports are now scanned in a quasi parallel way. The current code did
wait for each (unconnected) port to reach its timeout and only then
continue with the next port. This patch now changes this to scan all
ports of all USB hubs quasi simultaneously. For this, all ports are added
to a scanning list. This list is scanned until all ports are ready
by either a) reaching the connection timeout (calculated earlier), or
by b) detecting a USB device. This results in a faster USB scan time as
the recursive scanning of USB hubs connected to the hub that's currently
being scanned will start earlier.
One small functional change to the original code is, that ports with
overcurrent detection will now get rescanned multiple times
(PORT_OVERCURRENT_MAX_SCAN_COUNT).
Without this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 20.163 seconds
With this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 1.822 seconds
So ~18.3 seconds of USB scanning time reduction.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Debugging has shown, that all USB hubs are being reset twice while
USB scanning. This introduces additional delays and makes USB scanning
even more slow. Testing has shown that this 2nd USB hub reset doesn't
seem to be necessary.
This patch now removes this 2nd USB hub reset. Resulting in faster USB
scan time. Here the current numbers:
Without this patch:
=> time usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 24.003 seconds
With this patch:
=> time usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 20.392 seconds
So ~3.6 seconds of USB scanning time reduction.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
This patch removes 2 mdelay(200) calls from usb_hub_port_connect_change().
These delays don't seem to be necessary. At least not in my tests. Here
the number for a custom x86 Bay Trail board (not in mainline yet) with
a quite large and complex USB hub infrastructure.
Without this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 28.415 seconds
With this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 24.003 seconds
So ~4.5 seconds of USB scanning time reduction.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Start with a short USB hub reset delay of 20ms. This can be enough for
some configurations.
The 2nd delay at the end of the loop is completely removed. Since the
delay hasn't been long enough, a longer delay time of 200ms is assigned
and will be used in the next loop round.
This hub reset handling is also used in the v4.4 Linux USB driver,
hub_port_reset().
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
This reverts commit 71105f50fe.
The reverted commit was applied for a temporary to unbreak
few Exynos boards on the release.
After the discussion about the change, this commit should be avoided.
Fixed device-tree for Exynos, allows reverting it without any issues.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
At present on x86 machines with use cache-as-RAM, the memory goes away just
before board_init_r() is called. This means that serial drivers are
no-longer unavailable, until initr_dm() it called, etc.
Any attempt to use printf() within this period will cause a hang.
To fix this, mark the serial devices as 'unavailable' when it is no-longer
available. Bring it back when serial_initialize() is called. This means that
the debug UART will be used instead for this period.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit 1057e6c broke use of the timer with driver model. If the timer is used
before relocation, then it becomes broken after relocation. This prevents
some x86 boards from booting. Fix it.
Fixes: 1057e6c (timer: Set up the real timer after driver model is available)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Output the pointer returned by each call to malloc(). This can be useful
when debugging memory problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix "warning: cast to pointer from integer of different size".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We have a nice framework around image fils to prepare a device tree
for OS execution. That one patches in missing device tree nodes and
fixes up the memory range bits.
We need to call that one from the EFI boot path too to get all those
nice fixups. This patch adds the call.
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI loader needs to maintain views of memory - general system memory
windows as well as used locations inside those and potential runtime service
MMIO windows.
To manage all of these, add a few helpers that maintain an internal
representation of the map the similar to how the EFI API later on reports
it to the application.
For allocations, the scheme is very simple. We basically allow allocations
to replace chunks of previously done maps, so that a new LOADER_DATA
allocation for example can remove a piece of the RAM map. When no specific
address is given, we just take the highest possible address in the lowest
RAM map that fits the allocation size.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Simon Glass <sjg@chromium.org>
After booting has finished, EFI allows firmware to still interact with the OS
using the "runtime services". These callbacks live in a separate address space,
since they are available long after U-Boot has been overwritten by the OS.
This patch adds enough framework for arbitrary code inside of U-Boot to become
a runtime service with the right section attributes set. For now, we don't make
use of it yet though.
We could maybe in the future map U-boot environment variables to EFI variables
here.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The original name of this function is unclear. This patch renames this
CRC16 function to crc16_ccitt() matching its name with its
implementation.
To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT image supports more than 32 bits in addresses by using #address-cell
field. Fixing 64-bit support by using this field.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FIT image supports load address and entry address. Getting these
addresses can use a common function.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This provides a way to load a FIT containing U-Boot and a selection of device
tree files. The board can select the correct device tree by probing the
hardware. Then U-Boot is started with the selected device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to obtain the short name for an Operating System,
architecture or compression mechanism. Provide functions for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an option to enable libfdt in SPL. This can be useful when decoding
FIT files in SPL.
We need to make sure this option is not enabled in SPL by this change.
Also this option needs to be enabled in host builds. Si add a new
IMAGE_USE_LIBFDT #define which can be used in files that are built on the
host but must also build for U-Boot and SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update this code to support CONFIG_BLK. Each USB storage device can have
one or more block devices as children, each one representing a LUN
(logical unit) of the USB device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Adjust a few things so that the addition of driver-models support involved
adding code rather than also changing it. This makes the patches easier to
review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
The limit on storage devices is USB_MAX_STOR_DEV but we use one extra
element while probing to see if a device is a storage device. Avoid this,
since it causes memory corruption.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
To ease conversion to driver model, add helper functions which deal with
calling each block device method. With driver model we can reimplement these
functions with the same arguments.
Use inline functions to avoid increasing code size on some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename this function to blk_get_device_part_str(). This is a better name
because it makes it clear that the function returns a block device and
parses a string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The current name is too generic. Add a 'blk_' prefix to aid searching and
make its purpose clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This is an enhancement that permits storing the environment file on an
EXT4 partition such as the root filesystem. It is based on the existing
FAT environment file code.
Following the previous patch, malloc() is never called before gd is set,
so we can remove the special-case check for this condition.
This reverts commit 854d2b9753 "dlmalloc: ensure gd is set for early
alloc".
Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using the early timer, we need to manually trigger setting up the
real timer. This will not happen automatically. Do this immediately after
starting driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit 84ca65aa4b.
On signature verification failures fit_image_verify() should NOT exit with
error. Only keys marked 'required' can cause image verification failure.
This logic is already there and works correctly.
Add a comment to make this clear.
Fixes: 84ca65aa (image-fit: Fix signature checking)
Signed-off-by: Simon Glass <sjg@chromium.org>
A recent change broke the 'bootm' command on sandbox. The root cause is
using a pointer as an address. Conversion from pointer to address needs to
use map_to_sysmem() so that sandbox can do the right thing. The problem was
pre-existing but uncovered by a recent commit.
Fix this. Also move fit_get_end() to the C file to avoid needing to include
mapmem.h (and thus asm/io.h) everywhere.
Fixes: 1fec3c5d (common/image.c: Make boot_get_ramdisk() perform a check for Android images)
Signed-off-by: Simon Glass <sjg@chromium.org>
Since commit fd61d39970:
spl: mmc: add break statements in spl_mmc_load_image()
RAW and FS boot modes are now exclusive again. So, if MMCSD_MODE_RAW fails, the
board hangs. This patch allows to try MMCSD_MODE_FS then.
It has been tested on a beaglebone black to boot on an EXT partition.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
$ make tools-all
...
In file included from tools/env/env_flags.c:1:0:
tools/env/../../common/env_flags.c: In function
‘env_flags_parse_varaccess_from_binflags’:
tools/env/../../common/env_flags.c:156:18: warning: implicit declaration
of function ‘ARRAY_SIZE’ [-Wimplicit-function-declaration]
for (i = 0; i < ARRAY_SIZE(env_flags_varaccess_mask); i++)
^
Seems like the other utilities just add a copy of ARRAY_SIZE since
there's nowhere to include it from (tools/imagetool.h,
tools/mxsimage.h). Let's do the same here.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Boards with a saved environment may use 'lcd' in their stdout environment
variable, expecting that this will enable output to the LCD. When the board
moves to use driver model for video, this will no-longer work. Add a
work-around to fix this. A warning messages is printed, and we will remove
the work-around at the end of 2016.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
This commit breaks bootup on sunxi boards, the get stuck
when running the main u-boot binary at:
CPU: Allwinner H3 (SUN8I)
I2C: ready
DRAM:
This reverts commit 8e7cba048b.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 9c11135ce0 ("image: fix getenv_bootm_size() function") fixed
the case where "bootm_low" is defined, but "bootm_size" is not.
Instead, it broke the case where neither "bootm_low" nor "bootm_size"
is defined. Fix this function again.
Fixes: 9c11135ce0 ("image: fix getenv_bootm_size() function")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Matthias Weisser <m.weisser.m@gmail.com>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The recent change to memalign() caused the allocation failure detection
code to be dead code; the "retry" logic is always activated under the same
condition that the original failure detection code is, and also fully
handles any possible failures. This patch solves the presence of dead
code.
Two alternatives are possible:
a) Delete the now-dead test, and rely on the "retry" path to handle any
allocation problems, as it does.
b) Make the "retry" path fall through to the existing (currently dead)
failure detection code, thus making it not-dead.
(b) was chosen since it reduces the diff between U-Boot's and the upstream
dlmalloc. This should make it marginally easier to import a new version of
dlmalloc in the future.
Reported by: Coverity Scan
Fixes: 4f144a4164 ("malloc: work around some memalign fragmentation issues")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The case of memory of size 0 is not that different from a memory of any other
size, so we remove the duplicate code and treat the small differences when it
is the case.
Signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Add trivial support for changing the U-Boot command prompt string
by setting PS1 and PS2 environment variables. Only static variables
are supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pull the code which displays U-Boot prompt and reads the command line
into a separate function. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The x86 build target "efi-x86" has no TEXT_BASE configured. And with the
introduction of CONFIG_BOOTDELAY for x86, this function is now called
for this board as well. Resulting in compile errors for this target.
Without TEXT_BASE it makes no sense to fill these values. So lets only
configure the env variable if TEXT_BASE is defined.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use of memalign can trigger fragmentation issues such as:
// Internally, this needs to find a free block quite bit larger than s.
// Once the free region is found, any unaligned "padding" immediately
// before and after the block is marked free, so that the allocation
// takes only s bytes (plus malloc header overhead).
p = memalign(a, s);
// If there's little fragmentation so far, this allocation is likely
// located immediately after p.
p2 = malloc(x);
free(p);
// In theory, this should return the same value for p. However, the hole
// left by the free() call is only s in size (plus malloc header overhead)
// whereas memalign searches for a larger block in order to guarantee it
// can adjust the returned pointer to the alignment requirements. Hence,
// the pointer returned, if any, won't be p. If there's little or no space
// left after p2, this allocation will fail.
p = memalign(a, s);
In practice, this issue occurs when running the "dfu" command repeatedly
on NVIDIA Tegra boards, since DFU allocates a large 32M data buffer, and
then initializes the USB controller. If this is the first time USB has
been used in the U-Boot session, this causes a probe of the USB driver,
which causes various allocations, including a strdup() of a GPIO name
when requesting the VBUS GPIO. When DFU is torn down, the USB driver
is left probed, and hence its memory is left allocated. If "dfu" is
executed again, allocation of the 32M data buffer fails as described
above.
In practice, there is a memory hole exactly large enough to hold the 32M
data buffer than DFU needs. However, memalign() can't know that in a
general way. Given that, it's particularly annoying that the allocation
fails!
The issue is that memalign() tries to allocate something larger to
guarantee the ability to align the returned pointer. This patch modifies
memalign() so that if the "general case" over-sized allocation fails,
another allocation is attempted, of the exact size the user desired. If
that allocation just happens to be aligned in the way the user wants,
(and in the case described above, it will be, since the free memory
region is located where a previous identical allocation was located),
the pointer can be returned.
This patch is somewhat related to 806bd245b1 "dfu: don't keep
freeing/reallocating". That patch worked around the issue by removing
repeated free/memalign within a single execution of "dfu". However,
the same technique can't be applied across multiple invocations, since
there's no reason to keep the DFU buffer allocated while DFU isn't
running. This patch addresses the root-cause a bit more directly.
This problem highlights some of the disadvantages of dynamic allocation
and deferred probing of devices.
This patch isn't checkpatch-clean, since it conforms to the existing
coding style in dlmalloc.c, which is different to the rest of U-Boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
It might be missed when converting spi_flash_probe() in cmd_sf.c.
This patch refers to commit fbb099183e ("dm: Convert
spi_flash_probe() and 'sf probe' to use driver model").
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Scan code 0x39 is CapsLock, which is not a printable character and thus
is not covered by either usb_kbd_numkey_shifted[] or usb_kbd_numkey[].
Fix the scan code check to avoid looking it up in either of the arrays.
Signed-off-by: Marek Vasut <marex@denx.de>
clang-3.8 reports that these functions are unused, remove them. As this
is the last part of CONFIG_MODEM_SUPPORT_DEBUG, drop that from README.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This enables boards to choose where to/from the environment should be
saved/loaded. They can then for example support using the same device
(dynamically) from which the bootloader was launched to load and save
env data and do not have to define CONFIG_SYS_MMC_ENV_DEV statically.
In my use case, the environment needs to be on the same device I
booted from. It can be the eMMC or an optional SD card.
I therefore would override mmc_get_env_dev in the board code, read the
CPU registers to determine where we booted from and return the
corresponding device index.
Cc: Tom Rini <trini@konsulko.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Variable _load_end_ points to end address of uncompressed buffer
(*not* uncomress_buffer_end / sizeof(ulong)), so multipling uncompressed
size with sizeof(ulong) is grossly incorrect in flush_cache().
It might lead to access of address beyond valid memory range and hang the CPU.
Tested on MIPS architecture by using compressed(gzip, lzma)
and uncompressed uImage.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There are a lot of unrelated files in common, including all of the commands.
Moving them into their own directory makes them easier to find and is more
logical.
Some commands include non-command code, such as cmd_scsi.c. This should be
sorted out at some point so that the function can be enabled with or without
the associated command.
Unfortunately, with m68k I get this error:
m68k: + M5329AFEE
+arch/m68k/cpu/mcf532x/start.o: In function `_start':
+arch/m68k/cpu/mcf532x/start.S:159:(.text+0x452): relocation truncated to fit: R_68K_PC16 against symbol `board_init_f' defined in .text.board_init_f section in common/built-in.o
I hope someone can shed some light on what this means. I hope it isn't
depending on the position of code in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The testpattern of the lcd was only working in 8bit mode(2x3 tiles in
different colors). With this patch now 8bit and 16bit is supported.
In 16bit mode there are 2x4 tiles in different colors.
The number of LCD-colors is defined in the include/configs/<boardfile>.h
Signed-off-by: Andreas Neubacher <neubacher.andreas@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
At present there is no indication that an invalid GPIO is used except that
the GPIO status is not displayed. Make the error more explicit to avoid
confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is convenient to be able to see the status of all regulators in a list.
Add this feature to the 'reg status' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Register video drivers with stdio so that they can be used for text output.
This needs to be done explicitly for now. At some point we should be able to
convert stdio itself to driver model and avoid this step.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
This command can use the bitmap display code in the uclass. This is similar
to the code in lcd.c and cfb_console.c. These other copies will go away when
all boards are converted to use driver model for video.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Before relocation we need to reserve memory for the video driver frame
buffers so that they can use this memory when they start up (after
relocation). Add a call to the uclass to permit this.
The current top and bottom of the region is stored in global_data so that
it can be checked post-relocation to ensure enough memory is available. No
video device should be probed before relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
These two functions are conceptually the same. Move them together in the
pre-relocation init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The LCD functions and definitions are not used with the driver model video
uclass. When all boards are converted over we can remove the file. For now,
use #ifdef to omit the contents.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
This reverts commit 3e303f748c.
The fix up in the /aliases node does not work under the following
scenarios:
- Not every non-DM serial driver was written to have a driver name
that conforms the format of "serial%d" or "eserial%d".
- With driver model serial, the stdio_devices[] stores the serial
device node name in the device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We can define this in the header file and use it in usb_storage.c. There is
no need to define it twice. Remove the #define from usb_storage.c.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this command to use map_sysmem() correctly so that it works on
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should not return a -ve error code from command functions. Instead,
return CMD_RET_FAILURE. This avoids the "exit not allowed from main input
shell" error messages from the hush shell.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, this function returns wrong size if "bootm_low" is defined,
but "bootm_size" is not.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We support max USB_MAXENDPOINTS, so need to use
"epno >= USB_MAXENDPOINTS", but not "epno > USB_MAXENDPOINTS".
If use ">", we may exceeds the array of if_desc->ep_desc.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: "Stefan Brüns" <stefan.bruens@rwth-aachen.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
Commit ecc30663 ("Fix board init code to respect the C runtime environment")
breaks x86. This was mentioned on https://patchwork.ozlabs.org/patch/548644
but not addressed. Correct it so that x86 boards boot again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should use ARRAY_SIZE, but not sizeof. The size of
env_flags_varaccess_mask is 16bytes, but we only need 4 loops.
If using 16 as the end condition, we may access memory that
not belong to array env_flags_varaccess_mask.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Report Coverity log:
Destination buffer too small (STRING_OVERFLOW)
string_overflow: You might overrun the 1024 byte destination string
lastcommand by writing 1025 bytes from console_buffer
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a 'poweroff' command to boot commands, this only gets enabled if the
board Kconfig does a "select CMD_POWEROFF".
Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
[hdegoede@redhat.com: Make the cmd conditional on a CMD_POWEROFF Kconfig]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Extend the ums command to accept a list of block devices. Each of these
will be exported as a separate LUN. An example use-case would be:
ums 0 mmc 0,0.1,0.2
... which would export LUNs for eMMC 0's user data, boot0, and boot1 HW
partitions. This is useful since it allows the host access to everything
on the eMMC without having to somehow stop the ums command from executing
and restart it with different parameters.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This will allow us to have multiple block device structs each referring
to the same eMMC device, yet different HW partitions.
For now, there is still a single block device per eMMC device. As before,
this block device always accesses whichever HW partition was most recently
selected. Clients wishing to make use of multiple block devices referring
to different HW partitions can simply take a copy of this block device
once it points at the correct HW partition, and use each one as they wish.
This feature will be used by the next patch.
In the future, perhaps get_device() could be enhanced to return a
dynamically allocated block device struct, to avoid the client needing to
copy it in order to maintain multiple block devices. However, this would
require all users to be updated to free those block device structs at some
point, which is rather a large change.
Most callers of mmc_switch_part() wish to permanently switch the default
MMC block device's HW partition. Enhance mmc_switch_part() so that it does
this. This removes the need for callers to do this. However,
common/env_mmc.c needs to save and restore the current HW partition. Make
it do this more explicitly.
Replace use of mmc_switch_part() with mmc_select_hwpart() in order to
remove duplicate code that skips the call if that HW partition is already
selected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As of gcc 5.2.1 for Thumb-1, it is not possible any
more to assign gd from C code, as gd is mapped to r9,
and r9 may now be saved in the prolog sequence, and
restored in the epilog sequence, of any C functions.
Therefore arch_setup_gd(), which is supposed to set
r9, may actually have no effect, causing U-Boot to
use a bad address to access GD.
Fix this by never calling arch_setup_gd() for ARM,
and instead setting r9 in arch/arm/lib/crt0.S, to
the value returned by board_init_f_alloc_reserve().
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
board_init_f_mem() alters the C runtime environment's
stack it is actually already using. This is not a valid
behaviour within a C runtime environment.
Split board_init_f_mem into C functions which do not alter
their own stack and always behave properly with respect to
their C runtime environment.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
The function hash_show is now only called by hash_command, so mark it as
static (and drop from hash.h). We only call hash_command when any of
CONFIG_CMD_CRC32, CONFIG_CMD_SHA1SUM or CONFIG_CMD_HASH are set. Since
hash.c is linked in unconditionally we must take extra care with
functions that bring in read-only strings as these will not be
discarded.
Signed-off-by: Tom Rini <trini@konsulko.com>
To boot Linux, we should prevent Initramdisk and FDT from going too
high.
Currently, boot_relocate_fdt() checks "fdt_high" environment first,
and then falls back to getenv_bootm_mapsize() + getenv_bootm_low()
if "fdt_high" is missing.
On the other hand, boot_ramdisk_high() only checks "initrd_high" to
get the address limit for the Initramdisk. We also want to let this
case fall back to getenv_bootm_mapsize() + getenv_bootm_low().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the SCSI command to use driver model for its PCI interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_bus_find_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since 51209b1f42 ("Use common mtest iteration counting"),
do_mem_mtest has always reported 0 errors and hence returned 0, even
if errors were detected. Fix the helpers mem_test_alt() and
mem_test_quick() to return the number of errors found.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Commit: dm: core: Enable optional use of fdt_translate_address()
Enables use of this function as default, but after this it's not
possible to get dev address for the case in which: '#size-cells == 0'
This causes errors when getting address for some GPIOs, for which
the '#size-cells' is set to 0.
Example error:
'__of_translate_address: Bad cell count for gpx0'
Allowing for that case by modifying the macro 'OF_CHECK_COUNTS',
(called from )__of_translate_address(), fixes the issue.
Now, this macro doesn't check, that '#size-cells' is greater than 0.
This is possible from the specification point of view, but I'm not sure
that it doesn't introduce a regression for other configs.
Please test and share the results.
Tested-on: Odroid U3, Odroid X2, Odroid XU3, Sandbox.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
At present USB keyboards are not properly removed with driver model. Add the
code to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The current limit of 5 is not enough for the driver model USB tests. Really
we should not have a limit but the driver model code still uses the
usb_dev_desc[] array, which has a limit.
Increasing the limit by 2 should not bother anyone. Adjust it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Use snprintf to replace sprintf.
Coverity log:
"
Unbounded source buffer (STRING_SIZE)
string_size: Passing string init_val of unknown size to sprintf.
"
Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Before calling hsearch_r, initialize callback entry to NULL.
Coverity log:
"
Uninitialized scalar variable (UNINIT)
uninit_use_in_call: Using uninitialized value e.
Field e.callback is uninitialized when calling hsearch_r.
"
Reported-by: Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
